Abstract
In this paper, direct shear tests of cement mortar samples with non-persistent planar joints are reported, to study the effects of joint connectivity ratio k (ratio of the length of the planar joint to the length of the specimen) and locations of a planar joint on the shear properties of artificial jointed rock samples. The test results indicate that (a) the shear stress-shear displacement curve of samples with non-persistent planar joint under direct shear stress consists of five stages. (b) For samples with a non-persistent planar joint, when the joint connectivity ratio k remains unchanged, the shear strength of the specimen increases as the distance s between the left end of the planar joint and the left edge of the specimen increases. When the distance s remains constant, the shear strength of the specimens increases with an increase in the joint connectivity ratio k. When both the joint connectivity ratio k and the distance s remain unchanged, the shear strength increases as higher normal stress is applied. (c) For samples with two non-persistent planar joints and constant joint connectivity ratio k, the shear strength increases as the two planar joints, respectively, are at the two ends of specimen, compared to the scenario where the two planar joints are at the middle of the specimen. The results also demonstrate that the proposed fitting model is suitable for characterizing the shear stress-shear displacement of artificial jointed rock specimens where a non-persistent planar joint is present.
Similar content being viewed by others
References
Atapour H, Moosavi M (2013) Some effects of shearing velocity on the shear stress-deformation behaviour of hard-soft artificial material interfaces. Geotech Geol Eng 31:1603–1615
Bahaaddini M (2017) Effect of boundary condition on the shear behaviour of rock joints in the direct shear test. Rock Mech Rock Eng 50:1141–1155
Bahaaddini M, Sharrock G, Hebblewhite BK (2013) Numerical direct shear tests to model the shear behaviour of rock joints. Comput Geotech 51:101–115
Bahaaddini M, Hagan PC, Mitra R, Hebblewhite BK (2015) Parametric study of smooth joint parameters on the shear behaviour of rock joints. Rock Mech Rock Eng 48:923–940
Bai SW, Ren WZ, Feng DX, Zhou SH (1999) Research on the strength behaviour of rock containing coplanar close intermittent joints by direct test. Rock Soil Mech 20:10–16 [In Chinese]
Cui YF (2019) Effect of joint type on the shear behavior of synthetic rock. Bull Eng Geol Environ 78:3395–3412
Ghazvinian AH, Taghichian A, Hashemi M, Mar’ashi SA (2010) The shear behavior of bedding planes of weakness between two different rock types with high strength difference. Rock Mech Rock Eng 43:69–87
Gui Y, Xia CC, Ding WQ, Qian X, Du SG (2019) Modelling shear behaviour of joint based on joint surface degradation during shearing. Rock Mech Rock Eng 52:107–131
Gutiérrez-Ch JG, Senent S, Melentijevic S, Jimenez R (2018) Distinct element method simulations of rock-concrete interfaces under different boundary conditions. Eng Geol 240:123–139
He ZM, Xiong ZY, Hu QG, Yang M (2014) Analytical and numerical solutions for shear mechanical behaviors of structural plane. J Cent South Univ 21:2944–2949
Hu B, Zhang N, Wang SJ, Chen JS (2011) Model test and strength analysis research on intermittent joint rock mass. Chin J Undergr Space Eng 7:657–664 [In Chinese]
Hu B, Wang SJ, Liu SL (2012) Direct shear strength model of rock mass with coplanar intermittent joints. Journal of Jiangsu University (Natural Science Edition) 33:601–605 [In Chinese]
Huang JY, Xu SL, Hu SS (2014) Numerical investigations of the dynamic shear behavior of rough rock joints. Rock Mech Rock Eng 47:1727–1743
Jahanian H, Sadaghiani MH (2015) Experimental study on the shear strength of sandy clay infilled regular rough rock joints. Rock Mech Rock Eng 48:907–922
Lajtai EZ (1969a) Shear strength of weakness planes in rock. Int J Rock Mech Min Sci Geomech Abstr 6:499–515
Lajtai EZ (1969b) Strength of discontinuous rocks in direct shear. Geotechnique 19:218–233
Lee SW, Jeong DW, Lee SW, Lee SW (2014) Influence of asperity characteristics on plane interface shear behavior. KSCE J Civ Eng 18:742–750
Liu YM, Liu J, Xia CC (2014) Research on strength behavior of rock mass containing discontinuous joints by direct shear test under different joint surface morphologies. Rock Soil Mech 35:1269–1274 [In Chinese]
Meng FZ, Zhou H, Wang ZQ, Zhang LM, Kong L, Li SJ, Zhang CQ, Hu SC (2017) Experimental study of factors affecting fault slip rockbursts in deeply buried hard rock tunnels. Bull Eng Geol Environ 76:1167–1182
Park JW, Song JJ (2009) Numerical simulation of a direct shear test on a rock joint using a bonded-particle model. Int J Rock Mech Min Sci 46:1315–1328
Sadegh Asadi M, Rasouli V, Barla G (2012) A bonded particle model simulation of shear strength and asperity degradation for rough rock fractures. Rock Mech Rock Eng 45:649–675
Shen MR, Zhang QZ (2010) Experimental study of shear deformation characteristics of rock mass discontinuities. Chin J Rock Mech Eng 29:713–719 [In Chinese]
Shen T, Feng DX, Ren WZ, Bai SW (1999) Research on strength property of shear plane including discontinuity and rock bridge. Rock Soil Mech 20:33–38 [In Chinese]
Tang ZC, Xia CC, Ding ZZ (2011) Analysis of shear deformation law for intermittent jointed rock mass. Rock Soil Mech 32:2353–2358 [In Chinese]
Tian YC, Liu QS, Ma H, Liu Q, Deng PH (2018) New peak shear strength model for cement filled rock joints. Eng Geol 233:269–280
Xia CC, Xiao WM, Liu YM (2010) Study of mechanical model for weakening process of discontinous joint rock bridge. Rock Soil Mech 29:1538–1545 [In Chinese]
Xue FG, Julian PS, Chris MH (2003) Direct shear test of sandstone-concrete joints. Int J Geomech 3:21–33
Yang XX, Kulatilake PHSW (2019) Laboratory investigation of mechanical behavior of granite samples containing discontinuous joints through direct shear tests. Arab J Geosci 12:79
Zhang XB, Jiang QH, Chen N, Wei W, Feng XX (2016) Laboratory investigation on shear behavior of rock joints and a new peak shear strength criterion. Rock Mech Rock Eng 49:3495–3512
Zhang XB, Jiang QH, Kulatilake PHSW, Xiong F, Yao C, Tang ZC (2019) Influence of asperity morphology on failure characteristics and shear strength properties of rock joints under direct shear tests. Int J Geomech 19:04018196(1)–04018196(13)
Zhou H, Meng FZ, Zhang CQ, Lu JJ, Xu RC (2015) Experimental study on effect of joints with different locations and sizes on rock failure. Chin J Rock Mech Eng 34:3018–3028 [In Chinese]
Funding
This work was supported by the Systematic Project of Guangxi Key Laboratory of Disaster Prevention and Engineering Safety (Grant No. 2019ZDK051), the Open Research Fund of State Key Laboratory of Simulation and Regulation of Water Cycle in River Basin (China Institute of Water Resources and Hydropower Research, Grant No. IWHR-SKL-201708), and the Project of State Key Laboratory of Geohazard Prevention and Geoenvironment Protection (Grant No. SKLGP2018Z020).
Author information
Authors and Affiliations
Corresponding author
Additional information
Responsible Editor: Zeynal Abiddin Erguler
Rights and permissions
About this article
Cite this article
Xiong, L., Chen, H., Geng, X. et al. Influence of joint location and connectivity on the shear properties of artificial rock samples with non-persistent planar joints. Arab J Geosci 13, 565 (2020). https://doi.org/10.1007/s12517-020-05589-z
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s12517-020-05589-z