Abstract
Spinal posture including thorax/pelvis orientations as well as loads on the intervertebral discs are crucial parameters in biomechanical models and ergonomics to evaluate the risk of low back injury. In vivo measurement of spinal posture toward estimation of spine loads requires the common motion capture techniques and laboratory instruments that are costly and time-consuming. Hence, a closed loop algorithm including an artificial neural network (ANN) and fuzzy logic is proposed here to predict the L5–S1 segment loads and thorax/pelvis orientations in various 3D reaching activities. Two parts namely a fuzzy logic strategy and an ANN from this algorithm; the former, developed based on the measured postures of 20 individuals, is to determine 3D orientations of the thorax/pelvis during the various activities while the latter, developed based on the predicted L5–S1 loads by a detailed musculoskeletal model of the spine, is to estimate compression/shear forces at the L5–S1 disc. The fuzzy logic rules are extracted based on Sugeno inference engine and the ANN is trained by LevenbergMarquardt algorithm. To evaluate the performance of the proposed strategy, the comparison between the predicted values, the target values and the presented values in the literature are reviewed. The comparison demonstrated that the proposed algorithm had a promising performance. The maximum relative error for all predictions was ~19 % and with respect to the target values while this error for the literature’s values was ~37 %. Also, the average improvement of the proposed strategy was ~17 % with respect to the presented strategy in the literature.
Similar content being viewed by others
References
N. Arjmand and A. Shirazi-Adl, Model and in vivo studies on human trunk load partitioning and stability in isometric forward flexions, Journal of Biomechanics, 39 (2006) 510–521.
C. Fortin, D. E. Feldman, F. Cheriet and H. Labelle, Validity of a quantitative clinical measurement tool of trunk posture in idiopathic scoliosis, Spine, 35 (2010) 988–994.
L. X. Guo and R. Li, Influence of vibration frequency variation on poroelastic response of intervertebral disc of lumbar spine, Journal of Mechanical Science and Technology, 33(2) (2019) 973–979.
Y. H. Kim, B. Khuyagbaatar and K. Kim, Recent advances in finite element modeling of the human cervical spine, Journal of Mechanical Science and Technology, 32(1) (2018) 1–10.
Z. Merrill, G. Bova, A. Chambers and R. Cham, Effect of trunk segment boundary definitions on frontal plane segment inertial calculations, Journal of Applied Biomechanics, 34 (2018) 232–235.
M. J. Dysart and J. C. Woldstad, Posture prediction for static sagittal-plane lifting, Journal of Biomechanics, 29 (1996) 1393–1397.
M. A. Perez and M. A. Nussbaum, A neural network model for predicting postures during non-repetitive manual materials handling tasks, Ergonomics, 51 (2008) 1549–1564.
B. Zhang, I. Horváth, J. F. M. Molenbroek and C. Snijders, Using artificial neural networks for human body posture prediction, International Journal of Industrial Ergonomics, 40 (2010) 414–424.
A. Gholipour and N. Arjmand, Artificial neural networks to predict 3D spinal posture in reaching and lifting activities; Applications in biomechanical models, Journal of Biomechanics, 49 (2016) 2946–2952.
N. Arjmand, A. Plamondon, A. Shirazi-Adl, C. Larivière and M. Parnianpour, Predictive equations to estimate spinal loads in symmetric lifting tasks, Journal of Biomechanics, 44 (2011) 84–91.
H. Sayyaadi and S. H. Zareh, Intelligent control of an MR prosthesis knee using of a hybrid self-organizing fuzzy controller and multidimensional wavelet NN, Journal of Mechanical Science and Technology, 31 (2017) 3509–3518.
F. Cavallaro and A. Fausto, Takagi-Sugeno fuzzy inference system for developing a sustainability index of biomass, Sustainability, 7 (2015) 1259–1271.
S. H. Zareh, A. Sarrafan, A. A. A. Khayyat and A. Zabihollah, Intelligent semi-active vibration control of eleven degrees of freedom suspension system using magnetorheological dampers, Journal of Mechanical Science and Technology, 26(2) (2012) 323–334.
Acknowledgments
The work was supported from Technical and Vocational University and Sharif University of Technology.
Author information
Authors and Affiliations
Corresponding author
Additional information
Recommended by Editor Sehyun Shin
Seiyed Hamid Mousavi received his Ph.D. degree from the Sharif University of Technology, Tehran, Iran, in 2016. He was postdoctoral fellow at the School Mechanical Engineering, Sharif University of Technology from 2017 to 2018. Dr. Mousavi is currently an Assistant Professor at the Technical and Vocational University, Tehran Branch, Iran. He published more than thirty research papers. His research interests are vibration, intelligent control, ventilation, smart materials and structures.
Hassan Sayyaadi received his B.Sc. degree from the Amir Kabir University of Technology in 1987 and M.Sc. degree from the Sharif University of Technology, Tehran, Iran, in 1990 and the Ph.D. degree from the University of Tokyo, Japan, in 2001 all in Mechanical Engineering. Dr. Sayyaadi is currently a Professor at the School of Mechanical Engineering, Sharif University of Technology, Tehran, Iran. He published more than one hundred research papers. His research interests are robotics, intelligent control, smart materials and vibration.
Navid Arjmand received his B.Sc. degree from the Iran University of Science and Technology in 1998 and M.Sc. degree from the Sharif University of Technology, Tehran, Iran, in 2001 and the Ph.D. degree from the Ecole Polytechnique de Montreal, Canada, in 2006 all in Mechanical Engineering. Dr. Arjmand is currently an Associate Professor at the School of Mechanical Engineering, Sharif University of Technology, Tehran, Iran. He published more than one hundred research papers. His research interests are spine biomechanics, FEM and ergonomics.
Rights and permissions
About this article
Cite this article
Mousavi, S.H., Sayyaadi, H. & Arjmand, N. Prediction of the thorax/pelvis orientations and L5–S1 disc loads during various static activities using neuro-fuzzy. J Mech Sci Technol 34, 3481–3485 (2020). https://doi.org/10.1007/s12206-020-0740-0
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12206-020-0740-0