Skip to main content
SpringerLink
Log in

In-depth analysis of the fatigue mechanism induced by inclusions for high-strength bearing steels

  • Published:
International Journal of Minerals, Metallurgy and Materials Aims and scope Submit manuscript

Abstract

A numerical study of stress distribution and fatigue behavior in terms of the effect of voids adjacent to inclusions was conducted with finite element modeling simulations under different assumptions. Fatigue mechanisms were also analyzed accordingly. The results showed that the effects of inclusions on fatigue life will distinctly decrease if the mechanical properties are close to those of the steel matrix. For the inclusions, which are tightly bonded with the steel matrix, when the Young’s modulus is larger than that of the steel matrix, the stress will concentrate inside the inclusion; otherwise, the stress will concentrate in the steel matrix. If voids exist on the interface between inclusions and the steel matrix, their effects on the fatigue process differ with their positions relative to the inclusions. The void on one side of an inclusion perpendicular to the fatigue loading direction will aggravate the effect of inclusions on fatigue behavior and lead to a sharp stress concentration. The void on the top of inclusion along the fatigue loading direction will accelerate the debonding between the inclusion and steel matrix.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. P. Rycerz, A. Olver, and A. Kadiric, Propagation of surface initiated rolling contact fatigue cracks in bearing steel, Int. J. Fatigue, 97(2017), p. 29.

    Article  CAS  Google Scholar 

  2. C. Gu, Y.P. Bao, P. Gan, M. Wang, and J.S. He, Effect of main inclusions on crack initiation in bearing steel in the very high cycle fatigue regime, Int. J. Miner. Metall. Mater., 25(2018), No. 6, p. 623.

    Article  CAS  Google Scholar 

  3. N.K. Arakere, Gigacycle rolling contact fatigue of bearing steels: A review, Int. J. Fatigue, 93(2016), p. 238.

    Article  CAS  Google Scholar 

  4. K. Shiozawa and L. Lu, Very high-cycle fatigue behaviour of shot-peened high-carbon-chromium bearing steel, Fatigue Fract. Eng. Mater. Struct., 25(2002), No. 8–9, p. 813.

    Article  CAS  Google Scholar 

  5. C. Bathias and P.C. Paris, Gigacycle Fatigue in Mechanical Practice, CRC Press, Boca Raton, 2004.

    Book  Google Scholar 

  6. U. Krupp, K. Koschella, and A. Giertler, The significance of grain size, segregations and inclusions for the very high cycle fatigue (VHCF) behavior of tempered martensitic steels, Procedia Struct. Integrity, 23(2019), p. 517.

    Article  Google Scholar 

  7. H.Y. Zheng, S.Q. Guo, M.R. Qiao, L.B. Qin, X.J. Zou, and Z.M. Ren, Study on the modification of inclusions by Ca treatment in GCr18Mo bearing steel, Adv. Manuf., 7(2019), No. 4, p. 438.

    Article  CAS  Google Scholar 

  8. W.J. Ma, Y.P. Bao, M. Wang, and D.W. Zhao, Influence of slag composition on bearing steel cleanness, Ironmaking Steelmaking, 41(2014), No. 1, p. 26.

    Article  CAS  Google Scholar 

  9. W. Xiao, M. Wang, and Y.P. Bao, The research of low-oxygen control and oxygen behavior during RH process in silicondeoxidization bearing steel, Metals, 9(2019), No. 8, art. No. 812.

  10. H.F. Xu, F. Yu, C. Wang, W.L. Zhang, J. Li, and W.Q. Cao, Comparison of microstructure and property of high chromium bearing steel with and without nitrogen addition, J. Iron Steel Res. Int., 24(2017), No. 2, p. 206.

    Article  Google Scholar 

  11. Y. Xu, E.G. Wang, Z. Li, and A.Y. Deng, Effects of vertical electromagnetic stirring on grain refinement and macrosegregation control of bearing steel billet in continuous casting, J. Iron Steel Res. Int., 24(2017), No. 5, p. 483.

    Article  Google Scholar 

  12. B. Shahriari, R. Vafaei, E.M. Sharifi, and K. Farmanesh, Aging behavior of a copper-bearing high-strength low-carbon steel, Int. J. Miner. Metall. Mater., 25(2018), No. 4, p. 429.

    Article  CAS  Google Scholar 

  13. S.X. Li, Effects of inclusions on very high cycle fatigue properties of high strength steels, Int. Mater. Rev., 57(2012), No. 2, p. 92.

    Article  CAS  Google Scholar 

  14. A. Pineau and S. Forest, Effects of inclusions on the very high cycle fatigue behaviour of steels, Fatigue Fract. Eng. Mater. Struct., 40(2017), No. 11, p. 1694.

    Article  CAS  Google Scholar 

  15. T. Sakai, Y. Sato, and N. Oguma, Characteristic S−N properties of high — carbon-chromium — bearing steel under axial loading in long — life fatigue, Fatigue Fract. Eng. Mater. Struct., 25(2002), No. 8–9, p. 765.

    Article  CAS  Google Scholar 

  16. T. Sakai, M. Takeda, K. Shiozawa, Y. Ochi, M. Nakajima, T. Nakamura, and N. Oguma, Experimental reconfirmation of characteristic S−N property for high carbon chromium bearing steel in wide life region in rotating bending, J. Soc. Mater. Sci. Jpn., 49(2000), No. 7, p. 779.

    Article  CAS  Google Scholar 

  17. H. Matsunaga, C. Sun, Y. Hong, and Y. Murakami, Dominant factors for very-high-cycle fatigue of high-strength steels and a new design method for components, Fatigue Fract. Eng. Mater. Struct., 38(2015), No. 11, p. 1274.

    Article  Google Scholar 

  18. U. Karr, Y. Sandaiji, R. Tanegashima, S. Murakami, B. Schönbauer, M. Fitzka, and H. Mayer, Inclusion initiated fracture in spring steel under axial and torsion very high cycle fatigue loading at different load ratios, Int. J. Fatigue, 134(2020), art. No. 105525.

  19. G.H. Gao, Q.Z. Xu, H.R. Guo, X.L. Gui, B.X. Zhang, and B.Z. Bai, Effect of inclusion and microstructure on the very high cycle fatigue behaviors of high strength bainite/martensite multiphase steels, Mater. Sci. Eng. A, 739(2019), p. 404.

    Article  CAS  Google Scholar 

  20. D. Spriestersbach, P. Grad, and E. Kerscher, Influence of different non-metallic inclusion types on the crack initiation in high-strength steels in the VHCF regime, Int. J. Fatigue, 64(2014), p. 114.

    Article  CAS  Google Scholar 

  21. F.P.E. Dunne, A.J. Wilkinson, and R. Allen, Experimental and computational studies of low cycle fatigue crack nucleation in a polycrystal, Int. J. Plast., 23(2007), No. 2, p. 273.

    Article  CAS  Google Scholar 

  22. D.L. McDowell and F.P.E. Dunne, Microstructure-sensitive computational modeling of fatigue crack formation, Int. J. Fatigue, 32(2010), No. 9, p. 1521.

    Article  CAS  Google Scholar 

  23. W.D. Musinski and D.L. McDowell, Simulating the effect of grain boundaries on microstructurally small fatigue crack growth from a focused ion beam notch through a three-dimensional array of grains, Acta Mater., 112(2016), p. 20.

    Article  CAS  Google Scholar 

  24. C.P. Przybyla and D.L. McDowell, Microstructure-sensitive extreme value probabilities for high cycle fatigue of Ni-base superalloy IN100, Int. J. Plast., 26(2010), No. 3, p. 372.

    Article  CAS  Google Scholar 

  25. C.P. Przybyla, W.D. Musinski, G.M. Castelluccio, and D.L. McDowell, Microstructure-sensitive HCF and VHCF simulations, Int. J. Fatigue, 57(2013), p. 9.

    Article  CAS  Google Scholar 

  26. G.M. Castelluccio and D.L. McDowell, Microstructure-sensitive small fatigue crack growth assessment: Effect of strain ratio, multiaxial strain state, and geometric discontinuities, Int. J. Fatigue, 82(2016), p. 521.

    Article  CAS  Google Scholar 

  27. R. Prasannavenkatesan, J.X. Zhang, D.L. McDowell, G.B. Olson, and H.J. Jou, 3D modeling of subsurface fatigue crack nucleation potency of primary inclusions in heat treated and shot peened martensitic gear steels, Int. J. Fatigue, 31(2009), No. 7, p. 1176.

    Article  CAS  Google Scholar 

  28. K. Gillner, M. Henrich, and S. Münstermann, Numerical study of inclusion parameters and their influence on fatigue lifetime, Int. J. Fatigue, 111(2018), p. 70.

    Article  Google Scholar 

  29. K. Gillner and S. Münstermann, Numerically predicted high cycle fatigue properties through representative volume elements of the microstructure, Int. J. Fatigue, 105(2017), p. 219.

    Article  Google Scholar 

  30. N. Vajragupta, P. Wechsuwanmanee, J. Lian, M. Sharaf, S. Münstermann, A. Ma, A. Hartmaier, and W. Bleck, The modeling scheme to evaluate the influence of microstructure features on microcrack formation of DP-steel: The artificial microstructure model and its application to predict the strain hardening behavior, Comput. Mater. Sci., 94(2014), p. 198.

    Article  CAS  Google Scholar 

  31. C. Gu, J.H. Lian, Y.P. Bao, Q.G. Xie, and S. Münstermann, Microstructure-based fatigue modelling with residual stresses: Prediction of the fatigue life for various inclusion sizes, Int. J. Fatigue, 129(2019), art. No. 105158.

  32. C. Gu, J.H. Lian, Y.P. Bao, and S. Münstermann, Microstructure-based fatigue modelling with residual stresses: Prediction of the microcrack initiation around inclusions, Mater. Sci. Eng. A, 751(2019), p. 133.

    Article  CAS  Google Scholar 

  33. W.Q. Liu, J.H. Lian, N. Aravas, and S. Münstermann, A strategy for synthetic microstructure generation and crystal plasticity parameter calibration of fine-grain-structured dual-phase steel, Int. J. Plast., 126(2020), art. No. 102614.

  34. Q.G. Xie, J.H. Lian, J.J. Sidor, F.W. Sun, X.C. Yan, C.Y. Chen, T.K. Liu, W.J. Chen, P. Yang, K. An, and Y.D. Wang, Crystallographic orientation and spatially resolved damage in a dispersion-hardened Al alloy, Acta Mater., 193(2020), p. 138.

    Article  CAS  Google Scholar 

  35. C. Gu, M. Wang, Y.P. Bao, F.M. Wang, and J.H. Lian, Quantitative analysis of inclusion engineering on the fatigue property improvement of bearing steel, Metals, 9(2019), No. 4, p. 476.

    Article  CAS  Google Scholar 

  36. Q.G. Xie, J.H. Lian, F.W. Sun, B. Gan, and Y.D. Wang, The lattice strain ratio in characterizing the grain-to-grain interaction effect and its specific insight on the plastic deformation of polycrystalline materials, J. Strain Anal. Eng. Des., 53(2018), No. 5, p. 353.

    Article  Google Scholar 

  37. Q. Xie, A.V. Bael, Y.G. An, J. Lian, and J.J. Sidor, Effects of the isotropic and anisotropic hardening within each grain on the evolution of the flow stress, the r-value and the deformation texture of tensile tests for AA6016 sheets, Mater. Sci. Eng. A, 721(2018), p. 154.

    Article  CAS  Google Scholar 

  38. D. Brooksbank and K.W. Andrews, Tessellated stresses associated with some inclusions in steel, J. Iron Steel Inst., 207(1969), p. 474.

    Google Scholar 

  39. D. Brooksbank and K.W. Andrews, Thermal expansion of some inclusions found in steels and relation to tessellated stresses, J. Iron Steel Inst., 206(1968), p. 595.

    CAS  Google Scholar 

Download references

Acknowledgements

This work was financially supported by the Fundamental Research Funds for the Central Universities (No. FRF-TP-20-026A1), the China Postdoctoral Science Foundation (No. 2020M680348), and the State Key Laboratory of Advanced Metallurgy Foundation of China (No. 41620001).

Author information

Authors and Affiliations

  1. State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing, Beijing, 100083, China

    Chao Gu & Yan-ping Bao

  2. Department of Mechanical Engineering, Aalto University, Puumiehenkuja 3, 02150, Espoo, Finland

    Wen-qi Liu & Jun-he Lian

Authors
  1. Chao Gu
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Wen-qi Liu
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Jun-he Lian
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Yan-ping Bao
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Yan-ping Bao.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Gu, C., Liu, Wq., Lian, Jh. et al. In-depth analysis of the fatigue mechanism induced by inclusions for high-strength bearing steels. Int J Miner Metall Mater 28, 826–834 (2021). https://doi.org/10.1007/s12613-020-2223-9

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s12613-020-2223-9

Keywords

Search

Navigation