Skip to main content
SpringerLink
Log in

Characteristics of a Plasma Torch Designed for Very Low Pressure Plasma Spraying

  • Technical Note
  • Published:
Journal of Thermal Spray Technology Aims and scope Submit manuscript

Abstract

Unlike atmosphere plasma spraying (APS), very low pressure plasma spraying (VLPPS) can only weakly heat the feed materials at the plasma-free region exit of the nozzle. Most current VLPPS methods have adopted a high power plasma gun, which operates at high arc currents up to 2500 A to remedy the lower heating ability, causing a series of problems for both the plasma torch and the associated facility. According to the Kundsen number and pressures distribution inside of the nozzle in a low-pressure environment, a plasma torch was designed with a separated anode and nozzle, and with the powder feed to the plasma jets inside the nozzle intake. In this study, the pressures in the plasma gas intake, in the nozzle intake and outside the plasma torch were measured using an enthalpy probe. For practice, SUS 316 stainless steel coatings were prepared at the plasma currents of 500-600 A, an arc voltage of 50 V and a chamber pressure of 1000 Pa; the results indicated that coatings with an equiaxed microstructure could be deposited in proper conditions.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7

References

  1. D.-M. Yang, B.-H. Tian, and Y. Gao, Microstructure and Mechanical Properties of the Equiaxed 316L Coating Deposited by Low-Pressure Plasma Spraying, Mater. Sci. Technol. (China), 2011, 19, p 24-27

    CAS  Google Scholar 

  2. Y. Gao, Developments of very Low-Pressure Plasma Spraying and Deposition, Therm. Spray Technol. (China), 2010, 2, p 13-17

    Google Scholar 

  3. Z. Salhi, D. Klein, P. Gougeon, and C. Coddet, Development of Coating by Thermal Plasma Spraying Under Very Low-Pressure Condition 1 Mbar, Vacuum, 2005, 77, p 145-150

    Article  CAS  Google Scholar 

  4. K.H. Baik, P.S. Grant, and B. Cantor, The Equiaxed-Banded Microstructural Transition During Low Pressure Plasma Spraying, Acta Mater., 2004, 52, p 199-208

    Article  CAS  Google Scholar 

  5. K. von Niessen and M. Gindrat, Plasma Spray-PVD: A New Thermal Spray Process to Deposit Out of the Vapor Phase, J. Therm. Spray Technol., 2011, 20(4), p 736-743

    Article  Google Scholar 

  6. A. Refke, M. Gindra, and K. Von Niessen, A Hybrid Coating Technology Between Thermal Spray and PVD for Functional Thin Coating and Large Area Applications, Proceedings of the 2007 International Thermal Spray Conference, Beijing, China, B.R. Marple, M.M. Hyland, Y.-C. Lau, C.-J. Li, R.S. Lima, and G. Montavon, Ed., ASM International, Materials Park, 2007, p 705-710

    Google Scholar 

  7. E. Muehlberger, P. Meyer, LPPS—Thin Film Processes: Overview of Origin and Future Possibilities, Proceedings of the International Thermal Spray Conference 2009, Las Vegas, Nevada, USA, p 737–740

  8. L.T. An and Y. Gao, Effect of Powder Injection Location on Ceramic Coatings Properties When Using Plasma Spray, J. Therm. Spray Technol., 2007, 16, p 967-973

    Article  Google Scholar 

  9. R. Bolot, D. Sokolov, D. Klein, and C. Coddet, Nozzle Developments for Thermal Spray at Very Low Pressure, J. Therm. Spray Technol., 2006, 15(4), p 827-833

    Article  Google Scholar 

  10. X. Chen, Particle Heating in a Thermal Plasma, Pure Appl. Chem., 1988, 60, p 651-662

    Article  Google Scholar 

  11. E. Pfender, Heat and Momentum Transfer to Particles in Thermal Plasma Flows, Pure Appl. Chem., 1985, 57, p 1179-1195

    Article  CAS  Google Scholar 

  12. Y. Gao, A Plasma Torch using for the Low Pressure Plasma Spray, Chinese Patent, in Process, 2010

Download references

Acknowledgment

This work was supported by the National Natural Science Foundation of China general project grant (No. 51172033). The authors are thankful for their support.

Author information

Authors and Affiliations

  1. Thermal Spraying Center of Dalian Maritime University, Dalian, China

    Yang Gao, De Ming Yang & Jianyi Gao

Authors
  1. Yang Gao
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. De Ming Yang
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Jianyi Gao
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Yang Gao.

Additional information

This article is an invited paper selected from presentations at the 2011 International Thermal Spray Conference and has been expanded from the original presentation. It is simultaneously published in Thermal Spray 2011: Proceedings of the International Thermal Spray Conference, Hamburg, Germany, September 27-29, 2011, Basil R. Marple, Arvind Agarwal, Margaret M. Hyland, Yuk-Chiu Lau, Chang-Jiu Li, Rogerio S. Lima, and André McDonald, Ed., ASM International, Materials Park, OH, 2011.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Gao, Y., Yang, D.M. & Gao, J. Characteristics of a Plasma Torch Designed for Very Low Pressure Plasma Spraying. J Therm Spray Tech 21, 740–744 (2012). https://doi.org/10.1007/s11666-011-9730-1

Download citation

  • Received:

  • Revised:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11666-011-9730-1

Keywords

Search

Navigation