Abstract
This paper presents a simple hypoplastic constitutive model for overconsolidated clays. The model needs five independent parameters and is as simple as the modified Cam Clay model but with better performance. A structure tensor is introduced to account for the history dependence. Simulations of various elementary tests show that the model is capable of capturing the salient behavior of overconsolidated clays.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
The effect of overconsolidation on the mechanical behavior of clays is well documented in the literature. Unlike normally consolidated clays, overconsolidated (OC) clays show peak strength along with dilatancy and postpeak strain softening under shearing. Accurate characterization of the behavior of OC clays is of great importance for many engineering applications, such as foundation design [1], slope stabilization [4], and embankment construction [36].
During the last four decades, great effort has been devoted to the development of constitutive models for predicting the mechanical behaviors of OC clays [2, 10, 17, 19, 25, 28, 52, among others]. Most of these works were based on the critical state concept [31, 32], and developed from the original or modified Cam Clay (MCC) models. The capacity of the models has been largely enhanced by introducing various concepts, such as bounding surface [6] and subloading surface [12]. While these approaches have achieved certain success, some fundamental issues still remain unsolved, particularly the model complexity and the numerous model parameters. Often, the models make use of the evolution of the yield surfaces, and switch functions to differentiate between loading and unloading, which hamper the numerical implementation of the models [34].
Recently, there is growing interest in the use of hypoplasticity to model the mechanical behaviors of soils [3, 7,8,9, 11, 13, 14, 18, 20, 26, 29, 30, 37,38,39,40,41, 43, 48]. Hypoplastic models were developed without recourse to the concept in elastoplasticity theory such as yield surface, plastic potential and decomposition of the strain into elastic and plastic parts. Therefore, hypoplastic models are usually characterized by simple formulations and few parameters. Moreover, hypoplastic model possesses a single formulation for the incrementally nonlinear behavior without using a predefined criterion for loading and unloading. These features make the numerical implementation of hypoplastic models, in comparison to elastoplastic models, easier and more straightforward [35, 40].
The early hypoplastic models [18, 45], containing four tensor polynomial terms with four material parameters, are as simple as the MCC model. The stress tensor is considered as the only state variable in such basic models. As a consequence, these basic models are not able to account for the complex history dependence. Later, the critical state concept was incorporated in hypoplasticity by introducing the void ratio as an additional state variable to account for the effect of density. The first hypoplastic model with critical state by Wu et al. [44] represents an important development of hypoplasticity in this regard. This extension leads to a number of critical state hypoplastic models for sand [3, 11, 15, 39, 46, 47].
The first attempt to extend hypoplastic model to clay was made by Niemunis [26, 27], who combined the critical state concept of clay with hypoplasticity to describe the behavior of OC clays. Based on this model, Mašín [21, 23, 24] proposed several hypoplastic models for OC clays. While these models can capture some features of OC clays, their performance in undrained condition is rather poor. Huang et al. [16] proposed a hypoplastic model for normally consolidated soils, emphasising the undrained behavior. However, this model made use of a loading criterion, which is at the sacrifice of the model simplicity. More recently, Shi et al. [33] introduced a nonlinear Hvorslev surface into the Cam–Clay hypoplastic model [23] for heavily OC clays. This model, however, inherits the shortcomings of the basic model. Moreover, the capacity of the aforementioned models is frequently gained at the cost of their simplicity. Therefore, further extensions based on these models will inevitably increase the complexity of the model and the number of the parameters.
The primacy of this work is to develop a hypoplastic constitutive model that is capable of describing the salient behaviors of OC clay, while still keeping the model simplicity. Our development is based on a basic constitutive model proposed recently by Wu et al. [48]. First, the background of hypoplasticity and the basic idea for overconsolidation are introduced. Next, a simple hypoplastic model is developed and some numerical tests are performed to show the model performance. In the following, except where specified otherwise, effective stress is used.
2 General framework for OC clays
2.1 Constitutive equation
To gain perspective, let us start with the following hypoplastic constitutive framework proposed by Wu and Kolymbas [43].
where \(\mathbf{T}\) is the Cauchy stress tensor; \(\mathbf{D}\) is the strain rate (stretching) tensor. The tensorial functions \({\varvec{\mathcal{L}}}\) and \(\mathbf{N}\) are of the 4th and 2nd order, respectively. The colon : denotes an inner product between two tensors. \(\Vert \mathbf{D} \Vert\) stands for the Euclidean norm of the stretching tensor. The Jaumann stress rate tensor \(\mathring{\mathbf{T}}\) is defined in terms of the material time-derivative of the Cauchy stress tensor \(\dot{\mathbf{T }}\) and the spin tensor \(\mathbf{W}\):
The stretching and spin tensors are related to the velocity gradient tensor through
where \(\varvec{v}\) is the velocity and \(\varvec{\nabla}\) is the gradient operator.
The functions \({\varvec{\mathcal{L}}}\) and \(\mathbf{N}\) must be isotropic to remain invariant under rigid body rotations. Since \({\varvec{\mathcal{L}}}\) is independent of \(\mathbf{D}\), constitutive equations in the form of Eq. (1) are necessarily rate independent. This can be easily ascertained by the fact that Eq. (1) is positively homogeneous of the first degree in strain rate \(\mathbf{D}\). To show this, we can write Eq. (1) in the following form by making use of Euler’s theorem for homogeneous functions.
where \({\vec {\mathbf{D}}}=\mathbf{D} /\Vert \mathbf{D} \Vert\) is the direction of strain rate and \(\otimes\) stands for the dyadic product. The term in the square brackets in Eq. (4) is the directional stiffness tensor, which can be viewed as the counterpart of the tangential stiffness of elastoplastic models. Obviously, the directional stiffness tensor depends on the direction of strain rate \({\vec {\mathbf{D}}}\). Therefore, loading and unloading in the hypoplastic model (4) are implicitly stated without additional loading criterion. This is different from elastoplastic models, where two stiffness tensors, one for loading and the other for unloading, are used. Furthermore, elastoplastic models need explicit loading criterion to decide which stiffness shall be used.
2.2 Basic idea for overconsolidation
We propose to consider the effect of overconsolidation by manipulating the nonlinear term in constitutive Eq. (1). This idea can be best explained by examining the effective stress paths in undrained triaxial test with the help of the so-called response envelope for the case of isochoric deformation.
Staring from a stress state, a stress rate (stress increment) can be obtained for a strain rate from constitutive Eq. (1). In other words, a response is obtained for a strain rate. For a rosette of strain rates with a constant magnitude, we obtain a rosette of stress increments, which can be represented in the stress space graphically (response envelope). Obviously, the distance from the initial stress \(\mathbf{T} _0\) to any point on the response envelope represents the stiffness along certain strain rate. The response envelope at a given initial stress state \(\mathbf{T} _0\) is the surface spanned by all stresses \(\mathbf{T} =\mathbf{T} _0+\Delta \mathbf{T}\). The response envelopes can be best visualized by considering the Rendulic plane for strain rate and stress, e.g., the \(p-q\) plane, where the stress increments can be represented by vectors.
Let us consider an isotropic stress state, with \(T_{11} = T_{22}=T_{33}\). The response envelope of constitutive Eq. (1) consists of the contributions from the linear and nonlinear terms, which is shown in Fig. 1. The response envelope of the linear term, which is incrementally linear, represents an ellipse with the initial stress in the center [43]. The nonlinear term remains independent of the direction of strain rate and represents a translation along the p-axis. As a result of the translation, the initial stress is not at the center of the ellipse as shown in Fig. 1 for the case of Np > 0. Obviously, the initial stress is shifted to the right, which gives rise to smaller stiffness for loading (smaller distance to the right) and larger stiffness for unloading (larger distance to the left).
We proceed to consider the effective stress path during undrained triaxial compression test starting from an isotropic stress state. For an isochoric strain rate, the linear term gives rise a pure deviatoric stress increment, i.e., \(\Delta p =0\). The nonlinear term gives rise to a vector pointed to the origin along the p-axis (see the vector for Np > 0 in Fig. 1). The overall response of constitutive Eq. (1) consists of the contributions of the linear and nonlinear parts. The vector sum of the two parts leads to a stress increment pointed toward left. Therefore, the initial effective stress path starting from an isotropic stress state is directed to the left. This agrees in principle with the experimental observations for normally consolidated soils.
For OC clays, however, the shape of the effective stress paths is known to depend on OCR. The stress path becomes steeper for light overconsolidation and turns toward right for heavy overconsolidation. As shown in Fig. 1, the initial stress path can be manipulated by the nonlinear term. For Np = 0, the stress path is vertical. For Np < 0, the stress path turns toward right. The idea is to introduce a structure tensor into the nonlinear term, which represents the history dependence.
2.3 Constitutive framework
Following the above reasoning, we seek to establish a framework to incorporate the consolidation history by introducing a structure tensor in the following way:
where \(\mathbf{S}\) is a second-order symmetric tensor representing the overconsolidation.
Bearing in mind that the structure tensor shall vanish for normal consolidation \((\hbox{OCR} = 1)\), we proceed to introduce the following simple expression for the structure tensor:
where \(\alpha\) is a model parameter; R is the stress ratio representing the overconsolidation defined as:
in which \(p_e^+\) and \(p_e\) are the pre-consolidation pressure in MCC model and the Hvorslev equivalent pressure, respectively. Their definitions are shown in Fig. 2 with the formulations given as follows:
where the inclination M corresponds to the stress ratio at the critical state by \(M= 6\text{sin}\phi _c/(3-\text{sin}\phi _c)\) with \(\phi _c\) being the critical state friction angle; the index \(\lambda ^*\) is the slope of the normal compression line in the double logarithmic \({\text{ln}}(1+e)-{\text{ln}} p\) plane; N denotes the logarithmic value of the specific volume at the reference stress \(p_r=1\) kPa. Note that the parameter N is different from the tensorial function \(\textbf{N}\) in Eq. (1).
The stress ratio R is widely used for overconsolidation in some elastoplastic models [50, 51]. Note that R has a different physical meaning from the conventional overconsolidation ratio OCR. A smaller value of R corresponds to a larger OCR. Obviously, the structure tensor vanishes for normal consolidation and critical state with \(R = 1\). In these cases, the model (5) degenerates to the basic Eq. (1).
2.4 Improvement for undrained tests
Many undrained tests on sand and normally consolidated clay in the literature show an initially vertical effective stress path starting from an isotropic stress state. This behavior suggests an initially elastic behavior. However, as illustrated in Fig. 1, the hypoplastic model (1) predicts an effective stress path directed toward left from an isotropic stress state. Some attempts have been made to remedy this shortcoming [16, 22, 26, 49]. We proceed to multiply the nonlinear term in model (1) with a function \(f_u\), which vanishes for isochoric strain rate to give
where the multiplier \(f_u\) is defined by
with \(\mathbf{B }=-{{\varvec{\mathcal{L}}}}^{-1}:\mathbf{N}\) denoting the flow rule of the model. The multiplier \(f_u\) can be viewed as the cosine of the angle between the strain rate direction \({\vec {\mathbf{D}}}\) and the flow direction \({\vec {\mathbf{B}}}\).
Figure 3 shows the mechanism of the function \(f_u\) on the improvement of an undrained triaxial test. Compared to typical experimental results, the original prediction (dashed line) bends significantly toward the left at the onset of shearing. This unrealistic prediction, however, can be largely improved by the function \(f_u\). Note that the function \(f_u\) does not influence the shear strength at the critical state since \(f_u=1\) at the critical state. To show this, let us first consider the stress states (a) and (b) at the beginning of shearing and at the critical state, respectively. For an undrained test with isochoric deformation, a purely deviatoric strain direction is expected. Therefore, the flow direction \({\vec {\mathbf{B}}}\) and the strain direction \({\vec {\mathbf{D}}}\) are perpendicular at the onset of the shearing while coincide at the critical state. Obviously, the variations of \({\vec {\mathbf{B}}}\) and \({\vec {\mathbf{D}}}\) give rise to a monotonic increase of \(f_u\) from 0 to 1 (\(0\leqslant f_u \leqslant 1\)) in an undrained shear test starting from an isotropic stress state. This leads to an initially vertical effective stress path from an isotropic stress state. On the other hand, the function \(f_u\) cannot change the isotropic stress state of the proposed model. As shown by the isotropic stress state (c) in Fig. 3, \({\vec {\mathbf{B}}}\) and \({\vec {\mathbf{D}}}\) with the same direction lead to the function \(f_u =1\).
3 Hypoplastic constitutive model for OC clay
Having established the framework to incorporate the consolidation history, we proceed to consider the following specific constitutive model proposed by Wu et al. [48]. This model consists of three linear terms and one nonlinear term.
in which \(C_i\,(i=1,2,3,4)\) are dimensionless material constants. \(\mathbf{T} ^*\) is the deviatoric part of \(\mathbf{T}\). The performance of the above constitutive equation is well documented in the literature [48]. For the numerical implementation of the model we refer to Wang et al. [40].
Combining Eq. (9) with the constitutive model (11), we obtain a simple hypoplastic model as follows for OC clays:
Since the above equation is written in tensorial notation, the essential features of the model can be hardly perceived without detailing it in component form. For details of the component form of hypoplastic models, the reader are referred to [45]. The complete formulations of the constitutive equation are given in the "Appendix".
4 Model performance
We consider several element tests, including oedometer tests and triaxial compression tests, to show the model performance. The material constants listed in Table 1 are used to obtain the numerical results throughout the paper.
Note that the material constants \(C_i\,(i=1,2,3,4)\) can be related to some well-established parameters in soil mechanics, such as the initial tangential modulus \(E_i\), the initial Poisson’s ratio \(\nu _i\), the critical friction angle \(\phi _c\). These parameters can be readily determined with a single triaxial compression test [45]. Moreover, the constitutive equation is homogenous in stress, which means that the parameter \(E_i\) can be scaled by \(\lambda ^*\) for clays. We are then left with five independent parameters for the constitutive Eq. (12). A detailed procedure to calibrate the model parameters can be found in our forthcoming paper.
4.1 Oedometer test
The oedometer test is commonly used to determine the consolidation history of OC clays. The ratio of the radial stress to the vertical stress \(K_0\), called earth pressure coefficient at rest, is important for a variety of engineering problems.
The predicted \(K_0\) using the basic model (11) and the proposed model (12) is shown in Fig. 4a. It shows that \(K_0\) decreases with increasing critical friction angle \(\phi _c\). The predicted \(K_0\) by the proposed model is slightly larger than that obtained from the basic model. The results are compared to Jáky’s empirical relation: \(K_0=1-\text{sin}\phi _c\). Obviously, the model predictions agree well with the empirical relationship by Jáky. Unlike Jáky’s formula, the models show nonlinear relationship particularly for high friction angle.
The predicted \(e-\text{ln} p\) curves from oedometer tests are compared to those obtained from isotropic compression tests. Figure 4b shows that the same loading index \(\lambda ^*\) can be obtained from both tests, while the two tests predict slightly different unloading behaviors. Usually, a larger unloading index can be obtained from the isotropic test. Since the oedometer tests predict similar consolidation behavior as the isotropic compression test, the parameters N and \(\lambda ^*\) can be determined from an oedometer test as well. It is noteworthy that some hypoplastic models [16, 26, 39] predict different normal compression lines in isotropic and in oedometer conditions.
Unlike some existing hypoplastic models for clays [16, 21, 24, 42], the unloading index, i.e., \(\kappa ^*\), is not used in the proposed model. In fact, the unloading index facilitates the predictions of unloading behavior of one loading cycle, while it has little contribution in capturing the cyclic behavior with a large number of loading cycles [24]. Although the unloading index is not included in the model, the unloading behavior can be predicted fairly well. This is different from the MCC model, in which the elastic behaviors are solely controlled by the unloading index. In hypoplastic model, however, we do not differentiate between the elastic and the plastic deformation. Therefore, it is not necessary to include the unloading index.
4.2 Triaxial compression test
We now consider the model performance in triaxial compression tests. Both drained and undrained triaxial compression tests are simulated to show the model capacity for describing the deformation and strength behavior of OC clays. A wide range of overconsolidation ratios from 1 to 10 is considered. The initial OCR is specified by defining different initial void ratios, which are obtained by performing isotropic loading–unloading tests with different pre-consolidation pressures. In all simulations, a constant confining pressure of 100 kPa is used.
The numerical simulation of drained triaxial tests with various OCRs is shown in Fig. 5. The stress–strain curves in Fig. 5a show that the strength behavior changes from strain hardening to strain softening with the increase of the OCRs. At large strain, all stress–strain curves approach asymptomatically to the critical state, characterized by the critical friction angle. Correspondingly, the volumetric responses change from contraction to dilatancy with the increase of the OCRs. With further increasing the deformation, the volumetric strain rate vanished at the critical state, as shown in Fig. 5b. The effective stress path in the \(p-q\) plane can be normalized by the Hvorslev equivalent pressure \(p_e\), defined as a mean stress at the isotropic normal compression line at the current void ratio. As may be seen from Fig. 5c all normalized effective stress paths eventually converge to the critical state regardless of the initial OCRs.
The numerical results of undrained triaxial tests with various OCRs are shown in Fig. 6. The result of the stress ratio (q/p) is shown in Fig. 6a. For tests with high OCRs, along with the deformation, the stress ratios (q/p) first increase to reach a peak and then decrease to approach the critical state. As shown in Fig. 6b that the initial OCR significantly influences the shear strength in the undrained test. The shear strength increases with the increase of the OCRs. Besides, the undrained effective stress paths are predominately governed by the OCRs. As shown in Fig. 6c, reasonable predictions of the normalized stress paths can be obtained by the proposed model. Particularly, the normalized stress paths form an envelope resembling a state bound surface. The shape of the surface is close to the elliptic shape of the yield surface of the MCC model on the wet side (\(\hbox{OCR} \leqslant 2\)), while similar to the nonlinear Hvorslev surface on the dry side (\(\hbox{OCR} > 2\)). This enables the constitutive model to predict a reasonable peak shear strength for heavily OC clays. These characteristics of the simulation are corroborated qualitatively by numerous laboratory tests.
5 Conclusions
Our mission is to develop a constitutive model, which is as simple as the MCC model but with better performance particularly for overconsolidated clays. We venture a formal comparison between our model and the MCC model in terms of formulation, number of parameters and model performance. Both MCC and our model possess simple formulation. However, the formulation of the hypoplastic model is even simpler than MCC model, since our model does not assume the separation of strain rate into elastic and plastic parts. Both model requires five model parameters, which can be easily determined from oedometer and triaxial tests.
The MCC model captures the salient features of normally and overconsolidated clays. Whereas the MCC model provides fairly decent prediction for normally consolidated clays, the prediction for heavily over-consolidated soil is rather crude. The stress-strain curve is characterized by an initially linear relationship until the yield surface is reached. Afterwards, the stress experiences strain softening toward the critical state. Similar observation can be made for the development of pore water pressure over strain, which decreases linearly (suction) until yielding. Upon yielding the pore water pressure changes abruptly to approach the pore pressure of the critical state. The effective stress path for heavily over-consolidated soils is discontinuous consisting a strain line under the yield surface and a subsequent segment leading to the critical state. Our model shows improvements across the board. The stress–strain, pore pressure–strain and the effective stress path are smooth. The hypoplastic model does not make use of the yield surface nor the hardening rule, which might be an advantage for numerical implementation.
References
Andresen A, Berre T, Kleven A, Lunne T (1979) Procedures used to obtain soil parameters for foundation engineering in the North Sea. Mar Geotechnol 3(3):201–266
Asaoka A, Nakano M, Noda T (2000) Superloading yield surface concept for highly structured soil behavior. Soils Found 40(2):99–110
Bauer E (1996) Calibration of a comprehensive hypoplastic model for granular materials. Soils Found 36(1):13–26
Bjerrum L (1967) Progressive failure in slopes of overconsolidated plastic clay and clay shales. ASCE J Soil Mech Found Div 93:1–49
Butterfield R (1979) A natural compression law for soils (an advance on \(e-{\text{ log }}p^{\prime }\)). Géotechnique 29(4):24–43
Dafalias YF, Herrmann LR (1986) Bounding surface plasticity II: Application to isotropic cohesive soils. J Eng Mech 112(12):1263–1291
Das A, Bajpai PK (2018) A hypoplastic approach for evaluating railway ballast degradation. Acta Geotech 13:1085–1102. https://doi.org/10.1007/s11440-017-0584-7
Fuentes W, Tafili M, Triantafyllidis T (2017) An ISA-plasticity-based model for viscous and non-viscous clays. Acta Geotech. https://doi.org/10.1007/s11440-017-0548-y
Fuentes W, Wichtmann T, Gil M, Lascarro C (2019) ISA-Hypoplasticity accounting for cyclic mobility effects for liquefaction analysis. Acta Geotech. https://doi.org/10.1007/s11440-019-00846-2
Gao ZW, Zhao JD, Yin ZY (2016) Dilatancy relation for overconsolidated clay. Int J Geomech 17(5):06016035
Gudehus G (2000) A comprehensive constitutive equation for granular materials. TASK Q Sci Bull Acad Comput Centre Gdansk 4(3):319–342
Hashiguchi K (1989) Subloading surface model in unconventional plasticity. Int J Solids Struct 25(8):917–945
He X, Wu W, Wang S (2019) A constitutive model for granular materials with evolving contact structure and contact forces Part I: framework. Granul Matter 21(2):16
He X, Wu W, Wang S (2019) A constitutive model for granular materials with evolving contact structure and contact forces Part II: constitutive equations. Granul Matter 21(2):20
Herle I, Kolymbas D (2004) Hypoplasticity for soils with low friction angles. Comput Geotech 31(5):365–373
Huang WX, Wu W, Sun DA, Sloan S (2006) A simple hypoplastic model for normally consolidated clay. Acta Geotech 1(1):15–27
Jocković S, Vukićević M (2017) Bounding surface model for overconsolidated clays with new state parameter formulation of hardening rule. Comput Geotech 83:16–29
Kolymbas D (1977) A rate-dependent constitutive equation for soils. Mech Res Commun 4(6):367–372
Li XS, Dafalias YF (2011) Anisotropic critical state theory: role of fabric. J Eng Mech 138(3):263–275
Lin J, Wu W, Borja RI (2015) Micropolar hypoplasticity for persistent shear band in heterogeneous granular materials. Comput Methods Appl Mech Eng 289(1):24–43
Mašín D (2005) A hypoplastic constitutive model for clays. Int J Numer Anal Meth Geomech 29(4):311–336
Mašín D, Herle I (2007) Improvement of a hypoplastic model to predict clay behavior under undrained conditions. Acta Geotech 2(4):261
Mašín D (2012) Hypoplastic cam-clay model. Géotechnique 62(6):549–553
Mašín D (2013) Clay hypoplasticity with explicitly defined asymptotic states. Acta Geotech 8(5):481–496
Mcdowell GR, Hau KW (2004) A generalised modified cam clay model for clay and sand incorporating kinematic hardening and bounding surface plasticity. Granul Matter 6(1):11–16
Niemunis A (2003b) Extended hypoplastic models for soils, volume 34. Institut für Grundbau und Bodenmechanik
Niemunis A (2003a) Anisotropic effects in hypoplasticity. In: Proceedings of the international symposium on deformation characteristics of geomaterials, volume 1. Lyon, pp 1211–1217
Pender MJ (1978) A model for the behavior of OC clays. Géotechnique 28(1):1–25
Peng C, Wang S, Wu W, Yu HS, Wang C, Chen J (2019) LOQUAT: an open-source GPU-accelerated SPH solver for geotechnical modeling. Acta Geotech 14(5):1269–1287
Porcino DD, Diano V, Triantafyllidis T, Wichtmann T (2019) Predicting undrained static response of sand with non-plastic fines in terms of equivalent granular state parameter. Acta Geotech. https://doi.org/10.1007/s11440-019-00770-5
Roscoe KH, Burland JB (1968) On the generalized stress-strain behavior of ‘wet’ clay. In: Proceedings of symposium on engineering plasticity. Cambridge Press, pp 535–610
Schofield A, Wroth P (1968) Critical state soil mechanics, vol 310. McGraw-Hill, London
Shi XS, Herle I, Bergholz K (2017) A nonlinear Hvorslev surface for highly OC clays: elastoplastic and hypoplastic implementations. Acta Geotech 12(4):809–823
Świtała BM, Wu W, Wang S (2019) Implementation of a coupled hydro-mechanical model for root-reinforced soils in finite element code. Comput Geotech 112:197–203
Tamagnini C, Viggiani G, Chambon R, Desrues J (2000) Evaluation of different strategies for the integration of hypoplastic constitutive equations: Application to the CLoE model. Mech Cohes Frict Mater 5(4):263–289
Tavenas F, Leroueil S (1980) The behaviour of embankments on clay foundations. Can Geotech J 17(2):236–260
Tafili M, Triantafyllidis T (2020) AVISA: anisotropic visco-ISA model and its performance at cyclic loading. Acta Geotech. https://doi.org/10.1007/s11440-020-00925-9
Tang Y, Wu W, Yin KL, Wang S, Lei GP (2019) A hydro-mechanical coupled analysis of rainfall induced landslide using a hypoplastic constitutive model. Comput Geotech 112:284–292
Von Wolffersdorff PA (1996) A hypoplastic relation for granular materials with a predefined limit state surface. Mech Cohes Frict Mater 1(3):251–271
Wang S, Wu W, Peng C, He XZ, Cui DS (2018) Numerical integration and FE implementation of a hypoplastic constitutive model. Acta Geotech 13(6):1265–1281
Wang S, Wu W, Yin ZY, Peng C, He XZ (2018) Modelling the time-dependent behavior of granular material with hypoplasticity. Int J Numer Anal Meth Geomech 42(12):1331–1345
Wang S, Wu W, Zhang DC, Kim JR (2020) Extension of a basic hypoplastic model for overconsolidated clays. Comput Geotech. https://doi.org/10.1016/j.compgeo.2020.103486
Wu W, Kolymbas D (1990) Numerical testing of the stability criterion for hypoplastic constitutive equations. Mech Mater 9(3):245–253
Wu W (1992) Hypoplasticity as a mathematical model for the mechanical behavior of granular materials. In: Publication series of the institute of soil mechanics and rock mechanics. Karlsruhe University, No, p 129
Wu W, Bauer E (1994) A simple hypoplastic constitutive model for sand. Int J Numer Anal Meth Geomech 18(12):833–862
Wu W, Bauer E, Kolymbas D (1996) Hypoplastic constitutive model with critical state for granular materials. Mech Mater 23(1):45–69
Wu W, Niemunis A (1997) Beyond failure in granular materials. Int J Numer Anal Meth Geomech 21(3):153–174
Wu W, Lin J, Wang XT (2017) A basic hypoplastic constitutive model for sand. Acta Geotech 12(6):1373–1382
Yang Z, Liao D, Xu T (2020) A hypoplastic model for granular soils incorporating anisotropic critical state theory. Int J Numer Anal Meth Geomech. https://doi.org/10.1002/nag.3025
Yao YP, Hou W, Zhou AN (2009) UH model: three-dimensional unified hardening model for overconsolidated clays. Géotechnique 59(5):451–469
Yao YP, Gao ZW, Zhao JD, Wan Z (2012) Modified UH model: constitutive modeling of overconsolidated clays based on a parabolic Hvorslev envelope. J Geotechn Geoenviron Eng 138(7):860–868
Yin ZY, Chang CS (2009) Non-uniqueness of critical state line in compression and extension conditions. Int J Numer Anal Meth Geomech 33(10):1315–1338
Acknowledgements
Open access funding provided by University of Natural Resources and Life Sciences Vienna (BOKU). The research carried out in this paper was funded by the H2020 Marie Skłodowska-Curie Actions RISE 2017 HERCULES (778360) and FRAMED (734485); the Erasmus+ KA2 project Re-built (2018-1-RO01-KA203-049214); and the Nazarbayev University Research Fund (SOE2017001). The first author wishes to thank the Otto Pregl Foundation for financial support in Austria.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Appendix
Appendix
The constitutive model is formulated as:
where the structure tensor \(\mathbf{S}\) is expressed as:
with the stress ratio R defined as
The multiplier \(f_u\) is expressed as:
In the proposed model, the material constants \(C_i\,(i=1,2,3,4)\) can be determined by \(E_i\), \(\nu _i\), and \(\phi _c\). The parameters N, \(\lambda ^*\), and \(\alpha\) are used to describe consolidation history. Since \(E_i\) can be scaled by \(\lambda ^*\), only five independent parameters are required.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Wang, S., Wu, W. A simple hypoplastic model for overconsolidated clays. Acta Geotech. 16, 21–29 (2021). https://doi.org/10.1007/s11440-020-01000-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11440-020-01000-z