Abstract
This work reports a comprehensive examination of the microstructural evolution in Ti6Al4V subjected to high-strain-rate deformation. The sequence of microstructural rearrangements leading to adiabatic shear banding is presented. A detailed microstructural comparison between two types of specimens, one that failed by adiabatic shear and the other that was strained to half its failure strain, is carried out. The main observation is that for this material, the microstructure of the two types of specimens is qualitatively identical, indicating that from approximately half the failure strain until adiabatic shear failure, no additional micromechanism is observed to develop and operate. Overall, the microstructure undergoes a significant refinement with the increasing strain until the formation of dynamically recrystallized grains. It is therefore suggested that the evolution of the volume fraction of recrystallized grains should be characterized from its early onset until final failure by adiabatic shear banding.
Similar content being viewed by others
Notes
PIPS is a trademark of Gatan, Inc., Pleasanton, CA.
References
Y. Bai and B. Dodd: Shear Localization: Occurrence, Theories, and Applications. Pergamon Press, Oxford, United Kingdom, 1992.
H. Tresca: Sur la fluidité et l’écoulement des corps solides, Annales du Conservatoire des Arts et Métiers, 1879, p. 4.
C. Zener and J.H. Hollomon: J. Appl. Phys., 1944, vol. 15 (1), pp. 22–32.
M.A. Meyers: Dynamic Behavior of Materials, J. Wiley & Sons, New York, NY, 1994.
A. Molinari and R.J. Clifton: J. Appl. Mech., 1987, vol. 54 (4), pp. 806–12.
Y. Xu, J. Zhang, Y.L. Bai, and M.A. Meyers: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 811–43.
D. Rittel, Z.G. Wang, and M. Merzer: Phys. Rev. Lett., 2006, vol. 96, p. 075502.
J.A. Hines and K.S. Vecchio: Acta Mater., 1997, vol. 45 (2), pp. 635–49.
M.T. Perez-Prado, J.A. Hines, and K.S. Vecchio: Acta Mater., 2001, vol. 49, pp. 2905–17.
A.H. Chokshi and M.A. Meyers: Scripta Metall. Mater., 1990, vol. 24, pp. 606–10.
M.A. Meyers, V.F. Nesterenko, J.C. LaSalvia, Y.B. Xu, and Q. Xue: J. Phys. IV France Colloq., 2000, vol. C3, part 9, pp. 51–56.
Y. Me-Bar and D. Shechtman: Mater. Sci. Eng., 1983, vol. 58, pp. 181–88.
C. Pizana, E.V. Esquivel, L.E. Murr, C.Y. Pina, M.T. Baquera, I.A. Anchondo, and L.S. Magness: J. Mater. Sci., 2005, vol. 40 (18), pp. 4849–57.
E.A. Trillo, E.V. Esquivel, L.E. Murr, and L.S. Magness: Mater. Charact., 2002, vol. 48 (5), pp. 407–21.
G.A. Li, L. Zhen, C. Lin, R.S. Gao, X. Tan, and C.Y. Xu: Mater. Sci. Eng., 2005, vol. 395 (1–2), pp. 98–101.
D.R. Chichili, K.T. Ramesh, and K.J. Hemker: Acta Mater., 1998, vol. 46 (3), pp. 1025–43.
D. Rittel, P. Landau, and A. Venkert: Phys. Rev. Lett., 2008, vol. 101 (16), p. 165501.
D. Hughes and N. Hansen: Acta Mater., 1997, vol. 45 (9), pp. 3871–86.
Q. Xue and G.T. Gray: Metall. Mater. Trans. A, 2006, vol. 37A (8), pp. 2435–46.
Q. Xue and G.T. Gray: Metall. Mater. Trans. A, 2006, vol. 37A (8), pp. 2447–58.
U. Andrade, M.A. Meyers, K.S. Vecchio, and A.H. Chokshi: Acta Metall. Mater., 1994, vol. 42 (9), pp. 3183–95.
Q. Xue, E.K. Cerreta, and G.T. Gray: Acta Mater. 2007, vol. 55, pp. 691–704.
D. Rittel and Z.G. Wang: Mech. Mater., 2008, vol. 40, pp. 629–35.
S.P. Timothy and I.M. Hutchings: Mater. Sci. Technol., 1985, vol. 1 (7), pp. 526–30.
S.P. Timothy and I.M. Hutchings: Acta Metall. 1985, vol. 33 (4), pp. 667–76.
Q. Xue, M.A. Meyers, and V.F. Nesterenko: Acta Mater., 2002, vol. 50 (3), pp. 575–96.
W.S. Lee and C.F. Lin: J. Mater. Process. Technol., 1998, vol. 75, pp. 127–36.
M.A. Meyers and H.R. Pak: Acta Metall., 1986, vol. 34 (12), pp. 2493–99.
D.R. Chichili, K.T. Ramesh, and K.J. Hemker: J. Mech. Phys. Solids, 2004, vol. 52 (8), pp. 1889–1909.
A. Dorogoy and D. Rittel: Exp. Mech., 2005, vol. 45 (2), pp. 167–77.
A. Dorogoy and D. Rittel: Exp. Mech., 2005, vol. 45 (2), pp. 178–85.
D. Rittel, S. Lee, and G. Ravichandran: Exp. Mech., 2002, vol. 42 (1), pp. 58–64.
H. Kolsky: Proc. Phys. Soc. London, 1949, vol. 62B, pp. 676–700.
T. Leguey, R. Schaublin, P. Marmy, and M. Victoria: J. Nucl. Mater., 2002, vol. 305, pp. 52–59.
S.A. Atroshenko: Mater. Sci. Eng., A, 2004, vol. 378, pp. 293–98.
L.S. Toth, A. Hildenbrand, and A. Molinari: J. de Phys. IV France, 2000, vol. 10, part 9, pp. 365–70.
S. Medyanik, W. Liu, and S. Li.: J. Mech. Phys. Solids, 2007. vol. 55 (7), pp. 1439–61.
S. Mercier, A. Molinari, and Y. Estrin: J. Mater. Sci., 2007, vol. 42, pp. 1455–65.
Author information
Authors and Affiliations
Corresponding author
Additional information
Manuscript submitted June 21, 2009.
Rights and permissions
About this article
Cite this article
Landau, P., Venkert, A. & Rittel, D. Microstructural Aspects of Adiabatic Shear Failure in Annealed Ti6Al4V. Metall Mater Trans A 41, 389–396 (2010). https://doi.org/10.1007/s11661-009-0098-5
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11661-009-0098-5