Abstract
The increasing demand for using competent and inexpensive methods based on biomaterials, like adsorption and biosorption, has given rise to the low-priced alternative biosorbents. In the past few years, Moringa oleifera (MO) has emerged as a green and low-priced biosorbent for the treatment of contaminated waters with heavy metals and dyes, and given its availability, we can create another generation of effective biosorbents based on different parts of this plant. In this review paper, we have briefed on the application of MO as a miraculous biosorbent for water purification. Moreover, the primary and cutting-edge methods for the purification and modification of MO to improve its adsorption are discussed. It was found that MO has abundant availability in the regions where it is grown, and simple chemical treatments increase the effectiveness of this plant in the treatment of some toxic contaminants. The different parts of this miraculous plant’s “seeds, leaves, or even husks” in their natural form also possess appreciable sorption capacities, high efficiency for treating low metal concentrations, and rapid adsorption kinetics. Thus, the advantages and disadvantages of different parts of MO as biosorbent, the conditions favorable to this biosorption, also, the proposal of a logical mechanism, which can justify the high efficiency of this plant, are discussed in this review. Finally, several conclusions have been drawn from some important works and which are examined in this review, and future suggestions are proposed.
Similar content being viewed by others
![](https://media.springernature.com/w215h120/springer-static/image/art%3A10.1007%2Fs11270-022-06010-z/MediaObjects/11270_2022_6010_Fig1_HTML.png)
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Avoid common mistakes on your manuscript.
Introduction
In the context of sustainable development and in parallel with the global economic crisis, the green chemistry “renewable substances” has caught the attention of various researchers around the world, particularly in developing communities. In general, the appearance of new water technologies known as “clean and friendly to the environment” using renewable and green materials of the biological entity to provide possibly the most efficient and convincing solution to the inherent problems in water and wastewater treatment.
In relation to this, over the last decade, many uncomplicated and captivating studies have been focused on the development of efficient bioprocesses relying on biomaterials including Moringa for the organic and inorganic metallic contaminant recovery/decontamination from the industrial effluent by biosorption (Pal et al. 2019; Benettayeb et al. 2017, 2021a, b, c; Hamza et al. 2020). Without forgetting that there are other types of effective treatment for the treatment of wastewater, such as photocatalyst (Islam et al. 2019).
The treatment cost of removing toxic heavy metals or dyes from real wastewater or even from synthetic aqueous solutions is very high. The management of this cost is related to the type of treatment applied to purify water but in the case of biosorption is substantially associated with the type of biosorbent. The treatment cost of the biosorption process in the elimination of pollutants can be managed efficaciously, especially when biosorbent is available at an attractive price.
So, biosorption is a physicochemical process wherein the uptake of a substance from a solution takes place by attachment to solid-phase biomaterial (Gadd 2009; Fomina and Gadd 2014). The biosorption has been effectively useful in the decontamination and the recovery of aqueous phase heavy metal ions and dyes (Awual 2015, 2016a; Hasan et al. 2021a). Several researchers have used effective materials to treat several toxic pollutants in wastewater, such as cerium(III) (Awual et al. 2013; Kubra et al. 2021), lead(III) (Awual 2016b; Benettayeb et al. 2017; Awual 2019a; Awual and Hasan 2019), copper(II) and phosphate (Awual, 2019b, c), cesium (Awual 2016c; Awual et al. 2020; Hasan et al. 2021b), selerium(IV) (Awual et al. 2015), and also some toxic dyes (Islam et al. 2021; Teo et al. 2022).
Knowing that the Moringa is a miraculous tree native to the foothills of the Himalayas (northern India, Pakistan, Bangladesh, and Nepal) and Africa (Anwar et al. 2007; Paliwal et al. 2011). The perspective sorption properties of all parts (seeds, leaves, barks, and husk) of this plant have been proposed by multiple research groups for the sequestration of the notable hazardous and toxic heavy metal ions (e.g., Cu(II), Ni(II), Pb(II), Cd(II), Hg(II)) in wastewater (Reddy et al. 2010a, b, 2012; Kebede et al. 2018; Çelekli et al. 2019; de Oliveira et al. 2019; de Bezerra et al. 2020; Gautam et al. 2020a). The metal ions have been declared as prioritized pollutants by many countries (Arora and Chauhan 2021). The increasing levels of toxic heavy metal ions generally discharged to the freshwater streams in developing countries, are continuously gaining tremendous attention due to their prominent adverse effects on receiving water bodies (Usman et al. 2018b). In order to provide the environmental sustainability of freshwater resources, environmental researchers are constantly interested in cheap and locally available biomaterials like Moringa, which are not only effective for water treatment but also resistant to use at different conditions of wastewater treatment. So far, researchers are trying to find new MO-based biosorbents to improve their pollutant removal/recovery capacity as well as their selectivity toward some toxic pollutants.
This review will enlighten the reader’s vision about the importance of the Moringa tree, citing its potential uses in various fields, especially their importance in the field of water treatment. So, this review regroups a succinct overview of important information related to the use of Moringa in modern applications, mainly the depollution using different MO-based adsorbents, their waste management capability, as well as search for optimal operational conditions related to its use in the former field of application. The regrouped information are summarized and holistically discussed in this review. Additionally, we propose a mechanism, which justifies its effectiveness with the precision of the groups/functions, which participate in these mixed biosorption mechanisms for some pollutants (CV, BG, and Pb(II)). In the end, the comments and recommendations on future developments are provided, and an attempt is made to identify gaps in knowledge and future perspectives on the use of MO derivatives.
Moringa and its species
Moringa is the subject matter of this research review that is a source of proteins; mostly, its seeds are sources of proteins, lipids, fats, soluble vitamins, antioxidants, and other components (Saa et al. 2019). The different types of Moringa available in Mali such as Moringa stenopetala, MO, and Moringa drouhardii are shown in Fig. 1. Accordingly, Fig. 1 represents the different types of Moringa available in Mali.
Different parts of the MO are represented in Fig. 2. All parts of the Moringa plant, particularly “MO leaves (MOL),” “MO seeds (MOS),” “MO bark (MOB),” and “MO husk (MOH)” are effective in the treatment of wastewater (Vieira et al. 2010; Soliman et al. 2019; Verma et al. 2020). Bearing in mind that this plant MO, especially its seeds MOS, as a good coagulant, is still being used till the current days (Taiwo et al. 2020; Vega Andrade et al. 2021). But usually, all the parts of this plant are used as natural biosorbents (Reddy et al. 2010a, 2012; Vieira et al. 2010; Acheampong et al. 2011; Mnisi and Ndibewu 2017; Adebayo et al. 2019; de Oliveira et al. 2019; Soliman et al. 2019; Verma et al. 2020).
General uses of Moringa oleifera
As a mother’s best friend, MO is a tree with multiple benefits: medicinal, nutritional, and even industrial. Also, several authors have discussed its importance in food, animal feed, pharmacology, and cosmetics (Mahmood et al. 2010; Gopalakrishnan et al. 2016; 2019; Meireles et al. 2020). The main areas of this plant’s uses are (1) food; human nutrition and animal feed; (2) traditional medicines for the treatment of human diseases; (3) cosmetics and beauty products; (4) beekeeping; (5) soil protection; (6) water purification; (7) crop fertilization and biostimulant; (8) pesticides; (9) industry in various domain, and (10) landscape art.
MO is a medicinal plant widely used in folkloric medicine of Africa and Asia for the treatment of ailments such as ulcer, wound, inflammation, heart problem, cancer, stroke, obesity, anemia, and liver damage (Aja et al. 2014). Also, traditional Indian medicine (Ayurvedic) says that MO can prevent 300 diseases and that its leaves have been exploited for preventive and curative purposes (Ganguly 2013). In addition, a study in India indicates that MO is one of the species used by traditional Siddha healers (Mutheeswaran et al. 2011). While the ancient Egyptians used MO oil on the skin due to its cosmetic properties (Mahmood et al. 2010). The details of the famous uses of MO are summarized in Table 1. The use of the natural grain of MO for adsorption of crystal violet (CV) and brilliant green (BG) is shown in Fig. 4, while the advantages and disadvantages of MO in biosorption are summarized in Fig. 3.
Some preparation methods of the Moringa oleifera leaf, seed powder, seeds pretreatment, and the protocol of extraction of the oils of the seeds
The transformation process of MO is depending on its intended use. However, the main steps followed for the production of seed powder and husks, leave powders are dedicated in Fig. 5. For the production of the powder of leaves and husks, which was mentioned in the article by Benettayeb et al. (2021a, b, c), first, the seeds were shelled, and after, the leaves, seeds, and husks were washed with distilled water and dried in an oven at 40 °C for 48 h. Then grounded, and the powder obtained was dried at 50 °C for 30 min to reduce the residual moisture below 7.5% (Benettayeb and Haddou 2021).
The MO seeds contain a percentage of oil that can possibly be extracted. During oil extraction, the cake obtained as a by-product is very rich in protein and some of these proteins can be used as a source of flocculants and adsorptive materials for the sorption of various element toxic pollutants including heavy metals in water treatment (Baptista et al. 2017). Therefore, the method of oil extraction seems to be a decisive step for the intended use of the obtained cake as an adsorbent of pollutants.
For the preparation of MO seeds for oil extraction, the MO seeds are shelled classically by hand, and peeled seeds of the MO are washed carefully with distilled water to eliminate all traces of dirt. The washed peeled seeds “kernels” are dried in an oven at 40 °C for 24 h. The peeled MO seeds are pulverized with mortar and pestle, and the oil is extracted by Soxhlet extraction, and the separation of the oils/solvent is performed by simple distillation because the boiling temperature of the solvent used “hexane” is 69 °C (Benettayeb and Haddou 2021).
The resulting solid extracts are dried at room temperature in the open air for 1 h. The residue obtained after extracting the seed oil, generally known as “MO flour or MO powder,” is dried at 60 °C for 24 h and after is stored at room temperature. According to Benettayeb et al. (2021a, b, c), it has been found that the percentage of the protein content of the peeled MO seeds before and after oil extraction is different (Benettayeb and Haddou 2021). Indeed, increasing the rate of oil recovery allowed to increase the rate of protein in the residue, such an operation might favor the coagulant effect of MO flour solutions and increase the biosorption efficiency in most cases (Benettayeb and Haddou 2021).
Moringa oleifera for treatment of contaminants of water and wastewater
The use of MO as a biosorbent in ecological green processes to treat water, domestic wastewater, and industrial effluents has become increasingly popular as it is an environmentally friendly and innovative natural biomaterial. The biosorption process involving MO adsorption can offer many advantages such as cost reduction, reduction of by-product production as the cake generated during oil extraction will be utilized and increase the biodegradability over other decontamination processes (Villaseñor-Basulto et al. 2018) as well as the efficiency compared to other equivalent processes that utilize expensive organic products synthesized.
Aside from biosorption, which is the objective of this study, to eliminate the danger of toxic contaminants from water and wastewater, numerous treatment technologies have been used and developed in the decontamination/recovery of pollutants during the last few years. For example, ion exchange, biological treatment, coagulation (Mateus et al. 2018; Ngineering et al. 2019), membrane adsorption (Khulbe and Matsuura 2018), chemical precipitation (Son et al. 2020; Zhang and Duan 2020), solid-liquid separation using porous membranes (Usman et al. 2020a; Xu et al. 2021), membrane bioreactors (de Lopes et al. 2020), complexation (Trivunac and Stevanovic 2006; Deblonde et al. 2018), sorption on chemically synthesized and natural materials (Burakov et al. 2018; Ngabura et al. 2018; Šoštarić et al. 2018; Usman et al. 2018a), and reverse osmosis (de Lopes et al. 2020; Samaei et al. 2020; Cai et al. 2021) were used for wastewater treatment and decontamination. These technologies, except for adsorption, conventionally used in wastewater treatment, give low efficiency, complex installation, high operating costs, high energy requirements, and the generation of toxic secondary sludge (Araújo et al. 2010b, 2018). However, due to the new periodic demands and requirements, adsorption is the most widely used one because it still offers several advantages (Naushad 2014; Albadarin et al. 2017) (see Fig. 3) and is still known as a potential technology that is generally accepted as environmentally friendly and inexpensive for water treatment due to its ease of operation and maintenance, cost-effectiveness, simplicity of design, high efficiency and performance potential, flexibility, speed, and availability of diversified sorbents effective for each pollutant (Gopalakannan and Viswanathan 2015).
Despite being the simplest operation for treating toxic pollutants, the effectiveness of this technology strongly depends on the environment of the solution (temperature of the water, which intervenes in the matrix of the adsorbent, pH) and adsorptive medium (biomaterial and the products involved in the synthesis of the adsorbent) applied (Peng and Guo 2020). The efficiency of the adsorptive materials like MO is too sensitive to some parameters including nature and the origin of biosorption material, particle size, effective surface area, surface charge density, and pretreatment before use.
Moringa oleifera as miraculous biosorbent
The data used to create Fig. 4a and b was collected from Scopus using the keywords of Moringa adsorption or removal of pollutants by Moringa and Moringa as potential adsorbents for metals and dyes. In the period 2016 to 2021, the Scopus database yielded 819 papers that investigated the potential of Moringa as an adsorbent for the removal of heavy metals and organic dyes. Figure 4 demonstrates that the use of Moringa as an adsorbent is increasing, especially since the number of studies published in 2021 is 347 (compared to the year 2016 with 60 papers). Figure 4b exhibits that it is mostly applied for decontamination of dyes (BG, CV) followed by Cu(II) ions and after Cd(II) ions, these data show that this plant is very important in the fields of adsorption, and can be used to create other generation of bioadsorbents (Benettayeb and Haddou 2021).
MO biomass has also been reported to bind some pollutants such as cationic dyes and metal ions through amino and carboxylic groups present in proteins, sulfonic groups (–SO3−), and other constituents in the seeds or the leaves of this plant. Figure 5 presents an example of MO seeds biosorption comparison before and after 24 h of biosorption of crystal violet (CV) and brilliant green (BG).
The functional groups on the surfaces of the biosorbents, especially function –N, –S can easily adsorb heavy metal ions, these functions provide selective and effective adsorption for various metal ions, which belong to class B such as (Hg(II), Ag(I), Pd(II), Pt(IV), Pt(III), Au(III), Cs(I)), and intermediate (borderline) according to the classifications of Pearson (1990) and (Nieboer and Richardson 1980). Also, MO contains a high percentage of lignin that is a heterogeneous complex biopolymer molecule, which is endowed with many different functional groups, such as methoxy, hydroxyl-aliphatic, carboxyl, and phenolic (Eun and Rowell 2005). For example, during the introduction of the −NH2 groups into the structure of the alginate by simple voices, an improvement in sorption for the ions of Pb(II), Cd(II), and Cu(II) was noticed (Benettayeb et al. 2017). Lin et al. demonstrated that the adsorbents with amine groups have special properties that enable them to adsorb compounds with cationic or anionic charges at different pH values (Lin et al. 2011). Similar conclusions were drawn by Sahebjamee et al. (2019). These studies confirm the importance of –NH2 in the adsorption of metals ions and toxic dyes on adsorptive materials including MO. Further studies revealed that the MO biomass residue can be used for the removal of pharmaceutical molecules such as diclofenac (DCF) from water (Araujo et al. 2018), which gave a Qmax of 72.8 mg g−1 obtained by electrostatic attraction between the negative groups (O−, OH−, and Cl−) of the DFC and the functional positive groups present on the surface of the adsorbent at a pH value of 5 (Araujo et al. 2018). The virgin MO seeds and husk as biosorbents have been exploited for the adsorption of trihalomethanes (Okoya et al. 2020). Table 2 summarizes the adsorption capacities of MO including all parts of it and its other species for the removal of some undesired pollutants from wastewater. Figure 6 diagram summarizes the process of production of the MO powder (MOP) from MOS, MOL, and MOH represented in Benettayeb and Haddou (2021).
Moringa oleifera as a coagulant
Also, MO is known for its attractive properties in wastewater treatment by coagulation, flocculation, and biosorption; this concept will reduce the environmental impact of hazardous chemicals used for the purification of contaminated water. Therefore, it might be a remedial solution in rural areas facing water scarcity where there are no resources to obtain expensive conventional techniques and materials. Mataka et al. reported that Moringa stenopetala flour showed better coagulant performance compared to MO in the removal of Pb(II) at pH 10.0, a dose of 15 g/L and 100 °C (Mataka et al. 2006). However, Obuseng et al. have obtained 95% removal efficiency of Pb(II) in water having a pH value of 2.0, a dose of coagulant 5 g/L, and a temperature of 22 °C using MO seed flour (Obuseng et al. 2012). Another research performed by Kebede et al. (2018) studied the elimination of Cd(II), Pb(II), and Cu(II) ions from industrial effluent using Moringa stenopetala seed powder in its natural form. The maximum Langmuir adsorption capacity (Qmax) was found to be 233, 16.1, and 10.2 mg g−1 for Cd(II), Pb(II), and Cu(II), respectively, and reported adsorption efficiencies of all pollutants were in the range of 99–100% from synthetic wastewater. The removal efficiencies in complex wastewaters comparing industrial effluent were approximately 92–95% (Kebede et al. 2018).
Effect of modification of Moringa oleifera on some famous toxic pollutants
The structure of the biosorbent plays an important role in the biosorption process. The smaller is the pore size, the larger is the contact area of the biosorbent. It is therefore realistic to use a predominantly microporous biosorbent to obtain a good adsorption capacity as is the case with MO. The manufacture of bioadsorbents based on the different parts of MO varied from simplicity (simple modification method) to the synthesis of biosorbents using the complex method (several cascade reactions, to mix the properties of several materials).
The modification of MO-based biosorbents has been made to improve their affinity toward target pollutants and uptake rate as well as to improve their selectivity and to optimize (for example, surface area, adsorption capacity) or expand (for example, the composition of surface functional groups to remove the metal ions that are less or not adsorbed by pristine MO). There are several ways, which can be undertaken for the modification of MO. Indeed, modification methods include physical treatment modification, chemical treatment modification, functionalization/grafting/cross-linking, and impregnation. After this modification, the obtained results depend on the modification agent and the modification way. Table 2 shows the adsorption capacities of both pristine and modified MO-based biosorbents.
Tables 2 and 3 demonstrate that the nature and intrinsic characteristics of MO leaves, seeds, and husks have an effect on biosorption; habitually, the researchers apply pretreatment processes to modify or affect some of their properties inherent in biomaterials in order to promote the biosorption process. According to these researchers, the pretreatment processes that have been frequently practiced by various research groups include grinding, boiling, autoclaving, and acid/alkali processing (Reddy et al. 2010a, b, 2011, 2012; Araújo et al. 2010a; Acheampong et al. 2011; Marques et al. 2012; Raj et al. 2013; Mnisi and Ndibewu 2017; Adebayo et al. 2019; Çelekli et al. 2019; de Oliveira et al. 2019; Gautam et al. 2020a).
Various researchers have cited the contributions of the chemical modification even though it was a simple chemical treatment and their positive effect on the structure of MO. In the work of de Bezerra et al. (2020) for the removal of diuron, a herbicide from contaminated water, the MO husk (MOH) powder, was chemically treated with two acids. After this chemical treatment, a thermal treatment was performed as a second step to remove some inorganic or organic matters from the MO surface. These matters are considered impurities, which interfere in the interaction of the contaminant with the surface of the biosorbent and increase the surface area (de Bezerra et al. 2020). Cusioli et al. explored the chemical modification of MO lam seed husks. The chemical modification (by 0.1 M of CH3OH for 4 h in a 1:5 m/v ratio and 0.1 M of HNO3 for 1 h) following thermal treatment of produced biomaterial was carried out for 12 h. The chemical modified MO powder was subsequently used for atrazine removal. It was proven to be effective by demonstrating Qmax of 10.321 mg/g under the following conditions: temperature of 318 K, pH of 5, and a mass of 0.04 g. The equilibrium was reached at 1200 min, and the authors confirmed that the process of biosorption occurs by chemisorption and physisorption mechanism together (Cusioli et al. 2019).
According to the work of Bhatti et al., the efficient removal of zinc from aqueous solution was observed using MO lam. The MO lam was chemically pretreated, and the obtained sorption capacity was about 52.1 mg/g (with an efficiency of 90% at a time of 50 min). The adsorption test was investigated at 30 °C and pH of 7.0 (Bhatti et al. 2007). In another study, MOL were used as an effective biosorbent for treating solutions having low concentrations of Cd(II) (1, 3, 5 up to 7 mg L−1) without a modification or any kind of chemical treatment, the authors confirming that this powder has a considerable high biosorption capacity (Ali et al. 2015).
In the work of Gautam et al., the authors made new magnetic nanoparticles based on MO, which have proven to be effective for the biosorption of lead ions. The results obeyed the Freundlich isothermal adsorption with a maximum capacity of 64.97 mg/g (with an efficiency of 94.08%) at a temperature of 50 °C, pH 5.0, and a time of 60 min (Gautam et al. 2020b). To improve the chelation of heavy metal ions such as Pb(II), Cd(II), Cu(II), and Ni(II) from aqueous in batch systems studies, it has been found that citric acid and NaOH modification of MO enhances the uptake of these metal ions (Reddy et al. 2010a, 2012).
The researchers tested the efficacy of MO seeds (natural, particle sizes from 75 to 500 μm) toward Ag(I), Cd(II), Co(II), Cu(II), and Pb(II) at a concentration of 5.0 mg L−1, 2 g of adsorbent, contact time of 20 min, a temperature of 25 °C, and pH of 6.5. The best efficiency was achieved for Ag(I), and the efficiency varies from 28 for Co(II) to 100% of Ag(I) and demonstrate following the order: Ag(I) > Pb(II) > Cu(II) > Cd(II) > Co(II) (Araújo et al. 2010a). In this work, the seeds were dried at 65 °C for 24 h and used directly without any further treatment (Araújo et al. 2010a).
The biosorption of Pb(II) by MOL has been as well and obtained Qmax is 45.8 mg/g (at an adsorbent dosage 1.5 g/L), while this biosorbent achieved 98.6% removal of Pb(II) at an MOL dose of 10 g L−1 and pH 6. After five biosorption/desorption cycles (using 0.3 M HCl solution as desorbing agent), an 8% decrease in the removal efficiency of MOL for Pb(II) was realized (97% to 89%) (Imran et al. 2019).
Several ways of modification have been used in the manufacture of new materials based on polysaccharides “such as alginate, chitosan,” but in the case of MO, despite the richness of this plant (source of different protein), little work has been done to find new ways to modify this plant. A comparison was made by Abdeen (2018) between the biosorption efficiency of chitosan and MO against some metal ions and stated that the affinity of MO seeds was in the following order: Cd(II) > Mn(II) > Cu(II) > Ni(II) > Zn(II) > Fe(II) > Pb(II). While the affinity of chitosan was Cd(II) > Cu(II) > Ni(II) > Zn(II) > Mn(II) > Fe(II) > Pb(II). The elementary analysis of Moringa seeds and chitosan showed, respectively, a percentage of –N of 6.2 and 7%, but for the elements Ca, Mg, and Na, the chitosan is rich compared to Moringa (Abdeen 2018). The highest percentage removal of Fe, Zn, Mn, and Cu by using MOS extract was 45.74% Fe, 46.15% Zn, 64.29% Mn(II), and 47.37% Cu(II). Other studies demonstrated the same outcomes (Sajidu et al. 2005; Subramanium et al. 2011). There is a new method of making MO beads from Algerian olive oil using a cold gelation method and MO from Mali; these beads were based on MOS, MOH and MOL, and gelatin. It was shown that beads own great efficiency with respect to CV, BG, and Pb (II) ions at the range of a pH value of 5–6. The removal efficiencies varied from 38 to 83% depending on the modification and the pollutant type. It is relevant to state that the EDX analysis showed the highest percentage of amino groups and the FT-IR spectra showed the existence of various functional groups such as, –NH, –OH, and –COOH (Benettayeb and Haddou 2021).
Methods for efficient characterization of biosorption
Analytical characteristics
The characterization of different MO products is essential for an attempt to explain their behavior, thus establishing a complete data sheet for each solid requires a series of analyses such as X-ray diffraction (XRD), Fourier transformed infrared spectroscopy (FTIR), scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDX) analysis, and ATD/ATG thermal analysis.
This list of analyses depends on the type of biomaterial considered, its origin, the type of modification carried out as well as the envisaged application. For example, in the case of MO leaves modification to obtain a nanopowder, researchers carried out some specific analyses like SEM/SEM-EDX, Brunauer, Emmett, and Teller (BET) surface area, FTIR, and XRD.
Several analytical methods have been used to characterize this type of biosorbent: FTIR analysis, the morphology, and semiquantitative composition of the materials synthesized have been visualized by SEM. In several works, the composition of the beads was determined using SEM-EDX.
Generally, analytical methods like; FTIR, SEM/TEM, and SEM-EDX are needed to understand the morphology, composition, and distribution of elements in the adsorbent surface. The importance of FITR spectra has increased in the sorption domain and particularly in the biosorption because they can facilitate understanding the sorption mechanism and steps involved, as the identification of functional groups (active sites) in biosorbent suggests the ability to make bonds with them in the biosorption process, so we can understand approximately how each pollutant makes the choice of active sites/adsorbents.
Knowing that, FTIR spectroscopy provides a means of measuring low-frequency vibrational movements, which are useful for characterizing many organometallic and inorganic molecules. The results of these measurements often allow one to approximate the chemical nature and molecular structure of an organometallic complex. Also, the FTIR analyses before and after biosorption are very important because the change in transmittance in FTIR spectra for metal-loaded MO indicates that these functional groups are involved in biosorption. (Ahmady-Asbchin et al. 2008) confirmed that biosorption of metals to biosolids results in a decrease in absorbance compared to the raw sample.
The analysis TGA/DCS supplies information about the thermal stability of biosorbent (Fomina and Gadd 2014). According to Araújo et al. (2010a), the thermogravimetric analysis was used to characterize the decomposition stages and thermal stability of the MO seeds, some methods adopted by these researchers for the characterization of MO seeds are FTIR spectroscopy, thermogravimetric analysis (TGA), XRD, and SEM and confirmed that these are sufficient for this type of biosorbent.
Physical characterization
Physical characteristics such as humidity rate, swelling rate, amino rate, real density, apparent density, total pore volume, and chemical porosity for the precision of the functional groups in the surface of prepared materials are determined by using a simple protocol. Generally, the titration methods can give important information about the existence of some active sites (or some components like –NH2, –COOH, and phenolic content) in the surface of the biosorbent and their concentration/quantity.
-
a)
Estimation of humidity rate and swelling/deswelling rate
In order to determine the percentage of water content (W%) maintained intrinsically in the structural form (for example in the beads), while determining the percentage of swelling (S%), the beads are left for 24–72 h in distilled water. The sample is weighed when it is wet, then after 72 h reweighed, and the moisture content (W%) is calculated by Eq. 1. For the % swelling rate, the sample is weighed when it is dried, then after 24–72 h weighed again, and the rate of swelling is calculated by Eq. 2.
where WW: mass or weight of wet beads after 72 h and Wd: mass or weight of the beads after 72 h of drying.
-
b)
Estimation of real density, apparent density, total pore volume, and chemical porosity
While for the actual density, a small amount of known mass (g) is put into a tared pycnometer, which is filled with methanol. Knowing the volume of the pycnometer\({\boldsymbol{v}}_{\mathbf{m}}=\frac{{\boldsymbol{m}}_{\mathbf{2}}}{{\boldsymbol{\rho}}_{\boldsymbol{m}}}\), the mass of the material used and the density of methanol (ρm), makes it possible to calculate the real density (ρréelle) of the biomass using Eqs. 3 and 4.
where ml and m2 represent the mass (g) of material and methanol, respectively; mt represents total mass (material + methanol); Vt represents the total volume of the pycnometer, ρm denotes the density of methanol at measurement T and P (25 °C and 1 atm) = 0.7864 g/cm3; Vm represents the volume of methanol used; and VR represents the actual volume of the material.
For apparent density, the method used consists of introducing a quantity of sample corresponding to any apparent volume into a previously washed and dried test tube. To prevent the powder from sticking to the walls of the specimen, it is necessary to shake the assembly in order to obtain a good settlement of the latter. Knowing the mass of the sample (m1) and the apparent volume (Vapp) provides access to the apparent density (ρapp) of the material. The total pore volume of the sample “V.P.T” is calculated from the apparent and real densities (see Eq. 6).
For the determination of active sites and the calculation of the percentage of functional groups like –NH2, –COOH, and other groups on the surface of MO before and after modification can be performed the analytical methods like volumetric titration.
-
c)
Estimation of content of carboxylic groups
Various analytical methods have been used by several researchers in order to know the percentage of new functions or those existing in the adsorbent. In the case of the estimation, by calculation, of the content of carboxyl function, the methods reported in (Atia et al. 2005c, a) can be exercised. For instance, (Atia et al. 2005c, a) reported that 0.005 g of the biosorbent is stirred in 50 mL of 0.2 M aqueous NaOH solution at a temperature of 25 °C for 6 h. The mixture is then filtered, and the concentration of unreacted NaOH is determined by titration of 20 mL of the filtrate with 0.2 M HCl. Therefore, the concentration of carboxyl groups (mmol/g) in the solid is calculated by Eq. 7, knowing that, the M1 and M2 are the initial and final concentrations of NaOH, V is the volume of NaOH, and W is the weight of the adsorbent.
-
d)
Estimation of the content of amine groups
The amine content of chemical materials including biosorbents has been estimated using a volumetric method (Atia et al. 2005b; Donia et al. 2012; Elwakeel et al. 2014). Briefly, 50 ml of 0.2 M HCl solution is added to 0.005 g of biosorbent for 15 h providing constant stirring. The residual HCl concentration is estimated by titration against the 0.2 M NaOH solution using phenolphthalein as a colored indicator. The number of moles of HCl having interacted with the amine groups, and consequently, the concentration of amine groups (mmol.g−1) is calculated from Eqs. 8 and 9.
-
e)
Estimation of the total content of phenolic
Gautam et al. (2020b) adopted a procedure for the determination of the total phenolic content of MO by preparing extracts of its leaves. In the first step, 10 g of dried fine leaf powder was mixed with 200 ml of ethanol in a volumetric flask for 24 h at room temperature. The resulting solution was filtered using filter paper and dried the supernatant in a vacuum at 40 °C using a rotary evaporator. The second step is the mixture of 0.5 mL of synthesized plant extract in 2.5 ml of 10% Folin–Ciocalteu’s reagent and 2.5 mL of 7.5% NaHCO3 and kept the same for incubation at 45 °C for 1 h. Blank was also prepared in a similar way.
The absorbance (λmax) of the sample was determined at 760 nm. The sample concentration was determined from the profile of the gallic acid calibration curve using a gallic acid concentration of 0.01 to 0.12 mg/L, and the total phenolic content was measured using Eq. 10 (Gautam et al. 2020b).
where C is the concentration of the calibration curve derived from the standard curve equation: Y = ax + b; Y is the absorbance at 760 nm; and xp is the total phenolic content, V (mL) is the volume of extract used, and M (g) is the mass of the extract used. The total phenolic content was calculated to be 111.61 mg/g of gallic acid equivalent. Knowing that, we must obtain a calibration curve with an R2 greater than 0.999.
Effect of operational parameters in biosorption by Moringa oleifera
The biosorption process can be carried out in two modes: batch mode and continuous mode (column). The batch process is frequently used to perform biosorption processes on a laboratory scale. However, most industrial applications prefer continuous mode biosorption. However, batch experiments are used to assess the basic information required such as the efficiency of the biosorbents toward a specific substance, optimal experimental conditions (contact time, Temperature, initial adsorbate concentration, amount of biosorbent applied, and other parameters), the biosorption rate and the possibility of spent biosorbent regeneration.
Also, the size of the molecule and ion acting as adsorbate can greatly influence the adsorption process by their arrangement on the surface of the material because the particles with low molecular mass are light and move faster. The so-called batch method is shown schematically in Fig. 7. When the peeled MO seeds in their natural form are applied we can use magnetic agitation or even use mechanical agitation.
Effect of pH
It is a prerequisite to know the efficiency of the biosorption of biosorbents at different pH conditions to determine the effective range of pH on the biosorption in order to carry out this step.
Choosing the right pH value for each material can affect the biosorption process because the variation in pH conditions of water can cause group modification as well as affect the surface charge of biosorbents and consequently, increase or decrease the sorption efficiency. Therefore, the value of pH plays a major and direct role in the study of pollutant sorption phenomena. The value of pH can affect the solution chemistry of the pollutant, the activity of the functional groups in the biomass, and the competition of ions for binding sites (Adeniyi and Ighalo 2019).
In general, the surface charge potential of the adsorbents, the protonation/deprotonation behavior of the adsorbate, and the interaction mechanism between the undesired adsorbate and the adsorbent used to change depending on the pH of the water being processed for decontamination. These parameters are the decisive factors influencing the biosorption process. It should be noted that the solution pH is an important criterion since it may affect the metal/dyes speciation through the formation of complexes (in presence of ligands), which, in turn, influence the binding mechanism. Furthermore, it can also induce precipitation phenomena (Benettayeb et al. 2017). Besides, the solubility of the metal ions will depend on the total metal concentration and the equilibrium pH value. Indeed, sorbent-solution interaction may increase the pH of the solution (by proton binding, for example) (Benettayeb et al. 2017).
Cr(VI) adsorption was studied as a function of pH over a range of 2–8 for Moringa stenopetala seed powder (MSSP) at an initial concentration of 30 mg/L wastewater. The results of the experiment indicate that optimal Cr(VI) removal efficiency of MSSP was obtained at pH 2.0 for 120-min contact time. It is evident that Cr(VI) removal efficiency increases with a decrease in pH. The favorable effect at low pH might be due to the neutralization of negative changes on the surface of Moringa by excess hydrogen ions, thereby facilitating the diffusion of the hydrogen chromate ion (HCrO4−) (Badessa et al. 2020).
Most researchers use NaOH to raise the solution pH. However, other bases are preferred because the addition of NaOH can result in the formation of insoluble complexes, which causes precipitation at low pH values and low concentrations of undesirable substances. Thereby, deformation of the sorption results occurred.
pH of zero point charge (pHpzc)
The initial pH value of the solution is an important factor affecting the sorption of the pollutant. This parameter can change the adsorbent surface density. The pHpzc (known as pH at point of a zero charge) corresponds to the pH value for which the charge on the material surface is zero. Classically, the pHPZC is reckoned using the “pH drift method” (K. Kadirvelu and C. Faur-Brasquet 2000). This method states that the pHpzc is the point where the initial pH curve as a function of the final pH intercepts the line corresponding to pHinitial = pHfinal; in fact, the pHpzc represents the border where the surface charge is zero and changes sign. The pHzpc also can be determined by following the variation of pHi = f(pHeq) during the isotherm studies, pHpzc corresponding to the point of intersection of the experimental curve (final pH as a function of initial pH) with the linear plot (pHi = pHf). This method has been used in many studies (Lopez-Ramon et al. 1999; Kadirvelu and C. Faur-Brasquet 2000; F. Boudrahem and F. Aissani-Benissad 2011).
When pH > pHpzc, it indicates the net material surface charge is negative (to promote the adsorption of cationic substances). When pH < pHpzc, the net material surface charge reckoned is to be positive (to promote the adsorption of anionic substances). So, this indicates that below this solution pH, the adsorbents are positively charged, while above this solution pH, the surface of the modified adsorbents is negatively charged (see Fig. 8).
The pHpzc of the MO seeds is within the range of 6 to 7 (Araújo et al. 2010b). In another work, the pHpzc of MO seeds was found to be 4.5 by Çelekli et al. (2019). Reddy et al. (2012) found a pHPZC of 3.7 ± 0.2 in the case of modified MO leaves for the removal of Cd(II), Ni(II), and Cu(II). In another work, pHPZC of pristine MO leaves is 5.5 ± 0.2. Prior to pHPZC determination, MO leaves were carefully washed with distilled water to eliminate adhering dirt and particulate materials and dried in the air and then in the oven at 70 °C for 20 h (Imran et al. 2019). These differences in pHPZC values may be due to the procurement of MO from varying origins, the method of analysis of pHPZC as well as the initial treatment, which varies from one researcher to another and other parameters.
Effect of temperature on sorption by Moringa oleifera
In most cases of studies reviewed in this paper, the biosorption capacity of Moringa-based biosorbents is temperature sensitive and is enhanced with increasing temperature. The MO biosorption is affected by temperature moderately at medium temperatures (20–35 °C) and greatly at higher temperatures, and these authors confirmed that the biosorbent (precisely the MO leaves) can be severely denatured at increased temperature (Adeniyi and Ighalo 2019). Although we must take into account that the increasing temperature of adsorbate solution may not necessarily increase sorption active sites over the surface of the adsorbent but may generate a new pathway that enhances the rate of adsorption of the adsorbate onto the adsorbents including biosorbents (Unuabonah et al. 2007).
The process can be endothermic or exothermic. A positive value of ∆H° specifies that the adsorption process is endothermic in nature, while the opposite is realized in the case of sorption of exothermic nature. In the cases of exothermic processes, low temperatures will favor biosorption, while high temperatures will favor biosorption for the endothermic process. In most of the articles reviewed in this work, researchers focusing on studying the effect of temperature concluded that the sorption was endothermic and spontaneous with enhanced randomness (Gautam et al. 2020b). The beneficial mechanism of biosorption at high temperatures is explained by an enhanced diffusion rate at a relatively higher temperature. For the removal of Diuron, the value of the activation enthalpy (ΔH°) is <40 kJ/mol, which allows us to suggest that the uptake process follows a physisorption mechanism (de Bezerra et al. 2020). The same behavior was observed in Adebayo et al. (2019). The authors observed the increase in the randomness degree during the adsorption process, which confirmed the physisorption nature of the sorption mechanisms (Adebayo et al. 2019). A decrease in the percentage removal of Cr(IV) from 91.40 to 37.93% using Moringa stenopetala seed powder (MSSP) has been observed as temperature increased from 293 to 353 K. Similar observation has been made on adsorption capacities of Cr(VI) ion when the adsorption capacity of MSSP for Cr(VI) was decreased from 1.37 to 0.57 mg/g with increasing temperature from 293 to 353 K. This fall of the adsorbent metal uptake capacity with an increase in temperature might be due to desorption caused by an increase in the available thermal energy. The decrease in adsorption capacity with increasing temperature, therefore, indicates that this biosorption process is exothermic in nature. The negative values of ΔG° and ΔH° confirm the spontaneous and exothermic nature of the sorption of Cr(VI) ion onto both adsorbents. A positive value of ΔS° indicates the increase in the randomness of Cr(VI) ion at the solid-liquid interface of the adsorbents during the sorption process (Badessa et al. 2020). The adsorption capacity increases with increasing temperature from 30 to 50 °C (Gautam et al. 2020b). The thermodynamic study showed that the adsorptive separation of Pb(II) onto synthesized nanosorbent was spontaneous and feasible with enhanced randomness. The values of ΔS° and ΔH° are 84.75 J and 15.66 KJ mol−1; a positive value of ΔH° implicated that the adsorption of Pb(II) was endothermic in nature and for the value of the ΔG° is negative showed the spontaneity and practicability of the sorption process. Reduction in ΔG° values with the increase in temperature professed that higher temperature amplified the extent of adsorption of Pb(II). The synthesized nanomaterial based on MO performed efficiently and 94.08% removal of Pb(II) was achieved within 60 min of contact time (Gautam et al. 2020b). For As(V) removal using activated MO, the Δ𝐺° value is negative showing that this biosorption was feasible and spontaneous. While the positive Δ𝐻° values depicted the endothermic nature of the adsorption. The positive Δ𝑆° values revealed the increased randomness at the solid-solution interface (Sumathi and Alagumuthu 2014).
Hence, the biosorption mechanisms can be suggested according to the change in the magnitude of enthalpy of the adsorption (ΔH°). During the physisorption process, the values of ΔH° are generally in the range of 2.1–20.9 KJ mol–1, while the ΔH° value of the chemisorption process climbs into a range of 80–200 kJ mol–1. Several researchers confirm that the relative strength is electrostatic (6–80 kJ/mol) > hydrogen bonds (4–13 kJ/mol) > van der Waals (2–4 kJ/mol) (Scheufele et al. 2016; Módenes et al. 2017). However, the positive values of entropy of adsorption (∆S°) explain the enhanced randomness at the solid-liquid boundary. While the competitive sorption of solvent and adsorbate molecules is randomness sensitive. Logically, adsorbate molecules displace the adsorbed solvent molecules for the capturing of sorption sites exposed to the surface of the adsorbent, which is amenable for the existence of randomness in the system (Gautam et al. 2020b).
Effect of sorbent dosage on sorption by Moringa oleifera
The sorbent dosage (SD, g/L) is the most critical parameter, which can establish the capability of an adsorbent for any specified sorption of unwanted pollutant and provides an indication about the treatment cost of MO/MO-based biomaterials. The influential parameter “liquid-to-mass ratio, V/m” included in the mass balance equation of the adsorption system for calculating the sorption capacity can be measured in two ways, either at fixed volume (V) with a varied mass (m1,…., mn) or at a varied volume (V1, …..,Vn) with a fixed mass (m). It was ascertained from the available literature data on MO biosorption that changes in the value of this parameter is strongly subjective to applied concentrations of pollutants, type of pollutant, water chemistry (pH, water quality), and as well as on the conditions used for investigating the effect of this parameter. For example, the investigations on the removal of Cr(VI) using MSSP have shown that the percent removal of Cr(IV) increases from 24.85 to 90.96% with an increase in adsorbent dose from 5 to 20 g/L, while the other factors were kept constant. However, the quantity of adsorbate metal ion per unit weight of the adsorbent decreases with an increase in the adsorbent dose (Badessa et al. 2020).
To identify the mass transfer resistance parameters (e.g., external mass transfer rate, intraparticle surface diffusion, and pore diffusion) controlling the biosorption rate, we must follow the variations in the quantity of solute adsorbed onto an adsorbent as a function of time. Various kinetic models are largely exploited to analyze the determined kinetic data; most of these models are represented in the next part.
Efficient models for the modeling of biosorption equilibrium and kinetics data
Modeling of biosorption equilibrium data
The effectiveness of a biosorbent is typically approved by its ability to remove a specific adsorbent irrespective of chemical or physical interactions, batch sorption experiments at constant temperature conditions are carried out. The isotherm of the solid phase adsorbate concentration (qe) and the liquid phase equilibrium concentration (Ce) is plotted. Various adsorption isotherm models are practiced, and these models provide important information concerning the mechanisms of biosorption and tender information about the retention characteristics of a biosorbent. Additionally, these models allow explaining the distribution of the sorbate between solid and liquid phases at equilibrium conditions (Demey et al. 2018).
The famous theoretical isotherm models that describe the biosorption process are the Freundlich, Langmuir, and Sips models. The Temkin model is most of the time practiced when the temperature effect takes into account. The mathematical fit of the experimental data applying these models does not necessarily mean that all the relevant physical assumptions are verified; this can be useful for obtaining additional information on sorption mechanisms. Knowing that the Langmuir model is the most used to explain the homogeneous area, the Freundlich is the best and most reliable to explain the phenomenon of biosorption in heterogeneous surfaces, and the Sips model for heterogeneous and mixed surfaces. The results of Araújo et al. (2010a) confirm the higher heterogeneity of the MO matrix. Despite the heterogeneous surface of Moringa, the Langmuir isothermic model remains the frequently used model in MO biosorption because of the high adsorbate concentrations used. The Langmuir isotherms (L-shaped) is characterized by a slope, which increases with increasing concentration because the vacant sorption sites decrease as the biosorbent is covered. Such sorption behavior could be explained by the strong affinity of the adsorbent for the adsorbate; in addition, it is due to the availability of active sites at low concentrations, which then decreases with increasing concentration. For example, the nanoadsorbent based on MO has been explored for the effective removal of Pb(II), isotherm analysis revealed that the sorption of Pb(II) onto MO obeyed the Freundlich adsorption isotherm. The maximum adsorption capacities were found to be 49.0, 54.7, and 65.0 mg·g−1 at 30, 40, and 50 °C, respectively. The values of separation factor (RL) were found to be 1.14 × 10−3 for 30 °C, 1.34 × 10−3 for 40 °C, and 1.73 × 10−3 for 50 °C (Gautam et al. 2020b). The removal of As(V) using activated MO at pH 7.0, 140-min equilibrium time, 120 rpm, and 303 K was studied and the Qmax by using the Langmuir model was 6.23 mg/g. The fitting of the Langmuir isotherm was better relative to the Freundlich isotherm, thus indicating that the applicability of monolayer coverage of arsenic on increasing the temperature increased the arsenic adsorption rate. The equilibrium data was also well described by the Temkin equation further supporting arsenic adsorption on MO as a chemisorption process (Sumathi and Alagumuthu 2014).
Besides, to estimate the suitability degree of each model, we must look at its basic assumptions. For example, the Freundlich and/or Sips model stipulates that pollutant binding to the adsorbent surface is primarily by physical forces (i.e., electrostatic or London–van der Waals forces). The next assumption for the Temkin model is that all sites possess an equal affinity for the adsorbate (Davis et al. 2003). So, assuming that all surface and adsorption sites are equivalent and have the same affinity for a certain solute (surface of biomass is energetically homogeneous). The adsorption phenomenon is simply represented by the migration and the occupation of a surface site on a solid (adsorbent) by a pollutant (Davis et al. 2003). Each pollutant must occupy one energy site on the sorbent surface (only bind a single molecule of sorbate), and adsorbed molecules do not interact with each other in a way that influences their sorption behavior. In the biosorption process, at least one of the Langmuir hypotheses is not applicable because always the biomass behavior remains unexplained and anonymous. Generally, in the case of Moringa, we have heterogeneous sites, the most suitable model is that of Sips because we have chemical adsorption followed by physical adsorption (multilayer) or Langmuir also, can better represent experimental data.
The Langmuir binding parameter, typically represented by “b,” reflects quantitatively the “affinity” between the sorbent and the sorbate (Holan and Volesky 1994). For the Langmuir isotherm equation, the product of Langmuir maximum capacity parameter and binding parameter (qm × b) is analogous to a distribution coefficient (L g−1) and represents the initial slope of the isotherm curve (Coldebella et al. 2017; Wang et al. 2017).
Adsorption kinetics
The kinetics of biosorption is an essential knowledge necessary for the practical implementation of a biosorbent because the state of adsorption equilibrium is not accomplished instantly. It is a well-recognized reality, especially for porous biosorbents like MO. The biosorbents with rapid biosorption kinetic properties are desired due to the short contact time between adsorbing ions and biosorbents in the biosorption reactor. The identification of mass transfer resistances influencing the kinetics of biosorbent and optimization of specific biosorbent properties regarding biosorption kinetics can guide us to improve the manufacturing process of biosorbent for rapid kinetics.
The adsorption phenomena of MO can be studied from a kinetic point of view; the experimental data concerning the adsorbed quantity of the pollutant as a function of the contact time variation are important because they provide us additional information on mass transfer resistance. During biosorption, the transfer of adsorbing metal ions takes place from the fluid phase to the active sites of the biosorbents take place in four chronological phases (Worch 2012; Usman et al. 2020b, 2021) as illustrated in Fig. 10. These four chronological phases of adsorption kinetic are
-
a)
Transport of metal ion from the solution to the stagnant (boundary) layer enveloping the discrete particle of the biomaterial
-
b)
Transfer of metal ions across the boundary layer to the biosorbent’s surface. This phase of the sorption kinetics is largely known as film diffusion and represents the displacement of metal ions in the liquid phase in proximity to the solid particle.
-
c)
Transfer of metal ions to the active energy sites inside the discrete particle. This phase is overwhelmingly classified as intra-particle surface diffusion or simply surface diffusion in the micropores and macropores of particles.
-
d)
Bounding of metal ions to the unoccupied active energy sites available in the discrete particle of a biomaterial, and it is achieved by complexation or precipitation of the metal ion or even by a mixed biosorption mechanism. The adsorbing ion can diffuse from one adsorption site to another either in the free state (after desorption) in the intraparticle liquid phase (migration characterized by a diffusion coefficient Df) or in the adsorbed state, for an adsorption site to an adjacent site (surface migration). The mechanism of the adsorption process showed that the film diffusion is mostly a rate-determining step (Jabar et al. 2020).
In the available literature, MO adsorption kinetics is explained by traditional kinetics models based on the rate order of chemical reactions. The kinetic models most often used for biosorption experiments are the pseudo-first-order (PFO) model (Lagergren 1898; Barrett et al. 1951; Tien 1994; Srivastava et al. 2006) and the pseudo-second-order (PSO) model (Weber 1963; Do 1998; Ho and McKay 1998). These equations are introduced due to their relatively simple and clear expressions in the application of MO adsorption (Ho and McKay 1999; Katal et al. 2012; Zhang et al. 2013). Equations 10 and 11, respectively, relate to the nonlinear expression of the PFO and PSO models.
It should be noted that respective linear forms of Eqs. 10 and 11 are
with qt and qeq are respectively the solid phase quantities of metal ion at a specific time and at equilibrium. 𝑘1 and 𝑘2 are, respectively, the rate constants of PSO (min−1) and PSO (g mg−1 min−1). It should be noted that rate constants 𝑘1 and 𝑘2 should be considered apparent rate parameters. A kinetic study by Gautam et al. (2020b) deciphered that equilibrium adsorption for the removal of Pb(II) by MO corresponds more to the pseudo-second-order model than to the first-order model. The first-order rate constant k1 was found to be −0.0682 min−1, whereas the calculated second-order rate constant k2 was 3.75 × 10−3 g mg−1 min−1 (Gautam et al. 2020b).
For the MO and MO-based biomaterials, nonlinear expressions of the kinetic models have been applied since these biomaterials have heterogeneous surfaces (Benettayeb and Haddou 2021). Indeed, these two models were initially developed for the description of homogeneous reactions; their application to heterogeneous systems means that the intrinsic contribution of diffusion resistance is included in the apparent rate parameters (in the first case of linear modeling, it is considered that the speed is constant during all the adsorption stages, but the apparent speed is a speed made up of several speeds due to the conditions of the adsorption reaction and to the heterogeneous surface of the adsorbent and other conditions directly related to the type of adsorbent). The total adsorption rate is challenged either by the rate of diffusion of the boundary layer or by the rate of intraparticle diffusion or by the rates of the two stages.
Biosorption mechanisms and key functional groups in the MO surface
The use of Moringa as a biosorbent is of environmental and economic interest. However, various conspicuous information gaps remained as an obstacle to understanding the mechanistic pathways responsible for its water purification capabilities using biosorption (Ndibewu et al. 2011; Mnisi and Ndibewu 2017). For this reason, in this review, we have proposed a method of sorption mechanisms of Pb(II), CV, and BG ions on the source of MO and new MO-GEL materials proposed by (Benettayeb and Haddou 2021). Figure 9 gives a schematic illustration for the different stages of the transfer of adsorbate onto a porous area of biosorbent; these steps are inspired by using a work of Weber and Smith (Weber 1972).
Schematic illustration for the different stages of the transfer of an adsorbate onto a porous area of biosorbent; these steps are inspired by using a work of Weber and Smith (Weber 1972)
For Moringa, you can observe that different types of interactions can act simultaneously. Some of the physical and chemical interactions are precipitation, ion exchange, complexation, hydrogen bond, electrostatic interaction, acid-base interactions, and others. In most cases, a combination of these interactions is proposed to explain the biosorption mechanisms of MO like most biosorbents. So, some gaps motivated the research into elucidating the surface and adsorptive properties of the different parts of MO (such as seeds, husks, leaves) to appreciate its sorption mechanisms.
Many functional groups, especially the protein participate in the MO biosorption process. Each of them has a different affinity for adsorbing heavy metal/dyes, and there are several parameters to manage these preferences and affinity. Accordingly, in this part of this review, the biosorption mechanisms and the sites participating in this mechanism for the elimination of different toxic pollutants by different biomaterials have been holistically examined.
According to various work using MO, the FTIR spectrums showed the presence of hydroxyl group (–OH), carboxylic acids (–COOH), protein (–NH2), presence of; C=C, esters (–C=O), ethers (>C–O), and the ring involvement or aromatic structure of the compound can be involved in several mechanisms and methods in the biosorption process of metals and dyes like; ion exchange, chelation, physisorption, chemisorption, etc. (Abatal et al. 2021; Benettayeb and Haddou 2021).
For the MO powder, the chemisorption is the main mechanism, which is facilitated and supported by electrostatic attraction and ion-exchange mechanisms, and in some cases, the electrostatic attraction is also the most common mechanism in the biosorption. According to Haghseresht et al. (2009), the ion exchange method is usually used when porous sorbents have the function of cation exchange. Ion exchange occurs between soluble ions such as K+, Na+, Ca2+, NH4+, and metal ions. Also, according to Hegazy et al. (2021), the hydroxyl (OH) groups, C–H, C=C of alkenes, and C–O of carboxylic acids are the functional groups responsible for metal removal in Moringa seed husks.
Figure 8 represents the structural load of MO at different pH values. The electrostatic and other possible mechanisms on the surface of MO are illustrated in Figs. 10 and 11. With increasing pH, and when pH < pHpzc, the increased H+ in solution will react with the surface hydroxyl groups to form some protonated hydroxyl groups. The electrostatic attraction between a protonated hydroxyl group and M2+ (for example Pb2+) will be favorable for biosorption. The electrostatic characteristics are affected by the existence of surface chemical groups and pH solutions (Moreno-Barbosa et al. 2013). The active sites in surface groups in aqueous media can act for the capture and retention of metal species. Generally, the biosorption of Pb(II) can be influenced by the interaction mode with the solid surface (de Oliveira et al. 2019), ion-exchange mechanism, and the electrostatic characteristics between the biosorbent and the adsorbate. For example, the capacity of MO to remove heavy metals has highlighted amino acid-metal interactions responsible for the adsorption phenomenon (Subramanium et al. 2011; Nand 2012). The presence of more –OH groups on the sorbents’ surface creates more possibility of Pb–OH ion exchange (Fig. 11), and nitrogen and oxygen functional groups can provide many active adsorption sites to form strong chelation with lead ions in the aqueous solution.
Based on available literature on MO as biosorbent, Fig. 11 shows the possible mechanisms involved in the biosorption of cationic dyes (for example, CV, VB) and Pb(II). Generally, the positively charged pollutant in water is first attracted to the MO/MO-based biomaterials surface by the electrostatic force. Then, the metal ions or dyes diffuse in the entry of the pores and after inside in the pores by ionic diffusion, then they are put in contact with the various functional groups. Finally, the ions of metals or dyes are fixed with one of these groups (according to their preferences, their nature, and class) containing nitrogen –N, oxygen –O, or sulfur –S by chelation and/or ion exchange, forming a stable binding structure (metal ions according to their types and preferences, size, etc.), which is one of the possible paths of pollutants adsorbed by MO and MO-based biomaterials. View that the complexity of the mechanisms, which remains difficult to understand because it is mixed, and we find several types of adsorption and reaction at the same time (Swelam et al. 2018; Tang et al. 2018).
It is relevant to highlight that the MOS contains polyelectrolyte groups that can also contribute to the adsorption of positive metal ions and can form a bridge between the anionic polyelectrolyte and negatively charged protein functional groups on the colloidal particle surface (Steinnes 1995; Abdeen 2018).
Conclusion and prospects of MO as biosorbent
As a part of the resolution of the environmental problems related to the presence of organic (dyes) and inorganic (heavy metal ions) pollutants in wastewater, this review concludes that the seeds, husk, leaves, and bark of the MO plant can efficiently be applied for the removal of aforementioned pollutants in water, and it has substantial potential that serves as an alternative sorbent to chemically synthesized materials in water purification. This review further explores the possibility of the improvement of the MO for use in industrial wastewater treatment. Therefore, in this review, we tried to answer the question “why there is a growing interest to use MO in the field of biosorption?”, “what are the important properties of this plant?” and clarify the vision of readers on the miraculous properties of the MO.
Thanks to several pieces of research, all revised results we were able to draw the following conclusion and all of these researchers confirming that
-
1-
MO is a plant, and its growing plantation can participate in rural economic development.
-
2-
The interest in the use of MO is due to several advantages such as it is a green biosorbent available in rural areas, an environment-friendly alternative biosorbent for the remediation of some contaminated waters. Recent research works have confirmed that MO has several advantages over commonly used biosorbents. For example, powdered MOS contain cationic polyelectrolytes, which act as a natural flocculent to clarify even the most turbid water and achieve biosorption, low operating cost, production of biodegradable sludge, and lower sludge volume and pH of the water unchanged.
-
3-
The different characterization methods used by the researchers revealed the presence of different functional groups such as hydroxyl, amine, and carbonyl indicating the complex nature and justifying the biosorption capacity of MO. These functional groups have enabled the adsorption process because they offer active sites responsible for biosorption.
-
4-
The different physicochemical mechanisms responsible for the retention of heavy metals by MO are presented in this review and thanks to the heterogeneous rich surface, the mechanism of biosorption by MO is rich and includes electrostatic attraction and ion exchange.
-
5-
In order to increase the pH range and to check the precipitation phenomena, it is necessary to first carry out a pH study and a verification of the pHPZC and necessary to give information about the surface charge at different pH.
-
6-
Literature work on biosorption thermodynamics indicated that most of the sorption process was endothermic, and the negative values of ΔG° showed a spontaneous and favorable biosorption process.
-
7-
Some theoretical models are exposed in this work; the validation of the modeling of the experimental results by one or the other model does not necessarily mean that the hypotheses linked to these models are validated; the results and the interpretations also depend on the experimental conditions. In MO biosorption, generally, the chemisorption is followed by physisorption, the latter making the surface fragile with additional layers of pollutants. This type of adsorption allowed the ionic species to adhere to active sites of adsorbent and other types of physicochemical interaction. Unfortunately, despite the richness of this plant, it is humiliating by most research, and a bit of good research has been developed for biosorption using this plant. However, further studies are needed on the use of MO to remove toxic dyes and heavy metals, and researchers are in quest of novel environment-friendly techniques for the modification of MO in order to not affect its basic efficiency and to improve these properties.
In this work, we encourage researchers to find new ways of modifying the structure of different parts of MO, especially the leaves and seeds in order to improve these basic properties and increase their efficiency against toxic pollutants. We suggest the utilization and enhancement of new physical forms enhance the use of this free natural source.
More in-depth research will be desirable in the future for a promising valorization of these biosorbents, which could compete with commercial biosorbents in the treatment of wastewater, in particular, the effluents of textile industries to preserve a healthy and livable environment. In addition, a dynamic study would be necessary before a possible transition to real conditions.
In future studies, adsorption kinetics models such surface diffusion model and pore diffusion model should be employed to elucidate the mass transfer processes controlling the biosorption process. This would also us to identify the Moringa-derived biosorbents with rapid adsorption kinetics. Similarly, based on the quantification results on MO biosorption kinetics, different application-orientated water treatment strategies relying on adsorption such as fixed-bed adsorption columns and adsorption-membrane hybrid systems can be explored.
-
1.
Moringa species other than MO such as Moringa stenopetala and Moringa drouhardii should be comprehensively explored for use in wastewater treatment for heavy metal ions.
-
2.
We encourage researchers to synthesize other generations of MO either by cold gelation method (using olive oils) or hot (ionic gelation) to form beads and test them in comparative studies in batches and in dynamic mode for a future application in the treatment of wastewater (in order to optimize the parameters of operation) to pass following to real applications in the chemical industry.
Data availability
All data are mentioned in the body of the manuscript, tables, and figures.
References
Abatal M, Olguin MT, Anastopoulos I et al (2021) Comparison of heavy metals removal from aqueous solution by Moringa oleifera leaves and seeds. Coatings 11. https://doi.org/10.3390/coatings11050508
Abdeen SA (2018) Influence of using treated wastewater with moringa seeds and chitosan on wheat growth and uptake of nutrients and heavy metals
Acheampong MA, Pereira JPC, Meulepas RJW, Lens PNL (2011) Biosorption of Cu(II) onto agricultural materials from tropical regions. J Chem Technol Biotechnol 86:1184–1194. https://doi.org/10.1002/jctb.2630
Adebayo GB, Jamiu W, Okoro HK et al (2019) Kinetics, thermodynamics and isothermal modelling of liquid phase adsorption of methylene blue onto Moringa pod husk activated carbon. South African J Chem 72:263–273. https://doi.org/10.17159/0379-4350/2019/v72a34
Adeniyi AG, Ighalo JO (2019) Biosorption of pollutants by plant leaves: an empirical review. J Environ Chem Eng 7. https://doi.org/10.1016/j.jece.2019.103100
Ahmady-Asbchin S, Andrès Y, Gérente C, Le CP (2008) Biosorption of Cu(II) from aqueous solution by Fucus serratus: surface characterization and sorption mechanisms. Bioresour Technol 99:6150–6155. https://doi.org/10.1016/j.biortech.2007.12.040
Aja PM, Nwachukwu N, Ibiam UA et al (2014) Chemical constituents of Moringa oleifera leaves and seeds from Abakaliki, Nigeria. Am J Phytomedicine Clin Ther 2:310–321. https://doi.org/10.1016/j.jht.2014.02.001
Albadarin AB, Collins MN, Naushad M et al (2017) Activated lignin-chitosan extruded blends for efficient adsorption of methylene blue. Chem Eng J 307:264–272. https://doi.org/10.1016/j.cej.2016.08.089
Ali EN, Alfarra SR, Yusoff MM, Rahman ML (2015) Environmentally friendly biosorbent from Moringa oleifera leaves for water treatment. Int J Environ Sci Dev 6:165–169. https://doi.org/10.7763/ijesd.2015.v6.582
Anwar F, Latif S, Ashraf M, Gilani AH (2007) Moringa oleifera: a food plant with multiple medicinal uses. Phyther Res 21:17–25
Araújo CST, Almeida ILS, Rezende HC et al (2018) Elucidation of mechanism involved in adsorption of Pb(II) onto lobeira fruit (Solanum lycocarpum) using Langmuir, Freundlich and Temkin isotherms. Microchem J 137:348–354. https://doi.org/10.1016/j.microc.2017.11.009
Araújo CST, Alves VN, Rezende HC et al (2010a) Characterization and use of Moringa oleifera seeds as biosorbent for removing metal ions from aqueous effluents. Water Sci Technol 62:2198–2203. https://doi.org/10.2166/wst.2010.419
Araújo CST, Melo EI, Alves VN, Coelho NMM (2010b) Moringa oleifera Lam. seeds as a natural solid adsorbent for removal of AgIin aqueous solutions. J Braz Chem Soc. https://doi.org/10.1590/S0103-50532010000900019
Araujo LA, Bezerra CO, Cusioli LF et al (2018) Moringa oleifera biomass residue for the removal of pharmaceuticals from water. J Environ Chem Eng 6:7192–7199. https://doi.org/10.1016/j.jece.2018.11.016
Arora NK, Chauhan R (2021) Heavy metal toxicity and sustainable interventions for their decontamination. Environ Sustain 4:1–3. https://doi.org/10.1007/s42398-021-00164-y
Atia AA, Donia AM, Elwakeel KZ (2005a) Adsorption behaviour of non-transition metal ions on a synthetic chelating resin bearing iminoacetate functions. Sep Purif Technol 43:43–48. https://doi.org/10.1016/j.seppur.2004.09.012
Atia AA, Donia AM, Yousif AM (2005c) Comparative study of the recovery of silver(I) from aqueous solutions with different chelating resins derived from glycidyl methacrylate. J Appl Polym Sci 97:806–812. https://doi.org/10.1002/app.21751
Awual MR (2015) A novel facial composite adsorbent for enhanced copper(II) detection and removal from wastewater. Chem Eng J 266:368–375. https://doi.org/10.1016/J.CEJ.2014.12.094
Awual MR (2016a) Solid phase sensitive palladium(II) ions detection and recovery using ligand based efficient conjugate nanomaterials. Chem Eng J 300:264–272. https://doi.org/10.1016/J.CEJ.2016.04.071
Awual MR (2016b) Assessing of lead(III) capturing from contaminated wastewater using ligand doped conjugate adsorbent. Chem Eng J 289:65–73. https://doi.org/10.1016/J.CEJ.2015.12.078
Awual MR (2019a) Mesoporous composite material for efficient lead(II) detection and removal from aqueous media. J Environ Chem Eng 7:103124. https://doi.org/10.1016/J.JECE.2019.103124
Awual MR (2019b) Novel ligand functionalized composite material for efficient copper(II) capturing from wastewater sample. Compos Part B Eng 172:387–396. https://doi.org/10.1016/J.COMPOSITESB.2019.05.103
Awual MR (2019c) Efficient phosphate removal from water for controlling eutrophication using novel composite adsorbent. J Clean Prod 228:1311–1319. https://doi.org/10.1016/J.JCLEPRO.2019.04.325
Awual MR (2016c) Ring size dependent crown ether based mesoporous adsorbent for high cesium adsorption from wastewater. Chem Eng J 303:539–546. https://doi.org/10.1016/J.CEJ.2016.06.040
Awual MR, Hasan MM (2019) A ligand based innovative composite material for selective lead(II) capturing from wastewater. J Mol Liq 294:111679. https://doi.org/10.1016/J.MOLLIQ.2019.111679
Awual MR, Yaita T, Kobayashi T et al (2020) Improving cesium removal to clean-up the contaminated water using modified conjugate material. J Environ Chem Eng 8:103684. https://doi.org/10.1016/J.JECE.2020.103684
Awual MR, Yaita T, Shiwaku H (2013) Design a novel optical adsorbent for simultaneous ultra-trace cerium(III) detection, sorption and recovery. Chem Eng J 228:327–335. https://doi.org/10.1016/J.CEJ.2013.05.010
Awual MR, Yaita T, Suzuki S, Shiwaku H (2015) Ultimate selenium(IV) monitoring and removal from water using a new class of organic ligand based composite adsorbent. J Hazard Mater 291:111–119. https://doi.org/10.1016/j.jhazmat.2015.02.066
Badessa TS, Wakuma E, Yimer AM (2020) Bio-sorption for effective removal of chromium(VI) from wastewater using Moringa stenopetala seed powder (MSSP) and banana peel powder (BPP). BMC Chem 14. https://doi.org/10.1186/s13065-020-00724-z
Baptista ATA, Silva MO, Gomes RG et al (2017) Protein fractionation of seeds of Moringa oleifera lam and its application in superficial water treatment. Sep Purif Technol 180:114–124. https://doi.org/10.1016/j.seppur.2017.02.040
Barrett EP, Joyner LG, Halenda PP (1951) The determination of pore volume and area distributions in porous substances. I. Computations from Nitrogen Isotherms. J Am Chem Soc 73:373–380. https://doi.org/10.1021/ja01145a126
Benettayeb A, Guibal E, Bhatnagar A et al (2021a) Effective removal of nickel (II) and zinc (II) in mono-compound and binary systems from aqueous solutions by application of alginate-based materials. Int J Environ Anal Chem 00:1–22. https://doi.org/10.1080/03067319.2021.1887164
Benettayeb A, Guibal E, Morsli A, Kessas R (2017) Chemical modification of alginate for enhanced sorption of Cd(II), Cu(II) and Pb(II). Chem Eng J 316:704–714. https://doi.org/10.1016/j.cej.2017.01.131
Benettayeb A, Haddou B (2021) New biosorbents based on the seeds, leaves and husks powder of Moringa oleifera for the effective removal of various toxic pollutants. Int J Environ Anal Chem 00:1–26. https://doi.org/10.1080/03067319.2021.1963714
Benettayeb A, Morsli A, Elwakeel KZ, et al (2021b) Recovery of heavy metal ions using magnetic glycine - modified chitosan—application to aqueous solutions and tailing leachate. 1–22
Benettayeb A, Morsli A, Guibal E, Kessas R (2021c) New derivatives of urea-grafted alginate for improving the sorption of mercury ions in aqueous solutions new derivatives of urea-grafted alginate for improving the sorption of mercury ions in aqueous solutions
de Bezerra CO, Cusioli LF, Quesada HB et al (2020) Assessment of the use of Moringa oleifera seed husks for removal of pesticide diuron from contaminated water. Environ Technol (United Kingdom) 41:191–201. https://doi.org/10.1080/09593330.2018.1493148
Bhatti HN, Mumtaz B, Hanif MA, Nadeem R (2007) Removal of Zn(II) ions from aqueous solution using Moringa oleifera Lam. (horseradish tree) biomass. Process Biochem 42:547–553. https://doi.org/10.1016/j.procbio.2006.10.009
Broin M (2012) Composition nutritionnelle des feuilles de Moringa oleifera. Free Radic Biol Med 52:1–5
Boudrahem F, F. Aissani-Benissad AS (2011) Pb (II) and Cd (II) removal from aqueous solutions using activated carbon developed from coffee residue activated with phosphoric acid and zinc chloride. J Chem Eng Data 56:1945
Bruneton J (1999) Pharmacognosie, phytochimie, plantes médicinales. Lavoisier Technique & Documentation, Paris
Burakov AE, Galunin EV, Burakova IV et al (2018) Adsorption of heavy metals on conventional and nanostructured materials for wastewater treatment purposes: a review. Ecotoxicol Environ Saf 148:702–712
Cai YH, Galili N, Gelman Y et al (2021) Evaluating the impact of pretreatment processes on fouling of reverse osmosis membrane by secondary wastewater. J Memb Sci 623. https://doi.org/10.1016/j.memsci.2021.119054
Çelekli A, Al-Nuaimi AI, Bozkurt H (2019) Adsorption kinetic and isotherms of Reactive Red 120 on Moringa oleifera seed as an eco-friendly process. J Mol Struct 1195:168–178. https://doi.org/10.1016/j.molstruc.2019.05.106
Coldebella PF, Fagundes-Klen MR, Nishi L et al (2017) Potential effect of chemical and thermal treatment on the kinetics, equilibrium, and thermodynamic studies for atrazine biosorption by the Moringa oleifera pods. Can J Chem Eng 95:961–973. https://doi.org/10.1002/cjce.22756
Cusioli LF, de Bezerra CO, Quesada HB et al (2019) Modified Moringa oleifera Lam. Seed husks as low-cost biosorbent for atrazine removal. Environ Technol (United Kingdom). https://doi.org/10.1080/09593330.2019.1653381
Davis TA, Volesky B, Mucci A (2003) A review of the biochemistry of heavy metal biosorption by brown algae. Water Res 37:4311–4330
de Oliveira TF, de Moraes Pinto LA, Marinozi Vicentini JC et al (2019) Analysis of the influence of natural adsorbent functionalization (Moringa oleifera) for Pb(II) removal from contaminated water. Environ Prog Sustain Energy 1–10. https://doi.org/10.1002/ep.13318
De Saint Sauveur et Broin 2006 MN& BK Teneur en composés phénoliques et activité antioxydante d’extrait au méthanol des feuilles de MORINGA OLEIFERA,Mémoire de fin de cycle, Université Abderrahmane MIRA de Bejaia,2017
Deblonde GJP, Lohrey TD, An DD, Abergel RJ (2018) Toxic heavy metal-Pb, Cd, Sn-complexation by the octadentate hydroxypyridinonate ligand archetype 3,4,3-LI(1,2-HOPO). New J Chem 42:7649–7658. https://doi.org/10.1039/c7nj04559j
Demey H, Lapo B, Ruiz M et al (2018) Neodymium recovery by chitosan/iron(III) hydroxide [ChiFer(III)] sorbent material: batch and column systems. Polymers (Basel) 10:1–21. https://doi.org/10.3390/polym10020204
Do DD (1998) Adsorption Analysis: Equilibria and Kinetics. Imp Coll Press, London
Donia AM, Atia AA, Abouzayed FI (2012) Preparation and characterization of nano-magnetic cellulose with fast kinetic properties towards the adsorption of some metal ions. Chem Eng J 191:22–30. https://doi.org/10.1016/j.cej.2011.08.034
Elwakeel KZ, Atia AA, Guibal E (2014) Fast removal of uranium from aqueous solutions using tetraethylenepentamine modified magnetic chitosan resin. Bioresour Technol 160:107–114. https://doi.org/10.1016/j.biortech.2014.01.037
Eun WS, Rowell RM (2005) Cadmium ion sorption onto lignocellulosic biosorbent modified by sulfonation: the origin of sorption capacity improvement. Chemosphere 60:1054–1061. https://doi.org/10.1016/j.chemosphere.2005.01.017
Foidl N, Makkar HPS, Becker K (2001) Potentiel de Moringa oleifera en agriculture et dans l’industrie. Actes du séminaire sur Moringa oleifera du, 29. Dar es Salaam, Tanzanie
Fomina M, Gadd GM (2014) Biosorption: current perspectives on concept, definition and application. Bioresour Technol. https://doi.org/10.1016/j.biortech.2013.12.102
Gadd GM (2009) Biosorption: critical review of scientific rationale, environmental importance and significance for pollution treatment. J Chem Technol Biotechnol
Ganguly S (2013) Indian ayurvedic and traditional medicinal implications of indigenously available plants, herbs and fruits: a review. Int. J. Res. Ayurveda Pharm
Gautam AK, Markandeya SNB et al (2020a) Lead removal efficiency of various natural adsorbents (Moringa oleifera, Prosopis juliflora, peanut shell) from textile wastewater. SN Appl Sci 2:1–11. https://doi.org/10.1007/s42452-020-2065-0
Gautam PK, Shivalkar S, Banerjee S (2020b) Synthesis of M. oleifera leaf extract capped magnetic nanoparticles for effective lead [Pb (II)] removal from solution: kinetics, isotherm and reusability study. J Mol Liq 305. https://doi.org/10.1016/j.molliq.2020.112811
Gopalakannan V, Viswanathan N (2015) Development of nano-hydroxyapatite embedded gelatin biocomposite for effective chromium(VI) removal. Ind Eng Chem Res. https://doi.org/10.1021/acs.iecr.5b01224
Gopalakrishnan L, Doriya K, Kumar DS (2016) Moringa oleifera: a review on nutritive importance and its medicinal application. Food Sci Hum Wellness 5:49–56
Goyal B, Agrawal B, Goyal R, Mehta A (2007) Phyto-pharmacology of Moringa oleifera Lam . ó An overview. Nat Prod Radiance. https://doi.org/10.1007/s00421-007-0443-6
Haghseresht F, Wang S, Do DD (2009) A novel lanthanum-modified bentonite, Phoslock, for phosphate removal from wastewaters. Appl Clay Sci 46:369–375. https://doi.org/10.1016/j.clay.2009.09.009
Hamza MF, Wei Y, Benettayeb A et al (2020) Efficient removal of uranium, cadmium and mercury from aqueous solutions using grafted hydrazide-micro-magnetite chitosan derivative. J Mater Sci 55:4193–4212. https://doi.org/10.1007/s10853-019-04235-8
Hasan MM, Shenashen MA, Hasan MN et al (2021a) Natural biodegradable polymeric bioadsorbents for efficient cationic dye encapsulation from wastewater. J Mol Liq 323:114587. https://doi.org/10.1016/J.MOLLIQ.2020.114587
Hasan MN, Shenashen MA, Hasan MM et al (2021b) Assessing of cesium removal from wastewater using functionalized wood cellulosic adsorbent. Chemosphere 270:128668. https://doi.org/10.1016/J.CHEMOSPHERE.2020.128668
Hegazy I, Ali MEA, Zaghlool EH, Elsheikh R (2021) Heavy metals adsorption from contaminated water using moringa seeds/olive pomace byproducts. Appl Water Sci 11:1–14. https://doi.org/10.1007/s13201-021-01421-5
Ho YS, McKay G (1998) Sorption of dye from aqueous solution by peat. Chem Eng J 70:115–124. https://doi.org/10.1016/S1385-8947(98)00076-X
Ho YS, McKay G (1999) Pseudo-second order model for sorption processes. Process Biochem 34:451–465. https://doi.org/10.1016/S0032-9592(98)00112-5
Holan ZR, Volesky B (1994) Biosorption of lead and nickel by biomass of marine algae. Biotechnol Bioeng 43:1001–1009. https://doi.org/10.1002/bit.260431102
Imran M, Anwar K, Akram M et al (2019) Biosorption of Pb(II) from contaminated water onto Moringa oleifera biomass: kinetics and equilibrium studies. Int J Phytoremediation 21:777–789. https://doi.org/10.1080/15226514.2019.1566880
Islam A, Teo SH, Awual MR, Taufiq-Yap YH (2019) Improving the hydrogen production from water over MgO promoted Ni–Si/CNTs photocatalyst. J Clean Prod 238:117887. https://doi.org/10.1016/J.JCLEPRO.2019.117887
Islam A, Teo SH, Taufiq-Yap YH et al (2021) Step towards the sustainable toxic dyes removal and recycling from aqueous solution- a comprehensive review. Resour Conserv Recycl 175:105849. https://doi.org/10.1016/J.RESCONREC.2021.105849
J. H (1998) Phytochemical methods: a guide to modern techniques of plant analysis. Edition.Chapman & Hall Pub. London, UK, pp 235–242
Jabar JM, Odusote YA, Alabi KA, Ahmed IB (2020) Kinetics and mechanisms of congo-red dye removal from aqueous solution using activated Moringa oleifera seed coat as adsorbent. Appl Water Sci 10:1–11. https://doi.org/10.1007/s13201-020-01221-3
Kadirvelu K, C. Faur-Brasquet PLC (2000) Removal of Cu(II), Pb(II), and Ni(II) by adsorption onto activated carbon cloths. Langmuir 16:8404–8409
Katal R, Hasani E, Farnam M et al (2012) Charcoal ash as an adsorbent for Ni(II) adsorption and tts application for wastewater treatment. J Chem Eng Data 57:374–383. https://doi.org/10.1021/je200953h
Kebede TG, Mengistie AA, Dube S et al (2018) Study on adsorption of some common metal ions present in industrial effluents by Moringa stenopetala seed powder. J Environ Chem Eng 6:1378–1389. https://doi.org/10.1016/j.jece.2018.01.012
Khulbe KC, Matsuura T (2018) Removal of heavy metals and pollutants by membrane adsorption techniques. Appl Water Sci 8. https://doi.org/10.1007/s13201-018-0661-6
Kooltheat N et al. (2014) An ethyl acetate fraction of Moringa oleifera Lam. inhibits human macrophage cytokine production induced by cigarette smoke. Nutrients 6(2):697–710
Kubra KT, Salman MS, Hasan MN et al (2021) Sustainable detection and capturing of cerium(III) using ligand embedded solid-state conjugate adsorbent. J Mol Liq 338:116667. https://doi.org/10.1016/J.MOLLIQ.2021.116667
Lagergren SK (1898) About the theory of so-called adsorption of soluble substances. Sven Vetenskapsakad Handingarl 24:1–39
Lin YF, Chen HW, Chien PS et al (2011) Application of bifunctional magnetic adsorbent to adsorb metal cations and anionic dyes in aqueous solution. J Hazard Mater. https://doi.org/10.1016/j.jhazmat.2010.10.022
de Lopes TSA, Heßler R, Bohner C et al (2020) Pesticides removal from industrial wastewater by a membrane bioreactor and post-treatment with either activated carbon, reverse osmosis or ozonation. J Environ Chem Eng 8. https://doi.org/10.1016/j.jece.2020.104538
Lopez-Ramon MV, Stoeckli F, Moreno-Castilla C, Carrasco-Marin F (1999) On the characterization of acidic and basic surface sites on carbons by various techniques. Carbon N Y 37:1215–1221. https://doi.org/10.1016/S0008-6223(98)00317-0
Madi OP, Bourou S, Woin N (2012) Utilisations et importances socioéconomiques du Moringa oleifera Lam. en zone de savanes d’Afrique Centrale. Cas de la ville de Maroua au Nord-Cameroun. J Appl Biosci 60:4421–4432
Mahmood KT, Mugal T, Haq IU (2010) Moringa oleifera: a natural gift-a review. J Pharm Sci Res 2(11):775
Mansaly S (2001) Récupération nutritionnelle et impact de consommation de la poudre de Moringa oleifera dans la consultation primaire et curative. Clinique Santiaba à Ziguinchor, Sénégal, 2p, disponible sur http://www. moringanews. org. Consulté le, 12
Marques TL, Alves VN, Coelho LM, Coelho NMM (2012) Removal of Ni(II) from aqueous solution using Moringa oleifera seeds as a bioadsorbent. Water Sci Technol 65:1435–1440. https://doi.org/10.2166/wst.2012.026
Mataka LM, Henry EMT, Masamba WRL, Sajidu SM (2006) Lead remediation of contaminated water using Moringa stenopetala and Moringa oleifera seed powder. Int J Environ Sci Technol 3:131–139. https://doi.org/10.1007/BF03325916
Mateus GAP, Paludo MP, Dos Santos TRT et al (2018) Obtaining drinking water using a magnetic coagulant composed of magnetite nanoparticles functionalized with Moringa oleifera seed extract. J Environ Chem Eng 6:4084–4092. https://doi.org/10.1016/j.jece.2018.05.050
Meireles D, Gomes J, Lopes L et al (2020) A review of properties, nutritional and pharmaceutical applications of Moringa oleifera: integrative approach on conventional and traditional Asian medicine. Adv Tradit Med 20:495–515
Millogo-Kone H, Guissou I, Nacoulma O, Traore A (2011) Comparative study of leaf and stem bark extracts of Parkia biglobosa against enterobacteria. African J Tradit Complement Altern Med. https://doi.org/10.4314/ajtcam.v5i3.31279
Mnisi RL, Ndibewu PP (2017) Surface and adsorptive properties of Moringa oleifera bark for removal of V(V) from aqueous solutions. Environ Monit Assess 189. https://doi.org/10.1007/s10661-017-6329-0
Módenes AN, de Oliveira AP, Espinoza-Quiñones FR et al (2017) Study of the involved sorption mechanisms of Cr(VI) and Cr(III) species onto dried Salvinia auriculata biomass. Chemosphere 172:373–383. https://doi.org/10.1016/j.chemosphere.2017.01.038
Moreno-Barbosa JJ, López-Velandia C, Maldonado ADP, et al (2013) Removal of lead(II) and zinc(II) ions from aqueous solutions by adsorption onto activated carbon synthesized from watermelon shell and walnut shell. In: Adsorption. pp 675–685
Mutheeswaran S, Pandikumar P, Chellappandian M, Ignacimuthu S (2011) Documentation and quantitative analysis of the local knowledge on medicinal plants among traditional Siddha healers in Virudhunagar district of Tamil Nadu, India. J Ethnopharmacol. https://doi.org/10.1016/j.jep.2011.06.003
Nand V (2012) Water purification using Moringa oleifera and other locally available seeds in Fiji for heavy metal removal. Int J Appl Sci Technol Vol 2:125–129
Naushad M (2014) Surfactant assisted nano-composite cation exchanger: development, characterization and applications for the removal of toxic Pb2+ from aqueous medium. Chem Eng J 235:100–108. https://doi.org/10.1016/j.cej.2013.09.013
Ndibewu PP, Mnisi RL, Mokgalaka SN, Mccrindle RI (2011) Heavy metal removal in aqueous systems using Moringa oleifera: a review. J Mater Sci Eng B 1:843–853
Ngabura M, Hussain SA, Ghani WAWA et al (2018) Utilization of renewable durian peels for biosorption of zinc from wastewater. J Environ Chem Eng 6:2528–2539. https://doi.org/10.1016/j.jece.2018.03.052
Ngineering CIE, Niversity COU, Ta O, Tate OGUNS (2019) Preliminary inverstigation on the use of moringa oleifera for the purification of lead polluted wastewater 38(1):253–257
Nieboer E, Richardson DHS (1980) The replacement of the nondescript term “heavy metals” by a biologically and chemically significant classification of metal ions. Environ Pollution Ser B, Chem Phys 1:3–26. https://doi.org/10.1016/0143-148X(80)90017-8
Obuseng V, Nareetsile F, Kwaambwa HM (2012) A study of the removal of heavy metals from aqueous solutions by Moringa oleifera seeds and amine-based ligand 1,4-bis[N,N-bis(2-picoyl)amino]butane. Anal Chim Acta 730:87–92. https://doi.org/10.1016/j.aca.2012.01.054
Okoya AA, Olaiya OO, Akinyele AB (2020) Ochor NO (2020) Efficacy of Moringa oleifera seed husk as adsorptive agent for trihalomethanes from a water treatment plant in southwestern. Nigeria. J Chem. https://doi.org/10.1155/2020/3450954
Pal P, Benettayeb A, Pal A (2019) Environmentally safe biosorbents for crystal violet removal from wastewater. Crystal Violet: Production, Applications and Precautions. Nova science publishers, Hauppauge
Pearson RG (1990) Hard and soft acids and bases-the evolution of a chemical concept. Coord Chem Rev 100:403–425. https://doi.org/10.1016/0010-8545(90)85016-L
Peng H, Guo J (2020) Removal of chromium from wastewater by membrane filtration, chemical precipitation, ion exchange, adsorption electrocoagulation, electrochemical reduction, electrodialysis, electrodeionization, photocatalysis and nanotechnology: a review. Environ Chem Lett. https://doi.org/10.1007/s10311-020-01058-x
Price PML (2007) LE MORINGA
Raj KR, Kardam A, Arora JK et al (2013) Adsorption behavior of dyes from aqueous solution using agricultural waste: modeling approach. Clean Technol Environ Policy 15:73–80. https://doi.org/10.1007/s10098-012-0480-7
Reddy DHK, Harinath Y, Seshaiah K, Reddy AVR (2010a) Biosorption of Pb(II) from aqueous solutions using chemically modified Moringa oleifera tree leaves. Chem Eng J 162:626–634. https://doi.org/10.1016/j.cej.2010.06.010
Reddy DHK, Ramana DKV, Seshaiah K, Reddy AVR (2011) Biosorption of Ni(II) from aqueous phase by Moringa oleifera bark, a low cost biosorbent. Desalination 268:150–157. https://doi.org/10.1016/j.desal.2010.10.011
Reddy DHK, Seshaiah K, Reddy AVR et al (2010b) Biosorption of Pb2+ from aqueous solutions by Moringa oleifera bark: equilibrium and kinetic studies. J Hazard Mater 174:831–838. https://doi.org/10.1016/j.jhazmat.2009.09.128
Reddy DHK, Seshaiah K, Reddy AVR, Lee SM (2012) Optimization of Cd(II), Cu(II) and Ni(II) biosorption by chemically modified Moringa oleifera leaves powder. Carbohydr Polym 88:1077–1086. https://doi.org/10.1016/j.carbpol.2012.01.073
Saa RW, Fombang EN, Ndjantou EB, Njintang NY (2019) Treatments and uses of Moringa oleifera seeds in human nutrition: a review. Food Sci Nutr 7:1911–1919. https://doi.org/10.1002/fsn3.1057
Sahebjamee N, Soltanieh M, Mousavi SM, Heydarinasab A (2019) Removal of Cu 2+ , Cd 2+ and Ni 2+ ions from aqueous solution using a novel chitosan/polyvinyl alcohol adsorptive membrane. Carbohydr Polym 210:264–273. https://doi.org/10.1016/j.carbpol.2019.01.074
Sajidu S, Henry E, Kwamdera G, Mataka L (2005) Removal of lead, iron and cadmium ions by means of polyelectrolytes of the Moringa oleifera whole seed kernel. WIT Trans Ecol Environ 80
Samaei SM, Gato-Trinidad S, Altaee A (2020) Performance evaluation of reverse osmosis process in the post-treatment of mining wastewaters: case study of Costerfield mining operations, Victoria, Australia. J Water Process Eng 34. https://doi.org/10.1016/j.jwpe.2019.101116
Scheufele FB, Módenes AN, Borba CE et al (2016) Monolayer-multilayer adsorption phenomenological model: kinetics, equilibrium and thermodynamics. Chem Eng J 284:1328–1341. https://doi.org/10.1016/j.cej.2015.09.085
Soliman NK, Moustafa AF, Aboud AA, Halim KSA (2019) Effective utilization of Moringa seeds waste as a new green environmental adsorbent for removal of industrial toxic dyes. J Mater Res Technol 8:1798–1808. https://doi.org/10.1016/j.jmrt.2018.12.010
Son DJ, Kim WY, Jung BR, et al (2020) Pilot-scale anoxic/aerobic biofilter system combined with chemical precipitation for tertiary treatment of wastewater. J Water Process Eng 35:. https://doi.org/10.1016/j.jwpe.2020.101224
Šoštarić TD, Petrović MS, Pastor FT et al (2018) Study of heavy metals biosorption on native and alkali-treated apricot shells and its application in wastewater treatment. J Mol Liq 259:340–349. https://doi.org/10.1016/j.molliq.2018.03.055
Srivastava M, Ma LQ, Santos JAG (2006) Three new arsenic hyperaccumulating ferns. Sci Total Environ 364:24–31. https://doi.org/10.1016/j.scitotenv.2005.11.002
Steinnes PB and E (1995) Trace chemistry processes, in Steinnes, E. and Salbu, B. Trace Elements in Natural Waters. CRC Press: Boca Raton, pp 21–40
Subramanium S, Nand V, Maata M, Koshy K (2011) Moringa oleifera and other local seeds in water purification in developing countries. Res J Chem Environ 15:135–138
Sumathi T, Alagumuthu G (2014) Adsorption studies for arsenic removal using activated Moringa oleifera. Int J Chem Eng. https://doi.org/10.1155/2014/430417
Swelam AA, Sherif SS, Ibrahim A (2018) The adsorption kinetics and modeling for Pb(II) removal from synthetic and real wastewater by moringa oleifera seeds. Al-Azhar Bull Sci 29(2-A):105–124. https://doi.org/10.21608/absb.2018.33773
Taiwo AS, Adenike K, Aderonke O (2020) Efficacy of a natural coagulant protein from Moringa oleifera (Lam) seeds in treatment of Opa reservoir water, Ile-Ife, Nigeria. Heliyon 6:. https://doi.org/10.1016/j.heliyon.2020.e03335
Tang N, Niu CG, Li XT et al (2018) Efficient removal of Cd2+ and Pb2+ from aqueous solution with amino- and thiol-functionalized activated carbon: isotherm and kinetics modeling. Sci Total Environ 635:1331–1344. https://doi.org/10.1016/j.scitotenv.2018.04.236
Teo SH, Ng CH, Islam A et al (2022) Sustainable toxic dyes removal with advanced materials for clean water production: a comprehensive review. J Clean Prod 332:130039. https://doi.org/10.1016/J.JCLEPRO.2021.130039
Tien C (1994) Adsorption calculations and modeling. Butterworth-Heinemann, Newton
Trivunac K, Stevanovic S (2006) Removal of heavy metal ions from water by complexation-assisted ultrafiltration. Chemosphere 64:486–491. https://doi.org/10.1016/j.chemosphere.2005.11.073
Unuabonah EI, Adebowale KO, Olu-Owolabi BI (2007) Kinetic and thermodynamic studies of the adsorption of lead (II) ions onto phosphate-modified kaolinite clay. J Hazard Mater 144:386–395. https://doi.org/10.1016/j.jhazmat.2006.10.046
Usman M, Belkasmi AI, Kastoyiannis IA, Ernst M (2021) Pre-deposited dynamic membrane adsorber formed of microscale conventional iron oxide-based adsorbents to remove arsenic from water: application study and mathematical modeling. J Chem Technol Biotechnol 96:1504–1514. https://doi.org/10.1002/jctb.6728
Usman M, Katsoyiannis I, Mitrakas M, et al (2018a) Performance evaluation of small sized powdered ferric hydroxide as arsenic adsorbent. Water (Switzerland) 10:. https://doi.org/10.3390/w10070957
Usman M, Katsoyiannis I, Rodrigues JH, Ernst M (2020a) Arsenate removal from drinking water using by-products from conventional iron oxyhydroxides production as adsorbents coupled with submerged microfiltration unit. Environ Sci Pollut Res. https://doi.org/10.1007/s11356-020-08327-w
Usman M, Waseem M, Mani N, Andiego G (2018b) Optimization of soil aquifer treatment by chemical oxidation with hydrogen peroxide addition. Pollution 4:369–379
Usman M, Zarebanadkouki M, Waseem M, et al (2020b) Mathematical modeling of arsenic(V) adsorption onto iron oxyhydroxides in an adsorption-submerged membrane hybrid system. J Hazard Mater 400. https://doi.org/10.1016/j.jhazmat.2020.123221
Vega Andrade P, Palanca CF, de Oliveira MAC, et al (2021) Use of Moringa oleifera seed as a natural coagulant in domestic wastewater tertiary treatment: physicochemical, cytotoxicity and bacterial load evaluation. J Water Process Eng 40. https://doi.org/10.1016/j.jwpe.2020.101859
Verma RK, Kumar R, Sethi M (2020) Use of distinct parts of Moringa oleifera in domestic wastewater treatment (an analogous study). In: ICRITO 2020 - IEEE 8th International Conference on Reliability, Infocom Technologies and Optimization (Trends and Future Directions). pp 463–467
Vieira AMS, Vieira MF, Silva GF et al (2010) Use of Moringa oleifera seed as a natural adsorbent for wastewater treatment. Water Air Soil Pollut 206:273–281. https://doi.org/10.1007/s11270-009-0104-y
Villaseñor-Basulto DL, Astudillo-Sánchez PD, del Real-Olvera J, Bandala ER (2018) Wastewater treatment using Moringa oleifera Lam seeds: a review. J Water Process Eng 23:151–164. https://doi.org/10.1016/j.jwpe.2018.03.017
Wang S, Hamza MF, Vincent T et al (2017) Praseodymium sorption on Laminaria digitata algal beads and foams. J Colloid Interface Sci 504:780–789. https://doi.org/10.1016/j.jcis.2017.06.028
Weber J (1972) Adsorption in physicochemical processes for water quality control. In: Metcalf RL, Pitts JN (eds) Wiley interscience, Hoboken, pp 199–259
Weber W (1963) Kinetics of adsorption on carbon from solution. J Sanit Eng Div 89:31–60
William JA, Kwame OB, Baatuuwie NB (2015) Initial growth response of Moringa oleifera seedlings to different soil amendments. African J Agric Res. https://doi.org/10.5897/ajar11.2306
Worch E (2012) Adsorption technology in water treatment. de Gruyter
Xu Z, Gu S, Rana D, et al (2021) Chemical precipitation enabled UF and MF filtration for lead removal. J Water Process Eng 41. https://doi.org/10.1016/j.jwpe.2021.101987
Zhang S, Xu F, Wang Y et al (2013) Silica modified calcium alginate-xanthan gum hybrid bead composites for the removal and recovery of Pb(II) from aqueous solution. Chem Eng J 234:33–42. https://doi.org/10.1016/j.cej.2013.08.102
Zhang Y, Duan X (2020) Chemical precipitation of heavy metals from wastewater by using the synthetical magnesium hydroxy carbonate. Water Sci Technol 81:1130–1136. https://doi.org/10.2166/wst.2020.208
Acknowledgements
The idea was born when the students “Coffee Calvin Tinashe and Traore Adam” brought this miraculous plant back from Mali. These students did their work in the “Laboratoire de Génie Chimique et de catalyse hétérogène” at university USTO-MB, Algeria; this laboratory is under construction although he was born in 1986 by Pr KESSAS Rachid. We thank them for the innovative idea that brings us to write this review article. We propose to the Algerian Ministry of Higher Education to make special sites of plantation of these trees in order to widen these axes of research.
Funding
Open Access funding enabled and organized by Projekt DEAL. Open access funding was enabled by project “DEAL.”
Author information
Authors and Affiliations
Contributions
Asmaa Benettayeb: conceptualization, literature search, literature analysis, formal analysis, and writing the original article. Muhammad Usman: literature search, formal analysis, writing the original article, review, and editing. Coffee Calvin Tinashe and Traore Adam: conceptualization. Boumediene Haddou: review and editing.
Corresponding authors
Ethics declarations
Ethics approval
Not applicable.
Consent to participate
Not applicable.
Consent for publication
Not applicable.
Competing interests
The authors declare no competing interests.
Additional information
Responsible Editor: Tito Roberto Cadaval Jr
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Benettayeb, A., Usman, M., Tinashe, C.C. et al. A critical review with emphasis on recent pieces of evidence of Moringa oleifera biosorption in water and wastewater treatment. Environ Sci Pollut Res 29, 48185–48209 (2022). https://doi.org/10.1007/s11356-022-19938-w
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11356-022-19938-w