Abstract
This paper presents an analysis of seismically isolated buildings using fiber-reinforced elastomeric structures that are subject to excitations caused by earthquakes. In analyzing the vibrations, the buildings are modeled by lumped mass systems. The fundamental equations of motion are derived for base isolated structures, and the hysteretic and nonlinear- elastic characteristics are included in the numerical calculations. The earthquake waves used as the excitation forces are those that have been recorded during strong earthquake motions in order to examine the dynamic stability of building structures. The seismic (nonlinear) responses of the building are compared for each restoring force type and, as a result, it is shown that the building’s motions are not so large from a seismic design standpoint. Isolating structures are shown to reduce the responses sufficiently allowing the building’s motions to be controlled to within a practical range. By increasing the acceleration of the earthquake, the yielding forces in the concrete and steel frames can be determined, which shows the advantages of performing nonlinear dynamic analysis in such applications.
Similar content being viewed by others
References
J. M. Kelly, Seismic isolation of civil buildings in the USA, Progress in Structural Engineering and Materials, 1(3) (1998) 279–285.
A. Martelli and M. Forni, Seismic isolation of civil buildings in Europe, Progress in Structural Engineering and Materials, 1(3) (1998) 286–294.
T. Fujita, Seismic isolation of civil buildings in Japan, Progress in Structural Engineering and Materials, 1(3) (1998) 295–300.
J. M. Kelly, Earthquake-resistant design with rubber, Second Ed. Springer, London, U.K., (1997).
J. M. Kelly, Analysis of fiber-reinforced elastomeric isolators. J. Seismol. Earthquake Eng., 2(1) (1999) 19–34.
B. Y. Moon, G. J. Kang, B. S. Kang and J. M. Kelly, Design and manufacturing of fiber reinforced elastomeric isolator for seismic isolation, J. Mater. Process. Technol, 130/131 (2002) 145–150.
B. S. Kang, G. J. Kang and B. Y. Moon, Hole and lead plug effect on fiber reinforced elastomeric isolator for seismic isolation, J. Mater. Process. Technol., 140 (2003) 592–597.
J. M. Kelly, Analysis for fiber-reinforced elastomeric isolators. Annual Report to Engineering Research Center for Net-Shape and Die Manufacturing Pusan National University Korea. (2000).
B. Y. Moon, G. J. Kang, B. S. Kang and K. S. Kim, Design and experimental analysis of fiber reinforced elastomeric isolator, Transactions of the KSME, A., 26(10) (2002) 2026–2033.
Author information
Authors and Affiliations
Corresponding author
Additional information
This paper was recommended for publication in revised form by Associate Editor Dae-Eun Kim
Gyung-Ju Kang received a B.S., M.S. and Ph.D degrees in Aerospace Engineering from Pusan National Univer-sity, Korea, in 1997, 1999 and 2005, respectively. Dr. Kang’s research interests are in the area of seismic bearing design, base isolation, cold forging, and steel structure.
Beom-Soo Kang received a B.S. degree in Mechanical Engineering from Pusan National University, Busan, Korea in 1981. He then went on to receive his M.S. degree in Aerospace Engineering from KAIST (Korea Advanced Institute of Science and Technology) Seoul, Korea, in 1983 and Ph.D. degree in Mechanical Engineering from University of California at Berkeley in 1990. Dr. Kang is currently a Professor at Department of Aero-space Engineering at Pusan National University. He is currently serving as the Director of ILIC (Industrial Liaison Innovation Cluster). Dr. Kang’s re-search interests include flexible forming, unmanned system design, multi-stage deep drawing, and cold forging.
Rights and permissions
About this article
Cite this article
Kang, G.J., Kang, B.S. Dynamic analysis of fiber-reinforced elastomeric isolation structures. J Mech Sci Technol 23, 1132–1141 (2009). https://doi.org/10.1007/s12206-008-1214-y
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12206-008-1214-y