Abstract
The Wire arc additive manufacturing (WAAM) process uses a metal plate as a substrate for part deposition. The presented work uses small pillars of cuboidal shapes arranged together to form the required deposition surface instead of a single large substrate. The post-processing of WAAM is arduous due to the need for the part removal from the substrate. The pillar-based substrate made this part removal process simpler and reduced the machining requirement. A WAAM setup was designed and developed in-house by integrating the gas metal arc welding (GMAW) with a three-dimensional gantry. The setup was utilised to deposit thin-walled metal parts over the pillar-based substrate. The online recorded temperature at the base using thermocouples confirmed adequate cooling between subsequent layers. The temperature of the pillar-based substrate was compared with the conventional substrate, which ensured proper heat dissipation. The microstructural study and hardness measurement of the deposited parts also confirmed that the pillar-based substrate has little effect on the part quality. The applications of the pillar-based substrate were further extended to demonstrate the deposition of multiple parts on a single substrate and part containing non-planar layers (overhanging features).
Similar content being viewed by others
References
Lee, C. M., Woo, W. S., Baek, J. T., & Kim, E. J. (2016). Laser and arc manufacturing processes: A review. International Journal of Precision Engineering and Manufacturing, 17(7), 973–985. https://doi.org/10.1007/s12541-016-0119-4
Jinoop, A. N., Subbu, S. K., Paul, C. P., & Palani, I. A. (2019). Post-processing of laser additive manufactured inconel 718 using laser shock peening. International Journal of Precision Engineering and Manufacturing, 20(9), 1621–1628. https://doi.org/10.1007/s12541-019-00147-4
Kim, J., Lee, W. J., & Park, H. W. (2016). The state of the art in the electron beam manufacturing processes. International Journal of Precision Engineering and Manufacturing, 17(11), 1575–1585. https://doi.org/10.1007/s12541-016-0184-8
Ha, S., Park, E., & Kim, N. (2020). Analysis of shape deformation from densification of additive manufacturing parts in selective laser sintering. International Journal of Precision Engineering and Manufacturing, 21(8), 1571–1580. https://doi.org/10.1007/s12541-020-00359-z
Lee, C. M., Woo, W. S., Kim, D. H., Oh, W. J., & Oh, N. S. (2016). Laser-assisted hybrid processes: A review. International Journal of Precision Engineering and Manufacturing, 17(2), 257–267. https://doi.org/10.1007/s12541-016-0034-8
Ding, D., Pan, Z., Cuiuri, D., & Li, H. (2015). Wire-feed additive manufacturing of metal components: Technologies, developments and future interests. International Journal of Advanced Manufacturing Technology, 81(1–4), 465–481. https://doi.org/10.1007/s00170-015-7077-3
Wang, Z., Jing, T., & Dong, H. (2019). Phase field study of spacing evolution during wire and laser additive manufacturing under transient conditions. IOP Conference Series Materials Science and Engineering. https://doi.org/10.1088/1757-899X/529/1/012003
Nie, Z., Wang, G., McGuffin-Cawley, J. D., Narayanan, B., Zhang, S., Schwam, D., & Rong, Y. (2016). Experimental study and modeling of H13 steel deposition using laser hot-wire additive manufacturing. Journal of Materials Processing Technology, 235, 171–186. https://doi.org/10.1016/j.jmatprotec.2016.04.006
Wu, B., Pan, Z., Ding, D., Cuiuri, D., Li, H., Xu, J., & Norrish, J. (2018). A review of the wire arc additive manufacturing of metals: Properties, defects and quality improvement. Journal of Manufacturing Processes, 35, 127–139. https://doi.org/10.1016/j.jmapro.2018.08.001
Montevecchi, F., Venturini, G., Grossi, N., Scippa, A., & Campatelli, G. (2018). Idle time selection for wire-arc additive manufacturing: A finite element-based technique. Additive Manufacturing, 21, 479–486. https://doi.org/10.1016/j.addma.2018.01.007
Xiong, J., Lei, Y., Chen, H., & Zhang, G. (2017). Fabrication of inclined thin-walled parts in multi-layer single-pass GMAW-based additive manufacturing with flat position deposition. Journal of Materials Processing Technology, 240, 397–403. https://doi.org/10.1016/j.jmatprotec.2016.10.019
Panchagnula, J. S., & Simhambhatla, S. (2018). Manufacture of complex thin-walled metallic objects using weld-deposition based additive manufacturing. Robotics and Computer-Integrated Manufacturing, 49, 194–203. https://doi.org/10.1016/j.rcim.2017.06.003
Ding, D., Pan, Z., Cuiuri, D., & Li, H. (2014). A tool-path generation strategy for wire and arc additive manufacturing. International Journal of Advanced Manufacturing Technology, 73(1–4), 173–183. https://doi.org/10.1007/s00170-014-5808-5
Abe, T., & Sasahara, H. (2015). Development of the shell structures fabrication CAM system for direct metal lamination using arc discharge-lamination height error compensation by torch feed speed control-. International Journal of Precision Engineering and Manufacturing, 16(1), 171–176. https://doi.org/10.1007/s12541-015-0022-4
Wu, B., Ding, D., Pan, Z., Cuiuri, D., Li, H., Han, J., & Fei, Z. (2017). Effects of heat accumulation on the arc characteristics and metal transfer behavior in wire arc additive manufacturing of Ti6Al4V. Journal of Materials Processing Technology, 250, 304–312. https://doi.org/10.1016/j.jmatprotec.2017.07.037
Geng, H., Li, J., Xiong, J., Lin, X., & Zhang, F. (2017). Optimization of wire feed for GTAW based additive manufacturing. Journal of Materials Processing Technology, 243, 40–47. https://doi.org/10.1016/j.jmatprotec.2016.11.027
Martina, F., Colegrove, P. A., Williams, S. W., & Meyer, J. (2015). Microstructure of interpass rolled wire + arc additive manufacturing Ti-6Al-4V components. Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, 46(12), 6103–6118. https://doi.org/10.1007/s11661-015-3172-1
Martina, F., Mehnen, J., Williams, S. W. W., Colegrove, P., & Wang, F. (2012). Investigation of the benefits of plasma deposition for the additive layer manufacture of Ti-6Al-4V. Journal of Materials Processing Technology, 212(6), 1377–1386. https://doi.org/10.1016/j.jmatprotec.2012.02.002
Venturini, G., Montevecchi, F., Scippa, A., & Campatelli, G. (2016). Optimization of WAAM deposition patterns for T-crossing features. Procedia CIRP, 55, 95–100. https://doi.org/10.1016/j.procir.2016.08.043
Azizi, A., & Schiffres, S. N. (2020). Laser metal additive manufacturing on graphite. Solid Freeform Fabrication 2018: Proceedings of the 29th Annual International Solid Freeform Fabrication Symposium - An Additive Manufacturing Conference, SFF 2018, 2315–2324.
Hildreth, O. J., Nassar, A. R., Chasse, K. R., & Simpson, T. W. (2016). Dissolvable metal supports for 3D direct metal printing. 3d Printing and Additive Manufacturing, 3(2), 91–97. https://doi.org/10.1089/3dp.2016.0013
Haselhuhn, A. S., Wijnen, B., Anzalone, G. C., Sanders, P. G., & Pearce, J. M. (2015). In situ formation of substrate release mechanisms for gas metal arc weld metal 3-D printing. Journal of Materials Processing Technology, 226, 50–59. https://doi.org/10.1016/j.jmatprotec.2015.06.038
Haselhuhn, A. S., Gooding, E. J., Glover, A. G., Anzalone, G. C., Wijnen, B., Sanders, P. G., & Pearce, J. M. (2016). Substrate release mechanisms for gas metal arc weld 3D aluminum metal printing. 3D Printing and Additive Manufacturing, 1(4), 204–209. https://doi.org/10.1089/3dp.2014.0015
Jiang, J., Xu, X., & Stringer, J. (2018). Support structures for additive manufacturing: A review. Journal of Manufacturing and Materials Processing, 2(4), 64. https://doi.org/10.3390/jmmp2040064
Kapil, S., Joshi, P., Kulkarni, P. M., Negi, S., Kumar, R., & Karunakaran, K. P. (2018). Elimination of support mechanism in additive manufacturing through substrate tilting. Rapid Prototyping Journal, 24(7), 1155–1165. https://doi.org/10.1108/RPJ-07-2017-0139
Kazanas, P., Deherkar, P., Almeida, P., Lockett, H., & Williams, S. (2012). Fabrication of geometrical features using wire and arc additive manufacture. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 226(6), 1042–1051. https://doi.org/10.1177/0954405412437126
Xia, C., Pan, Z., Polden, J., Li, H., Xu, Y., & Chen, S. (2021). Modelling and prediction of surface roughness in wire arc additive manufacturing using machine learning. Journal of Intelligent Manufacturing. https://doi.org/10.1007/s10845-020-01725-4
Cunningham, C. R., Flynn, J. M., Shokrani, A., Dhokia, V., & Newman, S. T. (2018). Invited review article: Strategies and processes for high quality wire arc additive manufacturing. Additive Manufacturing, 22(June), 672–686. https://doi.org/10.1016/j.addma.2018.06.020
Weman, K. (2012). Welding processes handbook. (2nd ed.). Woodhead Pub.
Baufeld, B., Van der Biest, O., & Gault, R. (2010). Additive manufacturing of Ti–6Al–4V components by shaped metal deposition: Microstructure and mechanical properties. Materials & Design, 31, S106–S111. https://doi.org/10.1016/J.MATDES.2009.11.032
Keehan, E., Zachrisson, J., & Karlsson, L. (2010). Influence of cooling rate on microstructure and properties of high strength steel weld metal. Science and Technology of Welding and Joining, 15(3), 233–238. https://doi.org/10.1179/136217110X12665048207692
Acknowledgement
The authors would like to thank the technical staff of the Central Workshop and the Department of Mechanical Engineering, IIT Indore, for their extended help and support. They also thank Dr Satyajit Chatterjee for allowing to access the Tribology Laboratory facilities.
Funding
This research did not receive any specific grant from funding agencies in the public, commercial, or not-for-profit sectors.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Khan, A.U., Madhukar, Y.K. Effects of Pillar-Based Substrate on the Wire Arc Additive Manufacturing Process. Int. J. Precis. Eng. Manuf. 22, 1311–1321 (2021). https://doi.org/10.1007/s12541-021-00529-7
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12541-021-00529-7