Abstract
In this study, TiC coating and TiC/Ni composite coating were formed on the P110 steel surface, which is commonly used in oil casing, by argon arc cladding, to improve the wear resistance of P110 steel surface and support oil production. The microstructure, hardness, and wear resistance of the two coatings were analyzed and compared. The results show that TiC/Ni composite coating is superior to single TiC coating in microstructure, hardness, and wear resistance. The addition of Ni element makes the TiC particles in the coating finer and more evenly dispersed, and the addition of Ni element also effectively reduces the shedding of TiC particles during the wear process, thus improving the overall hardness and wear resistance of the coating. The formation of TiC/Ni composite coating effectively improves the wear resistance of P110 steel surface and provides an effective technical scheme for prolonging the service life of oil casing.
Similar content being viewed by others
Data Availability
All data and models generated or used during the study appear in the submitted article.
References
Shi L, Wang H G, and Ji G D, Current situation, challenges and developing trend of CNPC’ soil & gas drilling [J]. Nat Gas Ind (2013). https://doi.org/10.3787/j.issn.1000-0976.2013.10.001
Tan S, Zhang W, Duan L, Pan B, and Li C, Effects of MoS2 and WS2 on the matrix performance of WC based impregnated diamond bit [J]. Tribol Int 131 (2019) 174–183. https://doi.org/10.1016/j.triboint.2018.10.038
Wang H, Huang H C, Bi W X, Ji G D, and Zhuo L B, Deep and ultra-deep oil and gas well drilling technologies: progress and prospect [J]. Nat Gas Ind B 9 (2022) 141–157. https://doi.org/10.1016/j.ngib.2021.08.019
Yang M Z, Wiskel J B, Ivey D G, Gaudet M, and Henein H, The effect of tempering conditions on carbides in P110 casing steels [J]. Mater Sci Technol (2023). https://doi.org/10.1080/02670836.2022.2159455
Zhu S D, Lin G F, Bai Q Z, Liu H, and Yin Z F, Influence factors of corrosion of casing P110 steel [J]. Mater Prot. 91 (2009) 48–51. https://doi.org/10.16577/j.cnki.42-1215/tb.2009.01.012
Osman O A, Merah N, Abdul Samad M, Ali Baig M M, Alshaarawi A (2022) Casing wear and wear factors: new experimental study and analysis [J/OL] https://doi.org/10.3390/ma15196544.
Díez-Pérez I, Gorostiza P, Sanz F, and Müller C, First stages of electrochemical growth of the passive film on iron. J Electrochem Soc 148 (2001) 307–313.
Tang Y M, Miao Y F, Zuo Y, Zhang G D, and Wang C L, Corrosion behavior of steel in simulated concrete pore solutions treated with calcium silicate hydrates [J]. Constr Build Mater 30 (2012) 252–256. https://doi.org/10.1016/j.conbuildmat.2011.11.033
Lin N M, Xie F Q, Zhou J, Zhong T, and Tian W, Microstructures and wear resistance of chromium coatings on P110 steel fabricated by pack cementation [J]. J Cent South Univ Technol 17 (2010) 1155–1162. https://doi.org/10.1007/s11771-010-0612-3
Lin N M, Zhou P, Zou J J, Xie F Q, and Tang B, Wear and corrosion resistance of electroless plating Ni-P coating on P110 steel [J]. J Wuhan Univ Technol-Mater Sci Ed 30 (2015) 622–625. https://doi.org/10.1007/s11595-015-1200-z
Liu B, Yan S M, He Y, Li H J, and Xiang Y X, Preparation of Ni-W-eGO composite coatings and investigation of its mechanical properties and corrosion resistance [J]. Coll Surf A: Physicochem Eng Aspe 629 (2021) 127385. https://doi.org/10.1016/j.colsurfa.2021.127385
Chang J H, Liu T H, Chou J M, Hsieh R I, and Lee J L, Microstructural and microhardness characteristics of induction melted nickel-based alloys [J]. Mater Chem Phys 120 (2010) 702–708. https://doi.org/10.1016/j.matchemphys.2009.12.020
Pan C G, Shi J, Wei J, Zhao C X, and Wang H J, Effect of preheating temperature on the microstructure and corrosion resistance of TiC–Ni coating by CS/PHIP [J]. Trans Indian Inst of Metals 72 (2019) 1869–1879. https://doi.org/10.1007/s12666-019-01664-6
Li J N, Su M L, and Zhang L W, Microstructure performance and synthesis of the argon-arc clad cobalt base composite coating [J]. Surf Rev Lett 26 (2018) 1850189. https://doi.org/10.1142/s0218625x18501895
Meng J S, Shi X P, Zhang S J, Wang M Y, and Bian L H, Friction and wear properties of TiN-TiB2-Ni based composite coatings by argon arc cladding technology [J]. Surf Coat Technol 374 (2019) 437–447. https://doi.org/10.1016/j.surfcoat.2019.06.015
Meng J S, Shi X P, Zhang S J, Wang M Y, and Cui W C, Structure and properties of graphene reinforced Ti-based composite coatings on TC4 alloy by argon arc cladding [J]. IOP Conf Ser: Mater Sci Eng 715 (2020) 012002. https://doi.org/10.1088/1757-899x/715/1/012002
Wang H Q, Sun J S, Li C N, Geng S N, and Wang G L, Microstructure and mechanical properties of molybdenum–iron–boron–chromium cladding using argon arc welding [J]. Mater Sci Technol 32 (2016) 1694–1701. https://doi.org/10.1080/02670836.2016.1140926
Li J N, Su M L, and Zhang L W, Microstructures and wear resistance of the argon arc clad nickel-based composites on titanium alloy [J]. Surf Rev Lett 26 (08), (2018) 1950047. https://doi.org/10.1142/s0218625x19500471
Liu Y H, Li J, and Xuan F Z, Fabrication of TiC reinforced Ni based coating by laser cladding [J]. Surf Eng 28 (2012) 560–563. https://doi.org/10.1179/1743294412y.0000000026
Wang C Q, Wang L J, Wu J Q, Chen Z Z, and Niu Y J, LaF3 Influences on wear resistance of TiC/Ni cladding layer by laser cladding in-situ fabricated [J]. Adv Mater Res 549 (2012) 335–339. https://doi.org/10.4028/www.scientific.net/AMR.549.335
Wang Y D, Yu X Y, and Liu X, Analysis of in-situ TiC/TiN reinforced nickel-based composite coating by argon arc cladding [J]. Special Casting Nonferrous Alloys 34 (2014) 420–422.
Yang H Y, Du X D, and Wang J F, Study on microstructure and properties of WC particle reinforced composite coating prepared by argon arc cladding [J]. Spec Cast Nonferrous Alloys 30 (2010) 856–858.
Ouyang J H, Li X D, and Lei T C, Electron microscopy structure study of laser-clad TiC-Ni particle-reinforced coating [J]. J Mater Eng Perform 9 (2000) 234–246. https://doi.org/10.1361/105994900770346204
Hu J K, Liu Y, Zhao X Y, Xie Y X, and Li W, Effects of TiC/CeO2 addition on microstructure and wear resistance of Ni-based composite coatings fabricated by laser cladding on H13 steel [J]. Appl Phys A (2019). https://doi.org/10.1007/s00339-018-2328-4
Li D M, Sun X F, Li Z M, Song W, and Zheng B J, Effect of TiC content on the microstructure and properties of large-area laser-cladded TiC Ni-based composite coatings [J]. Mater Res Express 8 (2021) 026516. https://doi.org/10.1088/2053-1591/abe54e
Xu J, Liu W J, and Zhong M L, Microstructure and dry sliding wear behavior of MoS2/TiC/Ni composite coatings prepared by laser cladding [J]. Surf Coat Technol 200 (2006) 4227–4232. https://doi.org/10.1016/j.surfcoat.2005.01.036
Wang J Y, Wang W Z, and Jia J H, The oxidation resistance and tribological properties of Ni-based composites with in situ/ex situ Al2O3 and TiC ceramic phases at high temperatures [J]. Journal of Materials Research 31 (2016) 3262–3271. https://doi.org/10.1557/jmr.2016.350
Liu Y F, Feng Z C, Pu F, and Xia Z Y, Microstructure and dry-sliding wear properties of TiC/CaF2/γ-Ni self-lubricating wear-resistant composite coating produced by co-axial powder feeding plasma transferred arc (PTA) cladding process [J]. Surf Coat Technol 345 (2018) 61–69. https://doi.org/10.1016/j.surfcoat.2018.04.003
Tian H Y, Zhu D, Qu N S, and Zhu Z W, Wear resistance of nano-Al2O3 particle reinforced nickel-based composite coating prepared by electrophoretic-electroplating deposition [J]. Mech Eng Mater. 03 (2009) 65–71.
Li G J, Li J, and Luo X, Effects of post-heat treatment on microstructure and properties of laser cladded composite coatings on titanium alloy substrate [J]. Opt Laser Technol 65 (2015) 66–75. https://doi.org/10.1016/j.optlastec.2014.07.003
Kumar A, and Das A K, Development of Al-Ni-TiC composite coating on commercially pure al using tungsten inert gas welding route and its wear behavior [J]. J Mater Eng Perform 31 (2022) 5324–5331. https://doi.org/10.1007/s11665-022-06662-2
Zhang L Z, Zhao Z Y, Bai P K, Du W B, and Huo P C, Microstructure and properties of in situ synthesized TiC/Graphene/Ti6Al4V composite coating by laser cladding [J]. Trans Indian Inst of Metal 74 (2021) 891–899. https://doi.org/10.1007/s12666-020-02149-7
Xuan H F, Wang Q Y, Bai S L, Liu Z D, and Yan P C, A study on microstructure and flame erosion mechanism of a graded Ni–Cr–B–Si coating prepared by laser cladding [J]. Surf Coat Technol 244 (2014) 203–209. https://doi.org/10.1016/j.surfcoat.2014.02.021
Yu T, Deng Q L, Dong G, and Yang J Q, Effects of Ta on microstructure and microhardness of Ni based laser clad coating [J]. Appl Surf Sci 257 (2011) 5098–5103. https://doi.org/10.1016/j.apsusc.2011.01.027
He X, Song R G, and Kong D J, Effects of TiC on the microstructure and properties of TiC/TiAl composite coating prepared by laser cladding [J]. Opt Laser Technol 112 (2019) 339–348. https://doi.org/10.1016/j.optlastec.2018.11.037
Acknowledgements
This research work is supported by Sichuan Province Shale Gas Efficient Exploitation Advanced Material Preparation Technology Engineering Research Center, which belongs to the innovation fund project (2022SCYYQKCCL013).
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare no competing interests.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Lv, D., Tian, L., Wang, L. et al. Microstructure and Wear Resistance Analysis of TiC/Ni Composite Coating on P110 Steel by Argon Arc Cladding. Trans Indian Inst Met (2024). https://doi.org/10.1007/s12666-024-03302-2
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s12666-024-03302-2