Abstract
Tailor-welded blanks (TWBs) have numerous advantages over traditional blanks used in manufacturing, such as energy conservation and environment protection. Low formability and weld line movement during forming operation are main limitations of these blanks. In this research, the effects of forming parameters including thickness ratio (TR), rolling direction with respect to the weld line and direction of major stress with respect to the weld line, on formability and weld line movement of TWBs made of galvanized Interstitial-Free (IF) steel were investigated experimentally. Also the effect of application of non-uniform blankholder force on weld line movement was studied by FEM simulation. By utilization of ABAQUS software, blankholders with different geometries, namely one-piece and two-pieces were modeled and forming process was simulated. The results revealed that formability maximized when the major stress and rolling direction were along the weld line. The results showed applying different blankholder forces, by application of the two-pieces blankholder, leads to more uniform strain distribution and correspondingly less weld line movement in TWBs with TR greater than 1. It was also concluded that the effect of geometric discontinuities on reducing formability was greater than the effect of the weld region.
Similar content being viewed by others
References
Y. Shi, P. Zhu, L. Shen, and Z. Lin, Lightweight Design of Automotive Front Side Rails with TWB Concept, Thin Wall. Struct., 2007, 45, p 8–14
Z.Q. Sheng, Formability of Tailor-Welded Strips and Progressive Forming Test, J. Mater. Process. Technol., 2008, 205, p 81–88
S.K. Panda, D.R. Kumar, H. Kumar, and A.K. Nath, Characterization of Tensile Properties of Tailor Welded IF Steel Sheets and Their Formability in Stretch Forming, J. Mater. Process. Technol., 2007, 183, p 321–332
S. Gaied, J.M. Roelandt, F. Pinard, F. Schmit, and M. Balabane, Experimental and Numerical Assessment of Tailor-Welded Blanks Formability, J. Mater. Process. Technol., 2009, 209, p 387–395
S.K. Panda and D.R. Kumar, Improvement in Formability of Tailor Welded Blanks by Application of Counter Pressure in Biaxial Stretch Forming, J. Mater. Process. Technol., 2008, 204, p 70–79
A. Nagasaka, K.I. Sugimoto, M. Kobayashi, K. Makii, and S. Ikeda, Press Formability YAG Laser Welded TRIP/DP Tailored Blanks, J. Phys. IV France, 2004, 115, p 251–258
L.C. Chan, S.M. Chan, C.H. Cheng, and T.C. Lee, Formability and Weld Zone Analysis of Tailor-Welded Blanks for Various Thickness Ratios, J. Eng. Mater. Technol., 2005, 127(2), p 179–185
M.P. Miles, B.J. Decker, and T.W. Nelson, Formability and Strength of Friction-Stir-Welded Aluminum Sheets, Met. Mater. Trans. A, 2004, 35, p 3461–3468
B. Kinsey, N. Krishnan, and J. Cao, A Methodology to Reduce and Quantify Wrinkling in Tailor Welded Blank Forming, Int. J. Mater. Prod. Technol., 2004, 21, p 154–168
Y.M. Heo, S.H. Wang, H.Y. Kim, and D.G. Seo, The Effect of the Drawbead Dimensions on the Weld-Line Movements in the Deep Drawing of Tailor-Welded Blanks, J. Mater. Process. Technol., 2001, 113, p 686–696
S. He, X. Wu, and S.J. Hu, Formability Enhancement for Tailor-Welded Blanks Using Blank Holding Force Control, J. Manuf. Sci. Eng., 2003, 125(3), p 461–467
R. Padmanabhan, M.C. Oliveira, and L.F. Menezes, Deep Drawing of Aluminum-Steel Tailor Welded Blanks, Mater. Des., 2008, 29, p 154–160
M. Ketabchi, M. Abbasi, A. Shamili, M.A. Shafaat, and M.H. Hasannia, Determining Optimum Values of Laser Welding Parameters for a TWB—Using Taguchi Method, International Congress on Welding and Joining (IIWC2009), Tehran, Nov. 30-Dec 3, 2009, p 1–9
C.H. Cheng, M. Jie, L.C. Chan, and C.L. Chow, True Stress-Strain Analysis on Weldment of Heterogeneous Tailor-Welded Blanks—a Novel Approach for Forming Simulation, Int. J. Mech. Sci., 2007, 49, p 217–229
D. Banabic, H.J. Bunge, K. Pöhlandt, and A.E. Tekkaya, Formability of Metallic Materials, Chap. 5, Springer-Verlag, Berlin, 2000
M. Naderi, M. Ketabchi, M. Abbasi, and W. Bleck, Analysis of Microstructure and Mechanical Properties of Different Hot Stamped B-Bearing Steels, Steel Res. Int., 2010, 81, p 216–223
V. Uthaisansuk, U. Prahl, S. Münstermann, and W. Bleck, Experimental and Numerical Failure Criterion for Formability Prediction in Sheet Metal Forming, Comput. Mater. Sci., 2008, 43, p 43–50
W.F. Hosford and R.M. Caddell, Metal Forming-Mechanics and Metallurgy, 3rd ed., Cambridge University Press, Cambridge, 2007, p 247–252
M.C. Stasik and R.H. Wogoner, Forming of Tailor-Welded Aluminum Blanks, Aluminum and Magnesium for Automotive Applications, The Minerals, Metals & Materials Society, Warrendale, PA, 1996, p 69–83
A.A. Zadpoor, J. Sinke, and R. Benedictus, Mechanics of Tailor Welded Blanks: An Overview, Key Eng. Mater., 2007, 344, p 373–382
Acknowledgment
The authors would like to acknowledge Supply Automotive Parts Company (SAPCO), regarding to provision of the materials.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Abbasi, M., Ketabchi, M., Shakeri, H.R. et al. Formability Enhancement of Galvanized IF-Steel TWB by Modification of Forming Parameters. J. of Materi Eng and Perform 21, 564–571 (2012). https://doi.org/10.1007/s11665-011-9946-8
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11665-011-9946-8