Abstract
The mechanical behavior of the joints inside a loess layer is greatly important in weak intercalation studies owing to its involvement in a wide range of landslides in the loess region in China. The shear behavior of the joints in the loess stratum during direct shear and cyclic loadings was investigated using the PFC2D discrete element software. Loess mudstone and mudstone with weak intercalated layer materials were subjected to direct testing, and cyclic shear tests were conducted with consideration to the influence of normal stress and shear velocity. The macroscopic properties and damage patterns were obtained for six numerical configurations; namely, loess-weathered mudstone with 0°, 10°, and −10° joints and weathered mudstone with 0°, 10°, and −10° weak intercalated layers. The numerical test results revealed that, in the direct shear tests, the shear stress and shear displacement of the samples increased with the normal stress. In the cyclic shear tests with a total cycle number N=20, the shear stress-shear strain curve of the six different configurations exhibited a hysteresis loop. The numerical tests also revealed that, under cyclic shear, the normal stress and shear velocity affected the shear strength. The degree of damage increased as the shear velocity decreased from 0.1 mm/s to 0.005 mm/s for all six numerical configurations. Compared with the damage pattern of the direct shear tests, the damage of the cyclic shear tests mainly comprised shear cracks and fractures, some shaking consolidation settlement and fewer shear strain occurred around the joints. In the direct shear tests, more compression cracks and fractures occurred in the samples. The damage mainly developed along the joints, and shearing-off damage occurred. The results obtained by this study further elucidate the failure mechanism and microscopic damage response of the joints in the loess stratum in Northwest China.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Adaehi T, Oka F, Koike, M (2005) An Elasto-viscoplastic Constitutive Model with Strain-softening for Soft Sedimentary Rocks. Soils and Foundations 45(2): 125–133. https://doi.org/10.3208/sandf.45.2_125
Bobet A, Einstein HH (1998) Fracture coalescence in rock-type materials under uniaxial and biaxial compression. International Journal of Rock Mechanics and Mining Sciences 35(7): 863–888. https://doi.org/10.1016/S0148-9062(98)00005-9
Barton N (1973) Review of a new shear strength criterion for rock joints. Engineering Geology 7(4): 287–332. https://doi.org/10.1016/0013-7952(73)90013-6
Bahaaddini M, Sharrock G, Hebblewhite BK (2013) Numerical investigation of the effect of joint geometrical parameters on the mechanical properties of a non-persistent jointed rock mass under uniaxial compression. Computers and Geotechnics 49: 206–225. https://doi.org/10.1016/j.compgeo.2012.10.012
Bewick RP, Kaiser PK, Bawden WF (2014) Shear rupture under constant normal stiffness boundary conditions. Tectonophysics 634: 76–90. https://doi.org/10.1016/j.tecto.2014.07.016
Coli N, Berry P, Boldini D (2011) In situ non-conventional shear tests for the mechanical characterisation of a bimrock. International Journal of Rock Mechanics and Mining Sciences 48: 95–102. https://doi.org/10.1016/j.ijrmms.2010.09.012
Chiu C, Weng M (2019) Simulating interface characteristics by using a particulate interface model of a discrete element method. Computers and Geotechnics 109: 1–11. https://doi.org/10.1016/j.compgeo.2019.01.011
Chiu C, Wang T, Weng M, et al. (2013) Modeling the anisotropic behavior of jointed rock mass using a modified smooth-joint model. International Journal of Rock Mechanics and Mining Sciences 62: 14–22. https://doi.org/10.1016/j.ijrmms.2013.03.011
Cho N, Martin CD, Sego DC (2007) A clumped particle model for rock. International Journal of Rock Mechanics and Mining Sciences 44: 997–1010. https://doi.org/10.1016/j.ijrmms.2007.02.002
Erken A, Ulker BMC (2007) Effect of cyclic loading on monotonic shear strength of fine-grained soils. Engineering Geology 89(3–4): 243–257. https://doi.org/10.1016/j.enggeo.2006.10.008
Huang D, Wang J, Liu S (2015) A comprehensive study on the smooth joint model in DEM simulation of jointed rock masses. Granular Matter 17: 775–791. https://doi.org/10.1007/s10035-015-0594-9
Hunt SP, Meyers AG, Louchnikov V (2003) Modelling the Kaiser effect and deformation rate analysis in sandstone using the discrete element method. Computers and Geotechnics 30(7): 611–621. https://doi.org/10.1016/S0266-352X(03)00061-2
Hsieh YM, Li HH, Huang TH, et al. (2008) Interpretations on how the macroscopic mechanical behavior of sandstone affected by microscopic properties—Revealed by bonded-particle model. Engineering Geology 99(1–2): 1–10. https://doi.org/10.1016/j.enggeo.2008.01.017
Itasca Consulting Group Inc. Manual of particle flow code in 2-dimension (Version 3.10). Minneapolis: Itasca Consulting Group Inc, 2005.
Itasca Consulting Group Inc. Manual of particle flow code in 2-dimension: theory and background. 3.1st ed. Minneapolis: Itasca Consulting Group Inc, 2008: 1–12.
Iwashita K, Oda M (2000) Micro-deformation mechanism of shear banding process based on modified distinct element method. Powder Technology 109(1–3): 192–205. https://doi.org/10.1016/S0032-5910(99)00236-3
Kulatilake PHSW, Malama B, Wang J (2001) Physical and particle flow modeling of jointed rock block behavior under uniaxial loading. International Journal of Rock Mechanics and Mining Sciences 38(5): 641–657. https://doi.org/10.1016/S1365-1609(01)00025-9
Landry H, Lague C, Roberge M (2006) Discrete element representation of manure products. Computers and Electronics in Agriculture 51(1–2): 17–34. https://doi.org/10.1016/j.compag.2005.10.004
Labuz JF, Zhang A (2012) Mohr-Coulomb Failure Criterion. Rock Mechanics & Rock Engineering 45: 975–979. https://doi.org/10.1007/s00603-012-0281-7
Mehranpour MH, Kulatilake PHSW (2017) Improvements for the smooth joint contact model of the particle flow code and its applications. Computers and Geotechnics 87: 163–177. https://doi.org/10.1016/j.compgeo.2017.02.012
Nguyen NHT, Bui HH, Nguyen GD, et al. (2017) A cohesive damage-plasticity model for DEM and its application for numerical investigation of soft rock fracture properties. Int J Plast 98: 175–196. https://doi.org/10.1016/j.ijplas.2017.07.008
Potyondy DO, Cundall PA (2004) A bonded-partical model for rock. International Journal of Rock Mechanics and Mining Sciences 41(8): 1329–1364. https://doi.org/10.1016/j.ijrmms.2004.09.011
Potyondy DO (2015) The bonded-particle model as a tool for rock mechanics research and application: current trends and future directions. Geosystem Engineering 18(1): 1–28. https://doi.org/10.1080/12269328.2014.998346
Prudencio M, Van Sint Jan M (2007) Strength and failure modes of rock mass models with non-persistent joints. International Journal of Rock Mechanics and Mining Sciences 44(6): 890–902. https://doi.org/10.1016/j.ijrmms.2007.01.005
Saadat M, Taheri A (2019) A cohesive discrete element based approach to characterizing the shear behavior of cohesive soil and clay-infilled rock joints. Computers and Geotechnics 114: 103–109. https://doi.org/10.1016/j.compgeo.2019.103109
Stafford PJ, Bommer JJ (2009) Empirical equations for the prediction of the equivalent number of cycles of earthquake ground motion. Soil Dynamics and Earthquake Engineering 29(11–12): 1425–1436. https://doi.org/10.1016/j.soildyn.2009.05.001
Stavrou A, Murphy W (2018) Quantifying the effects of scale and heterogeneity on the confined strength of micro-defected rocks. International Journal of Rock Mechanics and Mining Sciences 102: 131–143. https://doi.org/10.1016/j.ijrmms.2018.01.019
Tatone BSA, Grasselli G (2013) An investigation of discontinuity roughness scale dependency using high-resolution surface measurements. Rock Mechanics and Rock Engineering 46: 657–681. https://doi.org/10.1007/s00603-012-0294-2
Tang CA, Lin P, Wong RHC, et al. (2001) Analysis of crack coalescence in rock-like materials containing three flaws-Part II: numerical approach. International Journal of Rock Mechanics and Mining Sciences 38(7): 925–939. https://doi.org/10.1016/S1365-1609(01)00065-X
Ord A, Hobbs B, Regenauer-Lieb K (2007) Shear band emergence in granular materials — a numerical study. International Journal for Numerical & Analytical Methods in Geomechanics 31(3): 373–393. https://doi.org/10.1002/nag.590
Wang Y, Tonon F (2009) Modeling Lac du Bonnet granite using a discrete element model. International Journal of Rock Mechanics and Mining Sciences 46(7): 1124–1135. https://doi.org/10.1016/j.ijrmms.2009.05.008
Wen BP, He L (2012) Influence of lixiviation by irrigation water on residual shear strength of weathered red mudstone in northwest china: implication for its role in landslides’ reactivation. Engineering Geology 151: 56–63. https://doi.org/10.1016/j.enggeo.2012.08.005
Wong LNY, Zhang XP (2014) Size effects on cracking behavior of flaw-containing specimens under compressive loading. Rock Mechanics and Rock Engineering 47: 1921–1930. https://doi.org/10.1007/s00603-013-0424-5
Wang C, Tannant DD, Lilly PA (2003) Numerical analysis of the stability of heavily jointed rock slopes using PFC2D. International Journal of Rock Mechanics and Mining Sciences 40(3): 415–424. https://doi.org/10.1016/S1365-1609(03)00004-2
Yoon J (2007) Application of experimental design and optimization to PFC model calibration in uniaxial compression simulation. International Journal of Rock Mechanics and Mining Sciences 44(6): 871–889. https://doi.org/10.1016/j.ijrmms.2007.01.004
Yang X, Kulatilake PHSW, Jing H, et al. (2015) Numerical simulation of a jointed rock block mechanical behavior adjacent to an underground excavation and comparison with physical model test results. Tunnelling and Underground Space Technology 50: 129–142. https://doi.org/10.1016/j.tust.2015.07.006
Zhang Z, Wang T, Wu S, et al. (2018) Dynamics characteristic of red clay in a deep-seated landslide, Northwest China: An experiment study. Engineering Geology 239: 254–268. https://doi.org/10.1016/j.enggeo.2018.04.005
Zhang G, Karakus M, Tang H, et al. (2014) A new method estimating the 2D joint roughness coefficient for discontinuity surfaces in rock masses. International Journal of Rock Mechanics and Mining Sciences 72: 191–198. https://doi.org/10.1016/j.ijrmms.2014.09.009
Zhang XP, Wong LNY (2013) Loading rate effects on cracking behavior of flaw-contained specimens under uniaxial compression. International Journal of Fracture 180: 93–110. https://doi.org/10.1007/s10704-012-9803-2
Zhang Z, Sheng Q, Fu X, et al. (2020) An approach to predicting the shear strength of soil-rock mixture based on rock block proportion. Bulletin of Engineering Geology and the Environment 79: 2423–2437. https://doi.org/10.1007/s10064-019-01658-0
Author information
Authors and Affiliations
Corresponding author
Additional information
Acknowledgments
This study was sponsored by National Natural Science Foundation of China (No.41902269), and Chinese Universities Scientific Fund (2020TC095). We thank Liwen Bianji, Edanz Editing China (http://www.liwenbianji.cn/ac), for editing the English text of a draft of this manuscript.
Rights and permissions
About this article
Cite this article
Zhang, Zl., Wang, T. Numerical analysis of loess and weak intercalated layer failure behavior under direct shearing and cyclic loading. J. Mt. Sci. 17, 2796–2815 (2020). https://doi.org/10.1007/s11629-020-6178-0
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11629-020-6178-0