Skip to main content
SpringerLink
Log in

Biofibers in polymer matrixes: an application for auto body fender

  • Research Article
  • Published:
International Journal of Plastics Technology

Abstract

The response of plantain fiber reinforced high density polyethylene composites was evaluated to assess the possibility of using it as a new material in design of auto body fender. The composite samples were prepared by injection molding and kept at room temperature for 48 h prior to testing in order to promote relaxation of stresses. Taguchi Robust Design and Finite Element Methods were applied to optimize the tensile strength, flexural strength, hardness strength and impact strength of plantain fiber reinforced high density polyethylene composites (PFRHDPE). These properties were determined at various manufacturing conditions and fiber configuration. Tensile, flexural, hardness and impact tests were conducted on replicated samples using Archimedes principles in each case to determine the volume fraction of fibers. The Taguchi robust design technique was applied for the greater the better to obtain the highest signal-to-noise ratio (SNratio) for quality characteristics (strengths) in the determination of optimum factor control levels. The Finite element method was applied in the evaluation of stress distribution and prediction of material failure zones. The overall results suggest that a natural plantain fiber reinforced composites could be utilized in automotive structural components such as fenders, bumper beams, front end modules and also in interiors of automobiles.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19
Fig. 20
Fig. 21
Fig. 22
Fig. 23
Fig. 24
Fig. 25

Similar content being viewed by others

References

  1. Jambor A, Beyer M (1997) New cars—new materials. Mater Des 18(4–6):203–209

    Article  CAS  Google Scholar 

  2. International news–ULSAB (1996) Consortium unveils the new look of ultralight steel auto body. Mater Des 17:107–110

    Google Scholar 

  3. Carle D, Blount G (1999) The suitability of aluminum as an alternative material for car bodies. Mater Des 20:267–272

    Article  CAS  Google Scholar 

  4. Sanadi AR, Caulfield DF, Rowell RM (1994) Reinforcing polyethylene with natural fibers. Plast Eng 4:27

    Google Scholar 

  5. Robinson JC (1996) Banana and Plantain. CAB International, Wallingford, p 238

    Google Scholar 

  6. Food and Agriculture Organization (1990) Production Year Book 1990. FAO, Rome

    Google Scholar 

  7. Food And Agriculture Organization (2006) Production Year Book 2006. FAO, Rome

    Google Scholar 

  8. Cheon SS, Choi JH, Lee DG (1995) Development of the composite bumper beam for passenger cars. J Comp Struct 3(2):491–499

    Article  Google Scholar 

  9. Ihueze CC, Achike MK, Okafor CE (2016) Optimal performance characteristics and reinforcement combinations of coconut fiber reinforced high density polyethylene (HDPE) polymer matrixes. J Sci Res Rep 9(3):1–10

    Google Scholar 

  10. Ihueze CC, Achike MK, Okafor CE (2016) Modelling and optimization of performance characteristics of coconut fibre particles reinforced high density polyethylene. J Basic Appl Res Int 17(1):32–48

    Google Scholar 

  11. Okafor CE, Godwin HC (2014) Evaluation of compressive and energy adsorption characteristics of natural fiber reinforced composites (NFRC). World J Eng phys Sci 2(3):036–048

    Google Scholar 

  12. Davoodi MM, Sapuan SM, Yunus R (2008) Conceptual design of a polymer Composite automotive bumper energy absorber. Mater Des 29:1447–1452

    Article  CAS  Google Scholar 

  13. Ross PJ (1993) Taguchi technique for quality engineering. Mc Graw-Hill, New York

    Google Scholar 

  14. Roy RK (1990) A primer on the Taguchi method. In: Roy RK (ed) Competitive Manufacturing Series, Van Nostrand Reinhold, New York

  15. Radharamanan R, Ansuri, AP (2001) Quality improvement of a production process using taguchi methods. In: Proceedings of institute of industrial engineers annual conference, Dallas, Texas, May 20–22, 2001, Paper Solutions

  16. Bao HP, Samareh JA (2000) Affordable design: A methodology to implement process-based manufacturing cost models into the traditional performance focused multidisciplinary design optimization. In: Proceedings of the eighth AIAA/NASA/USAF/ISSMO symposium on multidisciplinary analysis and optimization, Long Beach, California, USA, paper no. 2000–4839 (AIAA, Reston, VA, USA)

  17. Gutowski T, Hoult D, Dillon G, Neoh ET, Muter S, Kim E, Tse M (1994) Development of a theoretical cost model for advanced composite fabrication. Compos Mfg 5(4):231–239

    Google Scholar 

  18. Northrop Corporation, Advanced composites cost estimating manual (ACCEM) (1976) Technical report AFFDL-TR-76-87, Air Force Flight Dynamics Laboratory, Wright–Pattens Air Force Base Dayton, Ohio

Download references

Author information

Authors and Affiliations

  1. Department of Industrial/Production Engineering, Nnamdi Azikiwe University, Awka, Nigeria

    Christopher Chukwutoo Ihueze & Obiora Jeremiah Obiafudo

  2. Department of Mechanical Engineering, Nnamdi Azikiwe University, Awka, Nigeria

    Christian Emeka Okafor

Authors
  1. Christopher Chukwutoo Ihueze
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Obiora Jeremiah Obiafudo
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Christian Emeka Okafor
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Christian Emeka Okafor.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Ihueze, C.C., Obiafudo, O.J. & Okafor, C.E. Biofibers in polymer matrixes: an application for auto body fender. Int J Plast Technol 21, 171–193 (2017). https://doi.org/10.1007/s12588-017-9179-2

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s12588-017-9179-2

Keywords

Search

Navigation