Abstract
Since the solar irradiation is accessible in many parts of our planet, it is a viable replacement for fossil fuels, so commissioning photovoltaic (PV) power plants are increased, rapidly. One of the main problems that this technology faces is the increase in the temperature of solar cells. In this paper, streaming water layer over the upper side of PV modules is considered as a cooling method. This technique not only lowers the surface temperature, but also keeps the surface clean. Four different water flow rates of 0.5, 1, 2, and 4 lit/min were used so that two different flow patterns, water streaks and water film, were formed. In addition, the negative effect of the residual water layer over the surface of the PV panel on the absorbed radiation was evaluated experimentally. As results, temperature drops of 20.6 °C and 29.7 °C were measured for flow rates of 0.5 and 2 lit/min, respectively. Also, for the case of 4 lit/min, the efficiency is increased by 6.7% compared to the conventional case. Moreover, it was observed that after the formation of a water layer, the water flow rate no longer has a significant effect on cooling. Finally, a comparison between the electrical efficiency enhancements of this study with those of similar researches was performed.
Similar content being viewed by others
Data availability
The datasets used and/or analyzed during the current study are available from the corresponding author on reasonable request.
References
Abdolzadeh M, Ameri M (2009) Improving the effectiveness of a photovoltaic water pumping system by spraying water over the front of photovoltaic cells. Renew Energy 34:91–96
Akbarzadeh A, Wadowski T (1996) Heat pipe-based cooling systems for photovoltaic cells under concentrated solar radiation. Appl Therm Eng 16:81–87
Al-Shamani AN, Sopian K, Mat S, Hasan HA, Abed AM, Ruslan M (2016) Experimental studies of rectangular tube absorber photovoltaic thermal collector with various types of nanofluids under the tropical climate conditions. Energy Convers Manage 124:528–542
Al-Waeli AHA, Chaichan MT, Kazem HA, Sopian K, Ibrahim A, Mat S, Ruslan MH (2018) Comparison study of indoor/outdoor experiments of a photovoltaic thermal PV/T system containing SiC nanofluid as a coolant. Energy 151:33–44
Amber KP, Akram W, Bashir MA, Khan MS, Kousar A (2021) Experimental performance analysis of two different passive cooling techniques for solar photovoltaic installations. J Therm Anal Calorim 143:2355–2366
Bevilacqua P, Bruno R, Rollo A, Ferraro V (2022) A novel thermal model for PV panels with back surface spray cooling. Energy 255:124401
Castanheira AF, Fernandes JF, Branco PC (2018) Demonstration project of a cooling system for existing PV power plants in Portugal. Appl Energy 211:1297–1307
Darian MM, Ghorreshi A (2021) Comparison of the effect of temperature parameter on the functionality of tracking and fixed photovoltaic systems: a case study in Tehran, Iran. Scientia Iranica 28:1298–1305
Dorobanţu L, Popescu MO (2013) Increasing the efficiency of photovoltaic panels through cooling water film. UPB Sci. Bull. Series C 75:223–232
Du B, Hu E, Kolhe M (2012) Performance analysis of water cooled concentrated photovoltaic (CPV) system. Renew Sustain Energy Rev 16:6732–6736
Dubey S, Sarvaiya JN, Seshadri B (2013) Temperature dependent photovoltaic (PV) efficiency and its effect on PV production in the world–a review. Energy Procedia 33:311–321
Ewe W, Fudholi A, Yen C, Asim N, Sopian K (2019) Performance of solar air collector-thermoelectric hybrid system. IOP Conference Series: Earth and Environmental Science. IOP Publishing 268:012071
Firoozzadeh M, Shiravi AH, Lotfi M, Aidarova S, Sharipova A (2021a) Optimum concentration of carbon black aqueous nanofluid as coolant of photovoltaic modules: a case study. Energy 225:120219
Firoozzadeh M, Shiravi AH, Shafiee M (2021b) Thermodynamics assessment on cooling photovoltaic modules by phase change materials (PCMs) in critical operating temperature. J Therm Anal Calorim 144:1239–1251
Firoozzadeh M, Lotfi M, Shiravi AH (2022a) An experimental study on simultaneous use of metal fins and mirror to improve the performance of photovoltaic panels. Sustainability 14:16986
Firoozzadeh M, Shiravi AH, Chandel SS (2022b) An experimental analysis of enhancing efficiency of photovoltaic modules using straight and zigzag fins. J Therm Anal Calorim 147:8827–8839
Firoozzadeh M, Shiravi AH, Hodaei S (2023) An experimental approach on employing air flow through a porous medium as coolant of photovoltaic module: thermodynamics assessment. Therm Sci Eng Progress 40:101799
Fujii M, Yanagihara H, Mitsumoto S, Kikugawa S, Tokoro T, Fukuma M (2013) Improvement of conversion efficiency through water-cooled equipment in photovoltaic system. J Int Council Electric Eng 3:97–101
Goel V, Saxena A, Kumar M, Thakur A, Sharma A, Bianco V (2022) Potential of phase change materials and their effective use in solar thermal applications: a critical review. Appl Therm Eng 219:119417
Govardhanan M, Kumaraguruparan G, Kameswari M, Saravanan R, Vivar M, Srithar K (2020) Photovoltaic module with uniform water flow on top surface. Int J Photoenergy 2020:1–9
Hadipour A, Zargarabadi MR, Rashidi S (2021) An efficient pulsed-spray water cooling system for photovoltaic panels: experimental study and cost analysis. Renew Energy 164:867–875
Hosseini Rad A, Ghadamian H, Haghgou HR, Sarhaddi F (2019) Energy and exergy evaluation of multi-channel photovoltaic/thermal hybrid system: simulation and experiment. Int J Eng 32:1665–1680
Hu C, White RM (1983) Solar cells: from basic to advanced systems
Indartono YS, Suwono A, Pratama FY (2016) Improving photovoltaics performance by using yellow petroleum jelly as phase change material. Int J Low-Carbon Technol 11:333–337
Kadam V, Jagtap C, Alshahrani T, Khan F, Khan MT, Ahmad N, Al-Ahmed A, Pathan H (2021) Influence of CdS sensitization on the photovoltaic performance of CdS: TiO2 solar cell. J Mater Sci: Mater Electron 32:28214–28222
Kazem HA, Chaichan MT, Al-Waeli AH (2022) A comparison of dust impacts on polycrystalline and monocrystalline solar photovoltaic performance: an outdoor experimental study. Environ Sci Pollut Res 29:88788–88802
Kim J, Bae S, Yu Y, Nam Y (2019) Experimental and numerical study on the cooling performance of fins and metal mesh attached on a photovoltaic module. Energies 13:85
Kluth A (2008) Using water as a coolant to increase solar panel efficiency. California State science fair, California, USA
Krauter S (2004) Increased electrical yield via water flow over the front of photovoltaic panels. Sol Energy Mater Sol Cells 82:131–137
Larico ERA (2021) Wind energy potential by the weibull distribution at high-altitude Peruvian highlands. Int J Smart Grid-ijSmartGrid 5:113–120
Lee JH, Hwang SG, Lee GH (2019) Efficiency improvement of a photovoltaic thermal (PVT) system using nanofluids. Energies 12:3063
Lotfi M, Shiravi AH, Firoozzadeh M (2022) Experimental study on simultaneous use of phase change material and reflector to enhance the performance of photovoltaic modules. J Energy Storage 54:105342
Mahdi JM, Mohammed HI, Talebizadehsardari P (2021) A new approach for employing multiple PCMs in the passive thermal management of photovoltaic modules. Sol Energy 222:160–174
Mehrotra S, Rawat P, Debbarma M, Sudhakar K (2014) Performance of a solar panel with water immersion cooling technique. Int J Sci Environ Technol 3:1161–1172
Moharram KA, Abd-Elhady M, Kandil H, El-Sherif H (2013) Enhancing the performance of photovoltaic panels by water cooling. Ain Shams Eng J 4:869–877
Nasrin R, Rahim NA, Fayaz H, Hasanuzzaman M (2018) Water/MWCNT nanofluid based cooling system of PVT: experimental and numerical research. Renew Energy 121:286–300
Nateqi M, RajabiZargarabadi M, Rafee R (2021) Experimental investigations of spray flow rate and angle in enhancing the performance of PV panels by steady and pulsating water spray system. SN Appl Sci 3:1–13
Nižetić S, Čoko D, Yadav A, Grubišić-Čabo F (2016) Water spray cooling technique applied on a photovoltaic panel: the performance response. Energy Convers Manage 108:287–296
Pagodaripour A, Ghasemkhani A, Ghazizade-Ahsaee H, Namjo A (2020) The assessment and experimental study of photovoltaics panel by spraying water (case study: Kerman, Iran). Energy Equipment Syst 8:389–399
Pang W, Yu H, Zhang Y, Yan H (2018) Electrical characteristics of a hybrid photovoltaic/thermoelectric generator system. Energ Technol 6:1248–1254
Preet S, Bhushan B, Mahajan T (2017) Experimental investigation of water based photovoltaic/thermal (PV/T) system with and without phase change material (PCM). Sol Energy 155:1104–1120
Rajaee M, Ghorashi SMB (2015) Experimental measurements of a prototype high-concentration Fresnel lens and sun-tracking method for photovoltaic panel’s efficiency enhancement. J Theor Appl Phys 9:251–259
Sardarabadi M, Passandideh-Fard M, Heris SZ (2014) Experimental investigation of the effects of silica/water nanofluid on PV/T (photovoltaic thermal units). Energy 66:264–272
Saxena A, Agarwal N, Norton B (2021) Design and performance characteristics of an innovative heat sink structure with phase change material for cooling of photovoltaic system. Energy Sources Part A: Recovery Util Environ Effects 1–25
Sedaghat A, Karami M, Eslami M (2020) Improving performance of a photovoltaic panel by pin fins: a theoretical analysis. Iranian J Sci Technol Trans Mech Eng 44:997–1004
Shalaby S, Elfakharany M, Moharram B, Abosheiasha H (2022) Experimental study on the performance of PV with water cooling. Energy Rep 8:957–961
Sharaf M, Yousef MS, Huzayyin AS (2022) Review of cooling techniques used to enhance the efficiency of photovoltaic power systems. Environ Sci Pollut Res 29:26131–26159
Sharma S, Sellami N, Tahir A, Reddy K, Mallick TK (2015) Enhancing the performance of BICPV systems using phase change materials. AIP Conference Proceedings. AIP Publishing LLC 1679:110003
Shiravi AH, Firoozzadeh M (2022a) Performance assessment of a finned photovoltaic module exposed to an air stream; an experimental study. J Braz Soc Mech Sci Eng 44:535
Shiravi AH, Firoozzadeh M (2022) A novel proposed improvement on performance of a photovoltaic/water pumping system: energy and environmental analysis. Iranian (Iranica) J Energy Environ 13:202–208
Shiravi AH, Firoozzadeh M, Lotfi M (2022a) Experimental study on the effects of air blowing and irradiance intensity on the performance of photovoltaic modules, using central composite design. Energy 238:121633
Shiravi AH, Firoozzadeh M, Passandideh-Fard M (2022b) A modified exergy evaluation of using carbon-black/water/eg nanofluids as coolant of photovoltaic modules. Environ Sci Pollut Res 29:57603–57617
Sidiki A, Li W, Alhousseini M (2018) Experimental evaluation of the effect of inclination and dust deposition on production capacity of photovoltaic installations in West African Nations: case studyin Mali Drame. Iranian (Iranica) J Energy Environ 9:91–99
Sivakumar B, Navakrishnan S, Cibi MR, Senthil R (2021) Experimental study on the electrical performance of a solar photovoltaic panel by water immersion. Environ Sci Pollut Res 28:42981–42989
Smith MK, Selbak H, Wamser CC, Day NU, Krieske M, Sailor DJ, Rosenstiel TN (2014) Water cooling method to improve the performance of field-mounted, insulated, and concentrating photovoltaic modules. J Solar Energy Eng 136
Teo H, Lee P, Hawlader M (2012) An active cooling system for photovoltaic modules. Appl Energy 90:309–315
Tonui J, Tripanagnostopoulos Y (2007) Improved PV/T solar collectors with heat extraction by forced or natural air circulation. Renew Energy 32:623–637
Yildirim MA, Cebula A, Sułowicz M (2022) A cooling design for photovoltaic panels–water-based PV/T system. Energy 256:124654
Zilli BM, Lenz AM, de Souza SNM, Secco D, Nogueira CEC, Junior OHA, Nadaleti WC, Siqueira JAC, Gurgacz F (2018) Performance and effect of water-cooling on a microgeneration system of photovoltaic solar energy in Paraná, Brazil. J Clean Prod 192:477–485
Author information
Authors and Affiliations
Contributions
M. Firoozzadeh: investigation, methodology, writing—original draft, visualization.
M. Lotfi: writing—original draft, visualization, funding acquisition.
A. H. Shiravi: supervision, writing—review and editing, project administration.
M. Rajabzadeh Dezfuli: investigation, methodology, writing—original draft.
Corresponding author
Ethics declarations
Ethics approval and consent to participate
Not applicable.
Consent for publication
Not applicable.
Competing interests
The authors declare no competing interests.
Additional information
Responsible Editor: Philippe Garrigues
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Firoozzadeh, M., Lotfi, M., Shiravi, A.H. et al. An experimental study on using water streaks and water film over PV module to enhance the electrical efficiency. Environ Sci Pollut Res 31, 18226–18238 (2024). https://doi.org/10.1007/s11356-023-27117-8
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11356-023-27117-8