Abstract
Many substrates do not sustain the conventional glazing process (i.e., vitreous glazing) due to the relatively high temperature required by this treatment (i.e., up to 1400 °C in some cases) to fuse glazes after their application on the surface to be covered. Flame spraying could appear as a solution to circumvent this limitation and to avoid thermal decomposition of substrates. This contribution describes some structural attributes of glaze coatings manufactured by flame spraying. It also discusses the influence of the feedstock powder morphology and some of its physical properties on coating characteristics.
Similar content being viewed by others
References
G. Aliprandi, Materiaux réfractaires et céramiques techniques – ingénierie des céramiques (Refractory Materials and Technical Ceramics – Ceramics Engineering), Septima Edition, Paris, France, 1979, p 211-236, in French
T. Haure, “Couches multi-fonctionnelles élaborées par plusieurs techniques” (Multifunctional Layers by Multitechnique Process), Ph.D. Thesis, Faculty of Sciences, University of Limoges, France, 2003, in French
J.C. Labbe, E.N. Labrador, P. Lefort, and V. Leroux, Etude de la mouillabilité de l’INVAR par un émail (Study of the INVAR Wettability by an Enamel), Ann. Chim. Sci. Mater., 2000, 25, p 495-507, in French
E. Lugsheider, P. Remer, A. Nyland, and R. Sicking, Thermal Spraying of Bioactive Glass Ceramics, Thermal Spray Science & Technology, C.C. Berndt and S. Sampath, Ed., ASM International, Materials Park, OH, 1995, p 583-587, in French
J. Disam, K. Lübbers, U. Neudert, A. Sickinger (1993) Effect of Spraying Parameters of the LPPS Method on the Structure of Ceramics Coatings. In: C.C. Berndt, T.F. Bernecki (Eds) Thermal Spray: Research, Design and Applications. ASM International, Materials Park, OH, pp 487–491
T. Zhang, Z. Qiu, Y. Bao, D.T. Gawne, K. Zhang (2000) Temperature Profiles and Thermal Stress Analysis of Plasma Sprayed Glass-Composite Coatings. In: C.C. Berndt (Ed) Thermal Spray: Surface Engineering via Applied Research. ASM International, Materials Park, OH, pp 355–361
P. Chraska, V. Brozek, B.J. Kolman, J. Ilavsky, K. Neufuss, J. Dubsky, K. Volenik (1998) Porosity Control of Thermally Sprayed Ceramics Deposits. In: C. Coddet (Ed) Thermal Spray: Meeting the Challenges of the 21st Century. ASM International, Materials Park, OH, p 1299–1304
Y. Bao, T. Zhang, D.T. Gawne (1998) Analysis of Residual Stresses Generated During Plasma Spraying of Glass Coatings. In: C. Coddet (Ed) Thermal Spray: Meeting the Challenges of the 21st Century. ASM International, Materials Park, OH, pp 575–580
T. Poirier, “Dépôts de zircone colloïdale sur des substrats métalliques par projection à la flame d’aérosol” (Colloidal Zirconia Coating on Metallic Substrates by Acrosol Flame Spraying), Ph.D. Thesis, Faculty of Sciences, University of Limoges, France, 2000, in French
A. Proner, “Revêtements par projection thermique” (Coatings by Thermal Spraying), Techniques de l’Ingénieur, M1645, p 11-12, in French
A. Saakov, Yu. Borisov, K. Yushchenko, and G. Komsky, Protective-Decorative Plasma Coatings on Concrete Structures, Thermische Spritzkonferenz, Ed. DVS, German Welding Society, Düsseldorf, Germany, 1993, p 212-215
P.-G. de Gennes, Gouttes, bulles, perles et ondes (Drops, Bubbles, Pearls and Waves), Belin edition, Paris, France, 2002, p 252, in French
Acknowledgments
This study was supported by the Association pour le Développement et la Promotion du Pôle Européen de la Céramique, Limoges, France, under Grant Number 05 005435/01/02. Its support is gratefully acknowledged by the authors.
Author information
Authors and Affiliations
Corresponding author
Additional information
This article is an invited paper selected from presentations at the 2007 International Thermal Spray Conference and has been expanded from the original presentation. It is simultaneously published in Global Coating Solutions, Proceedings of the 2007 International Thermal Spray Conference, Beijing, China, May 14-16, 2007, Basil R. Marple, Margaret M. Hyland, Yuk-Chiu Lau, Chang-Jiu Li, Rogerio S. Lima, and Ghislain Montavon, Ed., ASM International, Materials Park, OH, 2007.
Rights and permissions
About this article
Cite this article
Arcondéguy, A., Grimaud, A., Denoirjean, A. et al. Flame-Sprayed Glaze Coatings: Effects of Operating Parameters and Feedstock Characteristics Onto Coating Structures. J Therm Spray Tech 16, 978–990 (2007). https://doi.org/10.1007/s11666-007-9130-8
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11666-007-9130-8