Introduction

Coffee is a plant belonging to the family Rubiaceae, genus coffea. Its seeds are called coffee beans and can be processed into drinks. Although coffee lifespan may extend up to 100 years, its most productive years are from 5 to 25 and can equally grow from 5 to 25 m tall [National Coffee Association (USDA 2018)].

Coffee originated from Ethiopia and then spread across to Egypt, Yemen and Italy and all over Europe. Coffee has continuously gained a place in the world. Globally, coffee is the second largest most traded commodity after petroleum. It is mostly produced in the tropics and consumed in the temperate region. Three species of coffee dominate the international market thus; Arabica (Coffea Arabica) 70% has the highest quality in terms of taste and aroma, Robusta (Coffea Canephora) 28% has the highest caffeine content and Coffea Liberica 2% (von Enden et al. 2002).

Problem statement

Coffee processing method can be either dry or wet. The wet processing system uses large volume of water and therefore generates high volume of polluted effluent which are traditionally discharged easily into the nearby stream or river. Coffee processing by-product includes pulp with 43%, mucilage 12% and parchment 6.1%. This effluent is generally made of high concentration of organic matter and suspended solid and is highly acidic (Navitha and Kousar 2018; Sahana et al. 2018). Another major problem associated with wet coffee processing is the high amount of water required for processing approximately 15–20 L to 1 kg of coffee bean; if there is no recycling of water, then the resources themselves are at stake (Dadi et al. 2018). According to Cardenas et al. (2009), there is need to treat the coffee effluent before discharge because it was observed that the water pollution level of streams and rivers close to coffee processing plants is very high. Additionally, it has been observed that there has been minimal or no comprehensive review with regard to how coffee effluent is being managed in recent times.

Furthermore, the effluent produced by coffee processing plants is colored containing different macromolecules such as polyphenols (e.g., melanoidins) and caffeine. The coffee melanoidins consist of groups of ligand such as tannins, polysaccharides and combinations of them (Cardenas et al. 2009). These macromolecules are tough to degrade using conventional biological treatment processes and are accountable for its dark brown color (Péerez et al. 2007). Consequently, the pollution resulting from the discharge of colored effluent is responsible for its opacity, high chemical and biological oxygen demand, causing eutrophication, blocking light and affecting photosynthesis (Takashina et al. 2018; Tokumura et al. 2008; Péerez et al. 2007).

Although various physicochemical methods have been developed to remove the recalcitrant compound in CPWW, there is still need to explore other methods that can be cost effective as well. Pollutant removal techniques reported by studies include zero-valent iron treatment (Tomizawa et al. 2016) ionizing radiation, adsorption, electrochemical oxidation using steel electrodes, and, recently, chemical flocculation coupled with advanced oxidation processes (UV/H2O2, UV/O3 and UV/H2O2/O3). There has so far not been any review on the current coffee processing wastewater treatment. Although Shanthakumar (2018) attempted a mini review on coffee processing wastewater treatment (CPWW) methods, the review has failed to highlight the pros and cons of the methods mentioned, and other treatment methods were not also captured. This work hopes to fill in the gap by providing information on all current treatment techniques that has been adopted for CPWW, highlighting clearly the advantages and their disadvantages. Furthermore, this work suggests a viable and less explored method in the removal of recalcitrant compounds found in coffee processing wastewater.

Aim and objective

The aim of this paper is to present a review on the current methods of coffee effluent treatment with the sole objective of presenting the most appropriate and nascent technology that takes into consideration all parameters of concern (effectiveness, availability, affordability and ecologically friendly) for effective coffee effluent treatment.

The anatomy of a coffee berry

To have a better understanding of managing coffee processing effluent, it is very vital to understand how the organic pollution is generated.

The coffee berry outer skin is called the pericarp; beneath it there lies a thin layer of pulp (mesocarp) followed by a slimy layer called the pectin layer (parenchyma) (Tori Gay 2018). The bean itself is covered in an endocarp commonly referred to as parchment; inside the bean there is another thin layer called the silver skin (epidermis) (Fig. 1).

Fig. 1
figure 1

The anatomy of coffee berry

Coffee processing

Due to the fact that the quality of coffee bean starts to degrade few hours after being picked from the farm, processing is done immediately. This is why coffee processing plants or areas should be located close to the coffee farm (Tori Gay 2018). Each technic and level of processing comes with its pollution potential (Fig. 2). Additionally, the robustness of the processing determines the quality of the end product (von Enden et al. 2002).

Fig. 2
figure 2

Source: Author

Schematic diagram of coffee processing.

The dry method of coffee processing

The dry method is the simplest with minimum pollution potential. Coffee berries are left under the sun after picking until the moisture content reaches a minimum of 10%, removal of the outer skin and parchment follows suit. The dry method requires a large space for the sun drying and does not usually produce qualitative coffee; furthermore, the dry process can easily be hampered by raining season in many parts of the world (Lucy 2003).

The wet method

This method entails different stages of processing (Fig. 2) and requires high technical knowhow to ensure production of good quality coffee. The processing is preceded by sorting, where coffee berries are immersed in water. The poorly developed, degraded or diseased floats and is removed, and other detritus such as twigs or leaves that may have been collected along with berries are also removed. This is followed by depulping; it involves removing the outer layer of the coffee seed (exocarp, mesocarp), leaving a slimy coating of mucilage around the bean. This process generates high level of organic matter that makes it very difficult to degrade the mucilage layer of the coffee berries (Rattan et al. 2015). Next is fermentation of the mucilage whereby the mucilage is acted upon by microorganism in that way decomposing the layer, the coffee bean is again washed. Fermentation time is determining by the temperature of the given processing area. The simplest test for complete fermentation according to Por and Katzeff (2001) is by pushing one’s hand into the pile of coffee bean when it makes a hole and then it is completely fermented. Washing comes next after the fermentation is complete; the process involves immersing the bean in clean water, stirring and rinsing, and the process continues until it is devoid of any trace of mucilage, because having any residue of mucilage could affect the quality of the end product. After the bean has been freed from all pulpy residue, it is subjected to drying either by solar energy or by the use of mechanical dryers that are powered either electrically or fueled by gas where the moisture content is reduced to 10–12% by simply using a digital grain moisture meter for measurement (Kebede et al. 2010); the dryness of the coffee is very important because it increases the quality invariably increasing the value, and it also inhibits the growth of fungi on the seed.

Biological and physicochemical characteristics and effects of coffee processing wastewater

It has been reported by several studies that coffee wastewater is characterized by very high chemical oxygen demand (COD), biological oxygen demand (BOD), acidic content, odor and color (Tokumura et al. 2006; Chagas et al. 2015; Navitha and Kousar 2018; Gupta et al. 2009; Kebede et al. 2010; von Enden et al. 2002; Padmapriya et al. 2013, 2015; Gerardi 2003; Woldesenbet et al. 2014).

It is paramount to note that the main environmental effect of organic pollution in water is the decrease or insufficiency of oxygen and opacity (Morales et al. 2005). The presence of toxic chemicals like tannins, phenolic and alkaloids inhibits biological degradation or organic materials in water bodies where the effluent has been discharged. Microbial processes break down the organic substances released into water bodies slowly, using up the oxygen from the water. As demand for oxygen begins to exceed supply, decrease in oxygen content slowly creates anaerobic condition (Rattan et al. 2015; Tokumura et al. 2008).

This phenomenon results in very high amount of oxygen needed to break down organic waste in a wastewater (BOD) and also a high amount of oxygen needed to combine with chemicals (COD). The anaerobic conditions created in wastewater are responsible for odor and could be very fatal to aquatic inhabitants; bacteria that seep into potable water sources can as well cause direct health implication on humans (Woldesenbet et al. 2014). Color is a significant factor for aquatic life in the manufacture food from sun rays. The photosynthetic activity decreases due to dark color. This in turn will affect other parameters like temperature, DO and BOD (Siddiqui and Waseem 2012)

In general, the need for a sustainable wastewater management practices for industries is driven by many factors including legislation, disposal limits in sensitive water bodies, protection from water-related risk, economic consideration with regards to cost of water, corporation image, (as a form social corporate responsibility of company or even as part corporation obligation to the environment). Therefore, this review looks at the methods that have been in use so far and provide a not-to-common technology in the management coffee processing wastewater.

Current treatment technologies and their advantages and disadvantages

For any treatment to be ascertained as effective, the method must take into cognizance operational cost, environmental friendliness as well as the different demand for water quality in relation to water uses so as to optimize the reuse based on the water-fit-for-use principle. Wastewater must also be discharged based on predetermined discharge limits. Stability and reliability of the management method should also be considered (Hubbe et al. 2016).

Having highlighted the severity of improper management of coffee effluent above, this section highlights various methods that have been applied in managing the coffee effluent with their cons and pros.

Physicochemical treatment

Physicochemical treatment methods of industrial wastewater have been preferred recently compared over biological treatment because of its ability to break complex compound in wastewater in relatively short period of time (e.g., few hours) in a controlled environment (Takashina et al. 2018; Rodrigues et al. 2014).

Zero-valent iron (ZVI) treatment

Zero-valent iron (ZVI) particulates are non-toxic, abundant and low-cost material and easily recovered by magnetism; they have in recent times been used to treat both organic and inorganic pollutants in different wastewater (Fu et al. 2014; Tomizawa et al. 2016). Their mechanism of pollution removal is reductive degradation, oxidative degradation, adsorption and precipitation. Despite their successes, spent ZVI particulates are not easily regenerated, which makes the process not economically viable as materials need to be replaced after treatment (Tomizawa et al. 2016).

Photo-Fenton method

Recently, many OAP treatments of coffee effluent have been brought into the lime light such as photo-catalysis with H2O2 and Fe2+, with ZnO (Tokumura et al. 2008). This method uses the catalytic reaction between ferrous ions in solution and hydrogen peroxide producing hydroxyl (a specie with high oxidation potential) which is the key reagent in breaking down recalcitrant compound-related lignin (Hubbe et al. 2016). Tokumura et al. (2008) used varying doses of H2O2 and UV light to decolorize coffee effluent, 93% of coffee effluent color was removed in 250 min (Kondo et al. 2010), by using combined biological and chemical treatment with the anaerobic up-flow anaerobic sludge blanket (UASB) reactor and photo-Fenton to achieve 95% BOD removal at the optimal molar concentration of H2O2 as 2.5 × 10−1 mol L−1 and that of F2+ 6.3 × 10−2 mol L−1.

Although the photo-Fenton reaction is very effective for decolorization of coffee eluent, the additional supply of hydrogen peroxide consumed in the process and the control of optimal pH at around 3.0 are drawbacks (Tokumura et al. 2006, 2008; Yamal-Turbay et al. 2012; Villanueva-Rodríguez et al. 2014).

Ultraviolet radiation (UV) catalysis (with ozone)

Ozonation has been advocated to be a better option as compared to photo-Fenton being a stronger oxidant of many organic compounds (Satori and Kawase 2014). Studies reported that the main shortcoming of ozonation is its low mineralization, but this is usually countered by UV or hydrogen peroxide (Hubbe et al. 2016). There were also claimed that UV application alone is less effective method of treatment unless it is combined with other AOP which prove that large amount of organic compound loading, such as color and turbidity were removed effectively (Takashina et al. 2018; Ashraf et al. 2016). Péerez et al. (2007) employed photo-oxidation technique using UV/H2O2 preceded by coagulation–flocculation to remove 87% COD in coffee wastewater.

Electro-oxidation

According to Hubbe et al. (2016), electro-oxidation could be defined as a process where voltages and other factors in an electrode are optimized for in-situ generation of oxidizing and reactive species. In this method, electrolysis produces different oxidative radicals (e.g hydroxyl, chlorine,) as organic compounds directly degrade on the electrode. In this method, electrolysis produces different oxidative radicals (e.g., hydroxyl, chlorine,) as organic compound directly degrade on the electrode.

Electro-oxidation has been studied by many researchers in the treatment of coffee processing wastewater (Ibarra-Taquez et al. 2017). Cardenas et al. (2009) used a dimensionally stable anode that is composed of titanium with a film of ruthenium, cobalt oxide and iridium to reduce the level of pollutant after pretreatment with coagulation/chemical flocculation. Bejankiwar et al. (2003) studied the removal of COD and color after biological pretreatment showing that steal anode was effective in removing COD in coffee wastewater.

Membrane filtration It is a mechanical separation technique for removing micron-sized contaminants (Park et al. 2015). The technique has been reportedly successful in the treatment of pulp and paper industrial wastewater (Hubbe et al. 2016; Puro et al. 2010; Pizzichini et al. 2005) and as co- treatment in many respect (Santhosh et al. 2016; Zheng et al. 2013). There are basically four classification of membrane filtration: microfiltration with typical pore size of 0.1–2 μm, ultrafiltration 2–100 nm, nano-filtration 1–5 nm and reverse osmosis <  1 nm (Barakat 2011; Hermosilla 2016; Sójka-Ledakowicz et al. 1998).

Despite its wide usage, the main drawback of membrane filtration is that only it separates and does not change any components of the wastewater. Therefore, in the case of highly polluted wastewater such as coffee processing wastewater additional treatment method is needed as reported by Tacias-Pascacio and Torrestiana-Sanchez (2019) whereby a combined system of anaerobic baffled bioreactors and membrane filtration was used to remove COD 81%, TS 72%, TSS 100%, TDS 61%; yet, its effectiveness in the removal of recalcitrant elements such as phenol that makes up the coffee color has not been reported.

Another very common issue encountered by this method is the clogging and fouling of membrane. Recent studies were tilted to finding solution to this problem factors like rate of pressure, pretreatment before subjection to membrane filtration (Qu et al. 2012) and more recently electric treatment of the membrane; others include optimization of temperature and pH. A water treatment company operating in Malaysia developed an operator-friendly pressurized membrane system membrane bioreactor plant which will be used to treat and reuse wastewater from instant coffee processing company. Although the method will effectively remove COD and free oil and grease (Asia 2012), there is no mention of the removal of acidity and color which is the major issue with coffee processing wastewater

Biological methods

Various forms of filtration have been studied in connection with bioreactors to speed up biological decomposition (Hubbe et al. 2016) bearing in mind the health and environmental effect of direct discharge of coffee effluent without treatment (Selvamurugan et al. 2010; Dinsdale et al. 1997; Rossmann et al. 2013; Fia et al. 2012). Biological treatment is widely practiced; one of the major objectives of biological treatment is the removal of BOD, and such treatment has been found to be ineffective in the removal of color or other acidic components of the coffee wastewater and processes require a long period (a few months) to completely degrade organic materials. Biological treatment includes but not restricted to aerobic/anaerobic treatment, spray irrigation, activated sludge, immobilization, enzyme treatment, the use of bioreactors (Gupta et al. 2009; von Enden et al. 2002; Navitha and Kousar 2018).

Expanded granular sludge bed (EGSB) bioreactor Several anaerobic processes have been developed and studied to treat CPWW, such as studies on the flow pattern, toxicity inhibition, start-up, optimization, kinetics and operation conditions. The hydraulic retention time (HRT) is one of the most important independent variables for the control of this kind of anaerobic bioreactor, because it directly influences the anaerobic digestion processes and the hydrogen transfer and can produce the cell washing phenomenon (Cruz-Salomón et al. 2017).

It has been established that this type of bioreactor is an excellent system for treating high organic load effluent, but its major drawback is it does not remove the nutrients (N and P). Another problems of the anaerobic biological degradation are associated with the high content of fermentable organic matter in the effluent that causes a fast acidification of the wastewater resulting in a high production of VFA (Somasiri et al. 2008 and Buzzini et al. 2007).

Therefore, it is necessary to monitor the content of VFA for the good performance of the anaerobic bioreactor. Therefore, it is necessary to monitor the content of VFA for the good performance of the anaerobic bioreactor as well as Hydraulic retention time (HRT) because these factors affect EGSB bioreactor performance (Cruz-Salomón et al. 2017).

Chemical coagulation and flocculation is also reported to be efficient, easy to handle and cheap method of coffee wastewater treatment. It does not require pretreatment (Novita et al. 2012). Studies reviewed showed that although color removal was effective, COD reduction was not effectively achieved due to the fact that the process cannot break the complex binding of organic matter in coffee wastewater (Novita et al. 2012).

The settling down of solid particles in effluent as a result of gravity can be enhanced by electrochemical coagulation. Electrochemical coagulation method has been credited to be efficient in the removal of color, COD and SS in coffee wastewater (Novita et al. 2012; Panchangam and Janakiraman 2015; Sahana et al. 2018). Removal of suspended solid and oxygen demand occurs when high charged cation agent such as aluminum sulfate coagulant is used to neutralize to neutralize negatively charged wastewater solid, followed by high-mass polyelectrolyte such as acrylamide (flocculants) (Hubbe et al. 2016).

Electrochemical method consists of two conductive metal plates (anode and cathode) connected to an external power source where oxidation corrodes the anode material and the cathode is subjected to passivation (Sahana et al. 2018). In relation to other traditional methods of coffee processing wastewater treatment, electroplating has more advantages which include high ability to remove contaminants that are generally difficult to remove, cost effectiveness, environmental compatibility, energy efficiency, safety (Sahana et al. 2018).

Downside is noted in the gradual reduction of the effectiveness of the treatment by the passivation of cathode as current continues to flow through it. It also requires higher rate of energy supply in relation to most treatment technologies. Furthermore, the presence of tannins apparently causes a short circuit in the coagulation and the flocculation process (Novita et al. 2012).

Adsorption In the quest for cheaper and yet efficient technology for the removal of organic matter, several agricultural by-products such as corn stalk, rice husk, chitosan, chitin, peat, wood have been used as adsorbents (Devi et al. 2008). Due to their hydrophobicity, suitably high surface area and affinity, activated carbon products have been used in industrial wastewater treatment. Activated carbon technology has shown great efficiency in the removal of contaminant with very cheap and readily available adsorbent than many conventional methods of organic wastewater treatment method (Devi et al. 2008).

Although there are very few studies that adopted the adsorption technology in the management of coffee effluent, many studies have reported the use of coffee by-products as effective adsorbent in the removal of heavy metals (Anastopoulos et al. 2017; Jeguirim et al. 2017; Nitayaphat 2017; Utomo and Hunter 2006). However, Mahesh et al. (1999) reported the study of tannin removal by adsorption from coffee wastewater, and they discovered that the process effectiveness was highly dependent on pH (e.g., 3–5 using activated coconut shell and 5–6 for commercial activated carbon) even though the method has some disadvantages associated with additional cost in relation to high energy needed to activate the carbon (Shawwa et al. 2001).

Ionization irradiation

Aguilera and Consuegra (1998) studied the implication of ionizing radiation on coffee effluent organic substances that could not degrade by biological treatment alone. The method was preceded by chemical treatment. Although the method is safe, fast and effective and it does not generate any pollution, its downside has the high cost associated with the treatment method.

Advantages and disadvantages of CPWW treatment techniques

MethodsAdvantagesDisadvantagesApplication
Zero-valent iron (ZVI)Effective in removing color and TOCMaterials need replacement after every treatmentTomizawa et al. (2016)
Photo-FentonEfficient in removing color in coffee wastewaterAdditional supply of hydrogen peroxide is required. There is also a very low pH at which the process does not neutralize. It is also time-consumingTokumura et al. (2008)
OxidationRelatively low cost, the highest treatment percentage obtained was 75.99% for caffeic acidShort catalytic lifespan of the enzyme when the polymerization process is not active
Enzyme activity is dependent on the temperature, which makes the process cumbersome
Torres et al. (2016) and Chagas et al. (2015)
Fungal speciesFungi have high potential of removing physicochemical parametersTakes longer time for the fungi to effect considerable result. Low tolerance for fungal species to changes in pH levelNavitha and Kousar (2018) and Hubbe et al. (2016)
Spray irrigationLow cost and does not require special skillThe process did not put into consideration the fact that ground water can be confined and unconfined. Additionally, it may take longer time for pollutant to leach into ground water. Furthermore, it could also result in anaerobiosisLoehr et al. (1988), Gupta et al. 2009 and Kebede et al. (2010)
Aerobic/anaerobic digestionIt is the most popular treatment methodThis process is time-consuming as bacterial consortia responsible for the degradation process require time to adapt to the new environment before they start to consume organic matters to grow; in addition another disadvantage of this method is the fact that the volume and strength of the effluent may not be consistent and therefore inhibit the process and the required efficiency to treat the effluent. Finally, this method will require a further post-treatment to meet the environmental standard for disposalPadmapriya et al. (2013, 2015), von Enden et al. (2002) and Gerardi (2003)
CoagulationAchieved 71.9% and 97.8% of COD color removal, respectively, with 7.5 g/L of FeCl3 at pH5The final result has a low pH which is another problem to disposalNovita et al. (2012)
Activated carbonAvocado removed 98.2 and 99.1 of COD and BOD, while commercial activated carbon 99.02% and 99.35%, respectively. The most effective method of removing COD and colorRequires huge amount of energyDevi et al. (2008)
Membrane filtrationVery useful as a co treatment methodClogging and fouling of membrane, as well as required pressureHermosilla (2016)
Electrochemical coagulationVery effective for the recovery and reuse of sludge
(64–85%) color removal @ pH 6 with ferrous sulfate
Requires high level of expertise, is not cost effective to small scale coffee manufacturers not efficient in color removal. Factors affecting this process include electrode material, characteristics of wastewaterPanchangam and Janakiraman (2015) and Sahana et al. (2018)
Using Gamma radiationThe method is safe, fast and effective and it does not generate any pollutionIrradiation is a high-cost treatmentAguilera and Consuegra (1998)

Ion exchange

Color and organic matter removal from coffee and other colored effluents have been relatively successful; especially the physicochemical methods mentioned earlier, for these treatments to be generally considered effective, factors such as environmental friendliness demand for energy and cost of operation should also be considered. Ion exchange is the redistribution of ions between two phases of diffusion. Ion exchangers are solid materials that can take up charged ions from a solution and discharge a corresponding amount of the other ions into the solution (Kremer 1954). The ability to exchange ions is dependent on the property of the structure of the solid material (Lucy 2003; Inglezakis and Poulopoulos 2006).

Ion exchange resins are insoluble polymer that comprise basic or acidic functional groups and have the capacity to exchange counter ions within an aqueous solutions surrounding them. Ion exchange is an adsorption phenomenon where the mechanism is electrostatic. Electrostatic forces adsorb ions to charge functional groups of the ion exchange resin, and the adsorbed ion replaces the ions on the surface of the resin on a 1:1 charge ration basis (Bashir et al. 2010). The resins are fabricated from an organic polymer substrate backbone; they are usually white or yellowish available in the form of small beats (1–2 mm). The beats are generally porous providing a high surface area to maintain electro-neutrality. All ions exchangers have fixed ionic group that are balanced by the counter ion (Eq. 1) (Noble and Terry 2004):

$$ A^{ + } + \, \left( {R - } \right)B^{ + } \leftrightarrow B^{ + } + \, \left( {R - } \right)A^{ + } . $$
(1)

One prominent importance of ion exchange material is the ability to use and reuse the material (Wheaton and Lefevre 1981). Ion exchange technology is utilized in many capacities such as agriculture, food processing, medical research and chemical synthesis and mostly used in water treatment processes. Their applicability to water softening, environmental remediation, wastewater treatment, hydrometallurgy, chromatography, biomolecular separations and catalysis has been highlighted in several publications (Alexandratos 2009; Silva et al. 2018). For the basis of this study, we shall be looking at their applicability in water treatment

Ion exchange techniques have been found to successfully remove heavy metals such as clinoptolite and heulandite to remove strontium (Chernjatskaja 1988); using hexacyanoferrate and phenolic resins to remove Cesium (Harjula et al. 1994; Samanta et al. 1992), using titanate exchangers to treat nuclear waste (Dosch et al. 1993), using zeolite for thorium ions removal (Sinha et al. 1994). Successes with ion exchange technique have also been recorded in recent times with regard to the treatment of various kinds of contaminated water. For examples, Bashir et al. (2010) effectively employed ion exchange technology to successfully remove color COD and ammonia nitrate in a field leachate and also for removal of ammonia from wastewater (Jorgensen and Weatherley 2003). Its advantage is seen in its capacity to remove all ionizable and ionic species from aqueous solution. It is highly efficient, and there is availability of large variety of resins that can easily be reused and recycled. The disadvantage of ion exchange resin technique is that it requires pre-filtration process before it can be used.

Advocacy of ion exchange resins for the treatment of CPWW is due to the physicochemical characteristics of ion exchanger. Major color compounds are anionic (R‐COO‐H+) from degraded plant tissue. Their chemical structure is polyphenol structure with COOH residue with molecular weight of more than 10,000 (i.e., humic acid) which can be removed by strong base anion. Meanwhile, minor color compounds are cationic (RNH3+) which can be originated from organic compound with amine residue. The color compounds also can presence with COOH group (i.e., degraded protein) and therefore could be considered as both cationic and anionic in nature; depending on pH. This compound can be removed by strong acid cation. Mechanism of pollutant removal can be by both ion exchange and physical adsorption as illustrated below

figure a

.

The ion exchange process (polar attraction) Interaction between positively charged quaternary ammonium functional group of resin and negatively charged carboxylic or sulfonic group of pollutant.

Physical adsorption (nonpolar attraction) Involves van der Waals interactions between the nonionic and the ion exchanger polystyrene matrix.

Conclusion

In conclusion, the coffee manufacturing industry plays a huge role in the world today both as a business venture and as a consumable commodity, yet the processing of a good quality coffee comes at a price. For adequate environmental, resource management and sustainability, the use of ion exchange process in the removal or organic pollutant in wastewater is highly recommended bearing in mind the successes recorded in other field similar to coffee wastewater over the years. T now, there has not been any report on the use of ion exchangers in coffee processing wastewater management. It is therefore recommended that researchers should consider this treatment process for cheap, effective as well as environmentally friendliness.