Abstract
For practical considerations, thin-walled steel silos are often supported by a limited number of discrete equidistant supports around their circumference. In such cases, large loads are transferred to the limited number of supports, causing locally high axial compressive stress concentrations. A possible solution is to add a partial-height U-shaped longitudinal stiffener above each support. Such stiffeners create a more gradual transmission of vertical loads to the supports, increasing the maximum failure load. This paper aims to map the influence of the dimensions of such longitudinal stiffeners on the failure behaviour of a thin-walled silo. Both the parameters of the cross-section and the height of the stiffeners are discussed. All the results and the findings are based on geometrically and material nonlinear analyses — GMNA — performed with finite element software. The simulations indicate that, in general, thin-walled silos will fail by pure elastic buckling in the unstiffened silo wall above the terminations of the longitudinal stiffeners. However, this is only true if the cross-section of the stiffeners, and to a lesser degree the moment of inertia, is sufficiently large in order that the longitudinal stiffeners can absorb the supporting loads. In contrast, for longitudinal stiffeners with a small cross-section, the silo structure will fail by premature elasto-plastic collapse of the stiffeners itself at significantly lower load levels. Furthermore, the height of the stiffeners and the degree of support - the circumferential width of the supports and the stiffeners is equal to each other — are the most important geometrical parameters which are beneficial to reach a maximum load level for a specific silo. Finally, the buckling behaviour and the failure load are hardly influenced by radial width and the thickness of the longitudinal stiffeners.
Similar content being viewed by others
References
Cai, Y., Zhuang, H., and Zhu, A. (2013). “A generalized and efficient method for finite cover generation in the numerical manifold method.” International Journal of Computational Methods, Vol. 10, No. 5, pp. 1350028, DOI: 10.1142/S021987621350028X.
Chen, L. and Rotter, J. M. (2012). “Buckling of anchored cylindrical shells of uniform thickness under wind load.” Engineering Structures, Vol. 41, No. 19, pp. 199–208, DOI: http://dx.doi.org/10.1016/j.engstruct.2012.03.046.
Chen, L., Peng, Y. L., Wan, L., and Li, H. B. (2012). “Nonlinear buckling behavior of cylindrical shells of uniform thickness under wind load.” Advances in Industrial and Civil Engineering, Vol. 594–597, pp. 2753–2756, DOI: 10.4028/www.scientific.net/AMR.594-597.2753.
Dassault Systèmes (2009). Abaqus documentation version 6.9,simulia, Rhode Island, USA.
Doerich, C. (2007). Strength and stability of locally supported cylinders, PhD Thesis, Institute for Infrastructure & Environment, The School of Engineering and Electronics., University of Edinburgh, Edinburgh.
Doerich, C. (2008). “Effect of geometric nonlinearity of locally supported cylinders.” Structures and Granular Solids, Taylor & Francis, pp. 183–197.
Doerich, C. and Rotter, J. M. (2008). “Behavior of cylindrical steel shells supported on local brackets.” Journal of Structural Engineering, ASCE, Vol. 134, No. 8, pp. 1269–1277, DOI: 10.1061/(asce)0733-9445(2008)134:8(1269).
Doerich, C. and Rotter, J. M. (2011a). “Accurate determination of plastic collapse loads from finite element analyses.” Journal of Pressure Vessel Technology, ASME, Vol. 133, No. 1, DOI: 01120210.1115/1.4002770.
Doerich, C. and Rotter, J. M. (2011b). “Generalised capacity curves for stability and plasticity: Application and limitations.” Thin-Walled Structures, Vol. 49, No. 9, pp. 1132–1140, DOI: 10.1016/j.tws.2011.04.005.
Doerich, C., Vanlaere, W., Lagae, G., and Rotter, J. M. (2009). “Stability of column-supported steel cylinders with engaged columns.” Proceedings of the Symposium of the International Association for Shell and Spatial Structures IASS, Valencia.
]ECCS (2008). Buckling of steel shells: European design recommendations, 5th edition, European Convention for Constructional Steelwork, Brussels.
]EN 1993-1-6 (2006). Eurocode 3: Design of steel structures, Part 1.1 general rules for buildings, CEN, Brussels.
]EN 1993-1-6 (2007). Eurocode 3: Design of steel structures, Part 1.6: strength and stability of shell structures, CEN, Brussels.
]EN 1993-4-1 (2007). Eurocode 3: Design of steel structures, Part 4.1: Silos, CEN, Brussels.
Hubner, A., Teng, J. G., and Saal, H. (2006). “Buckling behaviour of large steel cylinders with patterned welds.” International Journal of Pressure Vessels and Piping, Vol. 83, No. 1, pp. 13–26, DOI: 10.1016/j.ijpvp.2005.10.003.
Jansseune, A. and De Corte, W. (2013). Plastic failure of locally supported silos with U-shaped longitudinal Stiffeners, ASEM 2013 Conference, Jeju, Korea.
Jansseune, A., De Corte, W., and Van Impe, R. (2013). “Columnsupported silos: Elasto-plastic failure.” Thin-Walled Structures, Vol. 73, No. 1, pp. 158–173, DOI: http://dx.doi.org/10.1016/j.tws.2013.08.005.
Jansseune, A., De Corte, W., Vanlaere, W., and Van Impe, R. (2012). “Influence of the cylinder height on the elasto-plastic failure of locally supported cylinders.” Steel and Composite Structures, Vol. 12, No. 4, pp. 291–302, DOI: 000303142400002.
Kiendl, J., Bletzinger, K. U., Linhard, J., and Wnchner, R. (2009). “Isogeometric shell analysis with Kirchhoff-Love elements.” Computer Methods in Applied Mechanics and Engineering, Vol. 198, No. 49–52, pp. 3902–3914, DOI: http://dx.doi.org/10.1016/j.cma.2009.08.013.
Nielsen, J. (2008). “From silo phenomena to load models.” Structures and Granular Solids, Taylor & Francis, pp. 49–57.
Rotter, J. M. (2004). “Cylindrical shells under axial compression.” Buckling of Thin Metal Shells. Eds: Teng, J.G. and Rotter, J.M., Spon Press, London, pp. 42–87.
Rotter, J. M. (2009). “Silos and tanks in research and practice: state of the art and current challenges.” Proceedings of the Symposium of the International Association for Shell and Spatial Structures, IASS, Valencia.
Rotter, J. M. (2011). “The new framework for shell buckling design and the european shell buckling recommendations fifth edition.” Journal of Pressure Vessel Technology-Transactions of the ASME, Vol. 133, No. 1, DOI: 01120310.1115/1.4002565.
Sadowski, A. J. and Rotter, J. M. (2011a). “Steel silos with different aspect ratios: I — Behaviour under concentric discharge.” Journal of Constructional Steel Research, Vol. 67, No. 10, pp. 1537–1544, DOI: http://dx.doi.org/10.1016/j.jcsr.2011.03.028.
Sadowski, A. J. and Rotter, J. M. (2011b). “Steel silos with different aspect ratios: II — behaviour under eccentric discharge.” Journal of Constructional Steel Research, Vol. 67, No. 10, pp. 1545–1553, DOI: http://dx.doi.org/10.1016/j.jcsr.2011.03.027.
Timoshenko, S. P. (1910). “Einige Stabilitätsprobleme der Elasticitätstheorie.” Zeitschrift für Matematic und Physik, Vol. 58, pp. 378–385.
Vanlaere, W. (2006). Buckling behaviour of stiffened cylinders on local supports, PhD Thesis, Department of Structural Engineering, Faculty of Engineering Sciences Ghent University, Ghent.
Zhuang, X., Zhu, H., and Augarde, C. (2014). “An improved meshless Shepard and least square method possessing the delta property and requiring no singular weight function.” Computational Mechanics, Vol. 53, No. 2, pp. 343–357, DOI: 10.1007/s00466-013-0912-1.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Jansseune, A., De Corte, W. & Belis, J. Elastic failure of locally supported silos with U-shaped longitudinal stiffeners. KSCE J Civ Eng 19, 1041–1049 (2015). https://doi.org/10.1007/s12205-015-0001-4
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12205-015-0001-4