Skip to main content
SpringerLink
Log in

Influence of Punch Velocity on Deformation Behavior in Deep Drawing of Aluminum Alloy

  • Technical Article---Peer-Reviewed
  • Published:
Journal of Failure Analysis and Prevention Aims and scope Submit manuscript

Abstract

Deep drawing is one of the important sheet-forming processes. Several process parameters are responsible for producing defect-free products of deep drawing. Out of those parameters, blank holder force is one of the widely studied process parameters, which significantly influence deep drawing. In the present study, the effect of velocity of the punch on deformation behavior of aluminum alloys is investigated. FEM simulation is conducted using commercially available software ABAQUS. It is found through FEM simulation that effective stress increases by nearly 56% with an increment in punch velocity from 150 to 350 mm/s. Besides this, equivalent plastic strain increases by five times on increment in punch velocity from 150 to 350 mm/s. von Mises stress and equivalent plastic strain found to be maximum at flange radii region (die corner) at all velocities of punch. Wrinkling is found to be absent during deformation (loading step) at all punch velocities. Wrinkling is obtained in deep drawn cups after unloading of the punch at all punch velocities except the lowest velocity of 150 mm/s. The phenomenon of wrinkling was found to be pronounced with increment in velocity of the punch after unloading of the punch. For prevention of wrinkling tendency during deep drawing, the velocity of punch should be less than 200 mm/s. Besides this, punch force, effective stress, and equivalent plastic strain found to increase nonlinearly due to increment in punch stroke. It is gathered through FEM simulation that wrinkling phenomenon increases with increment in punch velocity due to unloading of the punch during deep drawing.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18

Similar content being viewed by others

References

  1. S. Yoshihara, K.I. Manabe, H. Nishimura, Effect of blank holder force control in deep-drawing process of magnesium alloy sheet. J. Mater. Process. Technol. 170(3), 579–585 (2005)

    Article  CAS  Google Scholar 

  2. L.Z. Qin, W.W. Rong, C.G. Long, A new strategy to optimize variable blank holder force towards improving the forming limits of aluminum sheet metal forming. J. Mater. Process. Technol. 183(2–3), 339–346 (2007)

    Google Scholar 

  3. A. Wifi, A. Mosallam, Some aspects of blank-holder force schemes in deep drawing process. J. Achiev. Mater. Manuf. 24(1), 315–323 (2007)

    Google Scholar 

  4. P. Kováč, V. Tittel, Blank holder force optimization of hemispherical product using numerical simulation. Mater. Sci. Technol. 5, 5–10 (2010)

    Google Scholar 

  5. K. Zheng, J. Lee, J. Lin, T.A. Dean, A buckling model for flange wrinkling in hot deep drawing aluminium alloys with macro-textured tool surfaces. Int. J. Mach. Tools Manuf. 114, 21–34 (2017)

    Article  Google Scholar 

  6. O. Ozdilli, M.E. Erdin, M. Erdogan, Investigation of effects of variable blankholder force on deep drawing process of 6082 aluminum alloy. Fresenius Environ. Bull. 28(4A), 3324–3332 (2019)

    CAS  Google Scholar 

  7. D. Kumaravel, K. Venkatesh, in Reduction of Wrinkling Defect in Deep Drawing Process, Advances in Manufacturing Processes: Lecture Notes in Mechanical Engineering, K.S. Vijay Sekar, M. Gupta, A. Arockiarajan, editors, February 15–16, 2018 (Chennai), Springer, Singapore, pp. 133–139 (2019)

  8. J. Wang, A. Goel, F. Yang, J.T. Gau, Blank optimization for sheet metal forming using multi-step finite element simulations. Int. J. Adv. Manuf. 40(7–8), 709–720 (2009)

    Article  Google Scholar 

  9. X. Xue, J. Liao, G. Vincze, F. Barlat, Twist springback characteristics of dual-phase steel sheet after non-axisymmetric deep drawing. Int. J. Mater. Form. 10(2), 267–278 (2017)

    Article  Google Scholar 

  10. M. Fazlollahi, M.R. Morovvati, B.M. Dariani, Theoretical, numerical and experimental investigation of hydro-mechanical deep drawing of steel/polymer/steel sandwich sheets. Proc. Inst. Mech. Eng. B J. Eng. Manuf. 233(5), 1529–1546 (2019)

    Article  Google Scholar 

  11. T. Pepelnjak, E. Kayhan, B. Kaftanoglu, Analysis of non-isothermal warm deep drawing of dual-phase DP600 steel. Int. J. Mater. Form. 12(2), 223–240 (2019)

    Article  Google Scholar 

  12. K. Krachenfels, B. Rothammer, R. Zhao, S. Tremmel, M. Merklein, Influence of varying sheet material properties on dry deep drawing process, June (3–7), 2019, in IOP Conference Series: Materials Science and Engineering, p. 012012 (2019)

  13. V. Oleksik, R. Breaz, G. Racz, P.D. Brindasu, O. Bologa, Advanced techniques used in numerical simulation for deep-drawing process, in MATEC Web of Conferences 2019 9th International Conference on Manufacturing Science and Education, Sibiu, Romania (2019)

  14. V. Prakash, D.R. Kumar, A. Horn, H. Hagenah, M. Merklein, Modeling material behavior of AA5083 aluminum alloy sheet using biaxial tensile tests and its application in numerical simulation of deep drawing. Int. J. Adv. Manuf. 106(3–4), 1133–1148 (2020)

    Article  Google Scholar 

  15. S.K. Panthi, S. Saxena, Prediction of crack location in deep drawing processes using finite element simulation. Comput. Mater. Contin. 32(1), 15–27 (2012)

    Google Scholar 

  16. M. Colgan, J. Monaghan, Deep drawing process: analysis and experiment. J. Mater. Process. Technol. 132(1–3), 35–41 (2003)

    Article  CAS  Google Scholar 

  17. Y.K. Sahu, M.K. Pradhan, in Modelling and Simulation of Deep Drawing Process of Circular Cup on AL1200 Using Finite Element Analysis, Advances in Simulation, Product Design and Development: Lecture Notes on Multidisciplinary Industrial Engineering Book Series, M.S. Shunmugam, M. Kanthababu, editors, December 13–15, 2018 (Chennai), Springer, Singapore, pp. 29–42 (2019)

  18. L. Ju, T. Mao, S. Patil, T. Altan, Investigation of forming speed and friction on drawability of Al 5182-O using a servo press with CNC cushion, Center for Precision Forming, The Ohio State University, Columbus, USA, Promotional Literature, Undated

  19. S. Akinlabi, E. Akinlabi, Effect of punch stroke on deformation during sheet forming through finite element, July (3–4), 2017, in IOP Conference Series: Materials Science and Engineering, p. 012004 (2017)

Download references

Author information

Authors and Affiliations

  1. Department of Mechanical Engineering, Lakshmi Narain College of Technology, Bhopal, India

    Yogesh Dewang & Yash Batham

  2. Department of Mechanical Engineering, Sagar Institute of Research Technology and Science, Bhopal, India

    Vipin Sharma

Authors
  1. Yogesh Dewang
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Vipin Sharma
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Yash Batham
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Yogesh Dewang.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Dewang, Y., Sharma, V. & Batham, Y. Influence of Punch Velocity on Deformation Behavior in Deep Drawing of Aluminum Alloy. J Fail. Anal. and Preven. 21, 472–487 (2021). https://doi.org/10.1007/s11668-020-01084-5

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11668-020-01084-5

Keywords

Search

Navigation