Abstract
Through-thickness crystallographic texture of a rolled and subsequently annealed Al-Mg continuous cast (CC) alloy was examined. Results showed that the annealed sheet developed a through-thickness texture gradient with the form of a stronger cube texture at the surface when compared to the center layers and varied R orientations through the thickness. While the through-thickness texture gradient was not attributed to the shear related texture, it was still related to the extent of deformation within the sheet.
References
I.L. Dillmore and W.T. Roberts: J. Inst. Met., 1963–64, vol. 92, pp. 193–99.
N. Hansen and H. Mecking: in ICOTOM 4, G.J. Davies, I.L. Dillamore, R.C. Hudd, and J.S. Kallend, eds., The Metals Society, London, 1975, pp. 34–46.
R.E. Bauer, H. Mecking, and K. Lüke: Mater. Sci. Eng., 1977, vol. 27, pp. 163–80.
H.O. Asbeck and H. Mecking: Mater. Sci. Eng., 1978, vol. 34, pp. 111–19.
W. Truszkowski, J. Król, and B. Major: Metall. Trans. A, 1980, vol. 11A, pp. 749–58.
W. Truszkowski, J. Król, and B. Major: Metall. Trans. A, 1982, vol. 13A, pp. 665–69.
H.P. Kneijnsberg, C.A. Verbraak, and M.J. Ten Bouwhuijs: Acta Metall., 1985, vol. 33, pp. 1759–67.
C.S. Lee and B.J. Duggan: Metall. Trans. A, 1991, vol. 22A, pp. 2637–43.
B. Major: Mater. Sci. Technol., 1992, vol. 8, pp. 510–15.
C.-H. Choi, J.W. Kwon, K.H. Oh, and D.N. Lee: Acta Mater., 1997, vol. 45, pp. 5119–28.
W. Mao: Mater. Sci. Eng., 1998, vol. A257, pp. 171–77.
C.-H. Choi and D.N. Lee: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 2217–22.
O.-V. Mishin, B. Bay, and D.J. Jensen: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 1653–62.
M. Höscher, D. Raabe, and K. Lüke: Acta Metall. Mater., 1994, vol. 42, pp. 879–86.
“Metals Test Methods and Analytical Procedures”: in Annual Book of ASTM Standards, ASTM INTERNATIONAL, West Conshohocken, PA, 2003, pp. 427–50.
L.G. Schulz: J. Appl. Phys., 1949, vol. 20, pp. 1033–36.
H.J. Bunge: Texture Analysis in Material Science, 1st ed., Butterworths and Co., London, 1982.
S. Matthies and G.W. Vinel: Phys. Stat. Sol. B, 1961, vol. 112, pp. K111-K114.
J.S. Kallend, U.F. Kocks, A.D. Rollett, and H.-R. Wenk: Mater. Sci. Eng., 1991, vol. A132, pp. 1–11.
M. Somerday and F.J. Humpreys: Mater. Sci. Technol., 2003, vol. 19, pp. 20–29.
J. Liu and J.G. Morris: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 2029–32.
J. Liu and J.G. Morris: Mater. Sci. Eng. A, 2004, vol. 385, pp. 342–51.
J. Liu: Ph.D. Thesis, University of Kentucky, Lexington, KY, 2003.
J. Pospiech and K. Lüke: Acta Metall., 1975, vol. 23, pp. 997–1007.
O. Engler: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 1517–27.
J. Grewen and M.V. Heimendahl: Z. Metallkd., 1968, vol. 59, pp. 205–12.
H. Ahlborn, E. Hornbogen, and U. Köter: J. Mater. Sci., 1969, vol. 4, pp. 944–50.
J. Hirsch and K. Lüke: Acta Metall., 1985, vol. 33, pp. 1927–38.
Author information
Authors and Affiliations
Additional information
Financial support from the United States Department of Energy (under Contract No. DE-FC07-01ID14193) is gratefully acknowledged. The authors are grateful to Dr. S.D. Ridder for assistance in the experimental work.
Identification of equipment or software does not imply recommendation or endorsement by NIST, the Department of Commerce, or the United States Government, nor does it imply that the identified equipment or software is the best available.
Rights and permissions
About this article
Cite this article
Liu, J., Banovic, S.W., Biancaniello, F.S. et al. Through-thickness texture gradient in an annealed Al-Mg alloy sheet. Metall Mater Trans A 36, 869–874 (2005). https://doi.org/10.1007/s11661-005-0200-6
Received:
Issue Date:
DOI: https://doi.org/10.1007/s11661-005-0200-6