Skip to main content
SpringerLink
Log in

Root Cause Analysis of Low Impact Toughness of Cast Steel Yokes Used in Railway Freight Cars

  • Technical Article---Peer-Reviewed
  • Published:
Journal of Failure Analysis and Prevention Aims and scope Submit manuscript

Abstract

The yoke is a safety-critical component of the coupler assembly of railway freight cars and is responsible for absorption of impact loads during service. The present study investigates the root cause of low impact toughness of a particular batch of yoke castings produced in Texmaco Steel Foundry. Examination of microstructure and fracture surface of specimens extracted from the castings reveals the presence of a substantial number of macro- and microporosities. The fracture morphology confirms that the presence of such large number of porosities increases stress concentration and lowers the load-bearing area, resulting in brittle failure and low impact toughness. EDX analysis indicates that these porosities were caused by entrapment of gases during solidification. Subsequent examination indicates that the porosities were caused due to gases generated by combustion of resins/binders used in the sand system or improper venting during the pouring operation.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10

Similar content being viewed by others

References

  1. Wabtec Corporation, Freight Car Draft Arrangements, Online Article (2003). https://www.wabtec.com/documents/6006/freight-car-draft-arrangements

  2. S.M. Noughabi et al., Failure analysis of automatic coupler SA-3 in railway carriages. Eng. Fail. Anal. 14, 903–912 (2007)

    Article  Google Scholar 

  3. A. Shekhter et al., Effect of temper embrittlement and specimen size on Charpy impact testing of a Cr–Mo–V rotor steel. Mater. Sci. Technol. 17, 141–147 (2001)

    Article  Google Scholar 

  4. S.G. Chowdhury et al., Failure analysis of high temperature studs. Eng. Fail. Anal. 8, 521–528 (2001)

    Article  Google Scholar 

  5. P. Lejcek, Grain Boundary Segregation in Metals (Springer, Berlin, 2010)

    Book  Google Scholar 

  6. C.L. Briant, S.K. Banerjee, Embrittlement of Engineering Alloys (Academic Press, London, 1983)

    Google Scholar 

  7. ASM Metals Handbook: vol. 11 - Failure Analysis and Prevention (ASM International, Material Park, 2001)

  8. ASM Metals Handbook: vol. 15 - Casting (ASM International, Material Park, 2001)

  9. L.C.F. Canale et al., Failure Analysis of Heat Treated Steel Components (ASM International, Material Park, 2008)

    Google Scholar 

  10. R.A. Hardin, C. Beckermann, Effect of porosity on deformation, damage, and fracture of cast steel. Metall. Mater. Trans. A 44, 5316–5332 (2013)

    Article  Google Scholar 

  11. N. Tiedje et al., Emission of organic compounds from mould and core binders used for casting iron, aluminium and bronze in sand moulds. J. Environ. Sci. Health., Part A 45, 1866–1876 (2014)

    Article  Google Scholar 

  12. L. Winardi, C.E. Bates, Gas from Green Sand Molds and Organically Bonded Cores, Online Article. http://www.foundry-planet.com/fileadmin/redakteur/pdf-dateien/technical-reports/Gas_from_Green_Sand_Molds_and_Organically_Bonded_Cores_Final.pdf

  13. A. Chojecki et al., Gas evolution from heated bentonite bonded moulding sand. Int. J. Cast Metals Res. 26, 58–63 (2013)

    Article  Google Scholar 

  14. R.L. Naro, Porosity defect in iron castings from mold metal interface reactions. AFS Trans. 99, 839–851 (1999)

    Google Scholar 

  15. R. Monroe, Porosity in castings. AFS Trans. 113, 519–546 (2005)

    Google Scholar 

Download references

Acknowledgments

The authors would like to thank Mr. Manish Boral of IIEST, Shibpur, for his help with SEM imaging and EDX.

Author information

Authors and Affiliations

  1. Steel Foundry Division, Texmaco Rail and Engineering Ltd., Kolkata, 56, India

    R. Sarkar, S. Pathak & D. H. Kela

Authors
  1. R. Sarkar
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. S. Pathak
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. D. H. Kela
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to R. Sarkar.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Sarkar, R., Pathak, S. & Kela, D.H. Root Cause Analysis of Low Impact Toughness of Cast Steel Yokes Used in Railway Freight Cars. J Fail. Anal. and Preven. 19, 76–84 (2019). https://doi.org/10.1007/s11668-018-0565-7

Download citation

  • Received:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11668-018-0565-7

Keywords

Search

Navigation