Abstract
Measurement of residual stress in plasma-sprayed coating is of key importance to optimize their microstructure and mechanical properties. In this study, the x-ray diffraction analysis was carried out using the sin2ψ method to evaluate the residual stress distribution of hydroxyapatite (HAp) coatings produced on titanium substrate by atmospheric plasma spraying (APS) and vacuum plasma spraying (VPS). The sin2ψ method measured strains at different tilt ψ and rotating φ angles around the specimen surface normal. A non-uniform and inhomogeneous stress distribution was present in the both coatings. The measured strain εψφ is plotted versus sin2ψ, showing a nonlinear (elliptical) behavior, which indicates the presence of inhomogeneous triaxial stress distributions within coating, due to the crystalline anisotropy, inhomogeneous cooling rate or solidification of the molten particles. The normal stress values within both HAp coatings produced were found to be tensile in nature, but the values of tensile stresses are significantly higher in APS coating than those values obtained for VPS coating.
Similar content being viewed by others
References
S.V. Dorozhkin and M. Epple, Biological and Medical Significance of Calcium Phosphates, Angew. Chem. Int. Ed., 2002, 41(17), p 3130-3146
L.T. de Jonge, S.C. Leeuwenburgh, J.G. Wolke, and J.A. Jansen, Organic–Inorganic Surface Modifications for Titanium Implant Surfaces, Pharm. Res., 2008, 25(10), p 2357-2369
H. Daugaard, B. Elmengaard, J.E. Bechtold, T. Jensen, and K. Soballe, The Effect on Bone Growth Enhancement of Implant Coatings with Hydroxyapatite and Collagen Deposited Electrochemically and by Plasma Spray, J. Biomed. Mater. Res. Part A, 2010, 92(3), p 913-921
W.S.W. Harun, R.I.M. Asri, J. Alias, F.H. Zulkifli, K. Kadirgama, S.A.C. Ghani, and J.H.M. Shariffuddin, A Comprehensive Review of Hydroxyapatite-Based Coatings Adhesion on Metallic Biomaterials, Ceram. Int., 2017, 44(2), p 1250-1268
J. R. Davis, Ed., Introduction to Thermal Spray Processing, Handbook of Thermal Spray Technology, p 3–13
T.W. Clyne and S.C. Gill, Residual Stresses in Thermal Spray Coatings and Their Effect on Interfacial Adhesion: A Review of Recent Work, J. Therm. Spray Technol., 1996, 5(4), p 401
Y.C. Yang and E. Chang, Influence of Residual Stress on Bonding Strength and Fracture of Plasma-Sprayed Hydroxyapatite Coatings on Ti–6Al–4V Substrate, Biomaterials, 2001, 22(13), p 1827-1836
Z. Gan, H.W. Ng, and A. Devasenapathi, Deposition-Induced Residual Stresses in Plasma-Sprayed Coatings, Surf. Coat. Technol., 2004, 187(2–3), p 307-319
A.G.E.A. Rabiei and A.G. Evans, Failure Mechanisms Associated with the Thermally Grown Oxide in Plasma-Sprayed Thermal Barrier Coatings, Acta Mater., 2000, 48(15), p 3963-3976
Y. Otsuka, H. Kawaguchi, and Y. Mutoh, Cyclic Delamination Behavior of Plasma-Sprayed Hydroxyapatite Coating on Ti–6Al–4V Substrates in Simulated Body Fluid, Mater. Sci. Eng. C, 2016, 67, p 533-541
P. Millet, E. Girardin, C. Braham, and A. Lodini, Stress Influence on Interface in Plasma-Sprayed Hydroxyapatite Coatings on Titanium Alloy, J. Biomed. Mater. Res., 2002, 60(4), p 679-684
Y.C. Yang and E. Chang, Measurements of Residual Stresses in Plasma-Sprayed Hydroxyapatite Coatings on Titanium Alloy, Surf. Coat. Technol., 2005, 190(1), p 122-131
A. Dey and A.K. Mukhopadhyay, Evaluation of Residual Stress in Microplasma Sprayed Hydroxyapatite Coating by Nanoindentation, Ceram. Int., 2014, 40(1), p 1263-1272
Y.C. Yang, E. Chang, B.H. Hwang, and S.Y. Lee, Biaxial Residual Stress States of Plasma-Sprayed Hydroxyapatite Coatings on Titanium Alloy Substrate, Biomaterials, 2000, 21(13), p 1327-1337
R.B. Heimann, Tracking the Thermal Decomposition of Plasma-Sprayed Hydroxylapatite, Am. Miner., 2015, 100(11–12), p 2419-2425
M.E. Fitzpatrick, A.T. Fry, P. Holdway, F.A. Kandil, J. Shackleton, and L. Suominen, Determination of Residual Stresses by X-ray Diffraction, Issue 2, Measurement Good Practice Guide No. 52, National Physical Lab, 2005, p 5–44
W.C. Oliver and G.M. Pharr, An Improved Technique for Determining Hardness and Elastic Modulus Using Load and Displacement Sensing Indentation Experiments, J. Mater. Res., 1992, 7(6), p 1564-1583
Y.C. Tsui, C. Doyle, and T.W. Clyne, Plasma Sprayed Hydroxyapatite Coatings on Titanium Substrates Part 1: Mechanical Properties and Residual Stress Levels, Biomaterials, 1998, 19(22), p 2015-2029
A. Dey and A.K. Mukhopadhyay, Suppl 1-M5: Nanoindentation Study of Phase-pure Highly Crystalline Hydroxyapatite Coatings Deposited by Microplasma Spraying, Open Biomed. Eng. J., 2015, 9, p 65
Y.C. Yang and C.Y. Yang, Mechanical and Histological Evaluation of a Plasma Sprayed Hydroxyapatite Coating on a Titanium Bond Coat, Ceram. Int., 2013, 39(6), p 6509-6516
J.R. Davis, Ed., Handbook of Thermal Spray Technology, ASM International, Russell Township, 2004
S. Saber-Samandari and K.A. Gross, Nanoindentation Reveals Mechanical Properties Within Thermally Sprayed Hydroxyapatite Coatings, Surf. Coat. Technol., 2009, 203(12), p 1660-1664
H. Li, K.A. Khor, and P. Cheang, Properties of Heat-Treated Calcium Phosphate Coatings Deposited by High-Velocity Oxy-Fuel (HVOF) Spray, Biomaterials, 2002, 23(10), p 2105-2112
A. Dey, A.K. Mukhopadhyay, S. Gangadharan, M.K. Sinha, D. Basu, and N.R. Bandyopadhyay, Nanoindentation Study of Microplasma Sprayed Hydroxyapatite Coating, Ceram. Int., 2009, 35(6), p 2295-2304
H. Rao, W.A. Thompson, J.L. Katz, and R.A. Harper, Elastic Constants of the Composite System Hydroxyapatite-Dicalcium Phosphatedihydrate, J. Dent. Res., 1976, 55, p 708
H.J.A. Van Dijk, N. Hattu, and K. Prijs, Preparation, Microstructure and Mechanical Properties of Dense Polycrystalline Hydroxy Apatite, J. Mater. Sci., 1981, 16(6), p 1592-1598
A. Dey and A.K. Mukhopadhyay, Nanoindentation of Brittle Solids, CRC Press, Cambridge, 2014, p 350-353
P.S. Prevéy, The Use of Pearson VII, Distribution Functions in X-Ray Diffraction Residual Stress Measurement, Adv. X-Ray Anal., 1986, 29, p 103-111
V. Sergo, O. Sbaizero, and D.R. Clarke, Mechanical and Chemical Consequences of the Residual Stresses in Plasma Sprayed Hydroxyapatite Coatings, Biomaterials, 1997, 18(6), p 477-482
H. Singh, B.S. Sidhu, D. Puri, and S. Prakash, Use of Plasma Spray Technology for Deposition of High Temperature Oxidation/Corrosion Resistant Coatings–A Review, Mater. Corros., 2007, 58(2), p 92-102
H.W.W. Wong, Heat Transfer Analysis of the Plasma Spray Deposition Process, Ph.D. Thesis, University of British Columbia, 1997
B.R. Gligorijević, M. Vilotijević, M. Šćepanović, N.S. Vuković, and N.A. Radović, Substrate Preheating and Structural Properties of Power Plasma Sprayed Hydroxyapatite Coatings, Ceram. Int., 2016, 42(1), p 411-420
Acknowledgments
The presented investigations were undertaken with support of the “Ministerium für Wissenschaft Forschung und Kunst” in Baden-Württemberg which has financed this project as Kooperatives Promotionskolleg Generierung Mechanismen von Mikrostrukturen (GenMik). The authors would like to gratefully acknowledge DLR (Institute of Technical Thermodynamics, Aerospace Center, Stuttgart, Germany) for the supply of coated samples.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Bosh, N., Mozaffari-Jovein, H. & Müller, C. Determination of Triaxial Residual Stress in Plasma-Sprayed Hydroxyapatite (HAp) Deposited on Titanium Substrate by X-ray Diffraction. J Therm Spray Tech 27, 1238–1250 (2018). https://doi.org/10.1007/s11666-018-0753-8
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11666-018-0753-8