Abstract
We report here the impact of different alloying elements in steels on friction and wear behavior by performing ball-on-flat lubricated reciprocating tribotesting experiments on 52100 ball on steel flats with different compositions (52100, 1045, A2, D2, M2, and a specialty Cu-alloyed steel) heat-treated to give similar hardness and microstructure, with polyalphaolefin (PAO-4) as the lubricant. There are small variations of coefficient of friction among these alloys. The major observation is that steels containing high concentrations (≥ 10 wt%) of Cr, Mo, and V gave rise to markedly reduced wear compared with 52100 or plain carbon steels. D2 steel, which contains 11.5 wt% Cr as the major alloying element was the most wear-resistant. The wear resistance is strongly correlated with the efficiency of formation of carbon-containing oligomeric films at specimen surfaces as determined by Raman spectroscopy. This correlation holds for steels heat-treated to have higher hardness and with n-dodecane, a much less viscous lubricant compared with PAO-4. Given the strong affinity of chromium to oxygen, chromium should exist as Cr2O3 at the steel surfaces during testing. We have performed molecular dynamics simulation on Cr2O3 and demonstrated its ability to catalyze the formation of carbon-containing oligomeric films from hydrocarbon molecules, consistent with its known catalytic activity in other hydrocarbon reactions. We believe that chromium-containing alloys, such as D2, and coatings, such as CrN, derive their wear resistance in part from the efficient in situ formation of wear-protective carbon tribofilms at contacting asperities.
Similar content being viewed by others
Data Availability
Data that supports the findings of this study are available from the corresponding author upon reasonable request.
Notes
It is known from the metallurgy literature that adding copper to steel can cause embrittlement due to the formation of liquid copper during processing and its migration to grain boundaries. The remedy is to add roughly an equal amount of nickel to hold the copper within the solid solution as the steel cools from the melt.
Assume the sample to be a semi-infinite solid with thermal conductivity K, illuminated by a laser beam with power P over a rectangular cross-section a a. The maximum temperature rise max at the center of the beam is equal to\({\theta }_{max}\approx 0.56\frac{P}{Ka}\). At a laser power P = 1.25 mW, laser spot width a = 1.0, and thermal conductivity of D2 steel K = 20 W/m–K, \({\theta }_{max}\approx 35 K\)
The heat treatment procedure for 52,100 steel is to conduct the solution treatment at 870 C for one hour and then quench in oil. The resulting Vickers hardness is 76256, based on a data set of 10 indents. The heat treatment procedure for D2 steel is to conduct the solution treatment at 1010 C for 15 min and then quench in oil, followed by tempering at 177 C for 15 min. The resulting Vickers hardness is 81733, based on a data set of 10 indents.
References
Tysoe, W.: On stress-induced tribochemical reaction rates. Tribol. Lett. 65, 1–16 (2017)
Cheng, U.C., Stair, P.C.: In situ study of multialkylated cyclopentane and perfluoropolyalkyl ether chemistry in concentrated contacts using ultraviolet Raman spectroscopy. Tribol. Lett. 4, 163–170 (1998). https://doi.org/10.1023/A:1019147020100
Cheong, C.U.A., Stair, P.C.: In situ studies of the lubricant chemistry and frictional properties of perfluoropolyalkyl ethers at a sliding contact. Tribol. Lett. 10, 117–126 (2001). https://doi.org/10.1023/A:1009094800437
Yeon, J., He, X., Martini, A., Kim, S.H.: Mechanochemistry at solid surfaces: polymerization of adsorbed molecules by mechanical shear at tribological interfaces. ACS Appl. Mater. Interfaces 9, 3142–3148 (2017)
Bhuiyan, F.H., Kim, S.H., Martini, A.: Reactive molecular dynamics simulations of thermal and shear-driven oligomerization. Appl. Surf. Sci. 591, 153209 (2022)
Hermance, H.W., Egan, T.F.: Organic deposits on precious metal contacts. Bell Syst. Tech. J. 37, 739–776 (1958)
Liao, Y., Pourzal, R., Wimmer, M.A., Jacobs, J.J., Fischer, A., Marks, L.D.: Graphitic tribological layers in metal-on-metal hip replacements. Science (80-) 334, 1687–1690 (2011). https://doi.org/10.1126/science.1213902
Erdemir, A., Ramirez, G., Eryilmaz, O.L., Narayanan, B., Liao, Y., Kamath, G., Sankaranarayanan, S.K.R.S.: Carbon-based tribofilms from lubricating oils. Nature 536, 67–71 (2016). https://doi.org/10.1038/nature18948
Argibay, N., Babuska, T.F., Curry, J.F., Dugger, M.T., Lu, P., Adams, D.P., Nation, B.L., Doyle, B.L., Pham, M., Pimentel, A., et al.: In-situ tribochemical formation of self-lubricating diamond-like carbon films. Carbon N. Y. 138, 61–68 (2018)
Pagkalis, K., Spikes, H., Jelita Rydel, J., Ingram, M., Kadiric, A.: The influence of steel composition on the formation and effectiveness of anti-wear films in tribological contacts. Tribol. Lett. 69, 75 (2021). https://doi.org/10.1007/s11249-021-01438-6
McDaniel, M.P.: Chapter 3 - A Review of the Phillips Supported Chromium Catalyst and Its Commercial Use for Ethylene Polymerization, pp. 123–606. Academic Press, Cambridge (2010)
Hakuli, A., Harlin, M.E., Backman, L.B., Krause, A.O.I.: Dehydrogenation of i-butane on CrOx/SiO2 catalysts. J. Catal. 184, 349–356 (1999)
Zhang, F., Wu, R., Yue, Y., Yang, W., Gu, S., Miao, C., Hua, W., Gao, Z.: Chromium oxide supported on ZSM-5 as a novel efficient catalyst for dehydrogenation of propane with CO2. Microporous Mesoporous Mater. 145, 194–199 (2011)
Mentasty, L.R., Gorriz, O.F., Cadus, L.E.: Chromium oxide supported on different Al2O3 supports: catalytic propane dehydrogenation. Ind. Eng. Chem. Res. 38, 396–404 (1999). https://doi.org/10.1021/ie9802562
Takehira, K., Oishi, Y., Shishido, T., Kawabata, T., Takaki, K., Zhang, Q., Wang, Y.: CO2 dehydrogenation of propane over Cr-MCM-41 catalyst. In: Park, S.E., Chang, J.S., Lee, K.W. (eds.) Carbon Dioxide Utilization for Global Sustainability, pp. 323–328. Elsevier, Amsterdam (2004)
Fine, M.E., Vaynman, S., Isheim, D., Chung, Y.-W., Bhat, S.P., Hahin, C.H.: A new paradigm for designing high-fracture-energy steels. Metall. Mater. Trans. A 41, 3318–3325 (2010). https://doi.org/10.1007/s11661-010-0485-y
Kapoor, M., Isheim, D., Ghosh, G., Vaynman, S., Fine, M.E., Chung, Y.-W.: Aging characteristics and mechanical properties of 1600MPa body-centered cubic Cu and B2-NiAl precipitation-strengthened ferritic steel. Acta Mater. 73, 56–74 (2014)
Kapoor, M., Isheim, D., Vaynman, S., Fine, M.E., Chung, Y.-W.: Effects of increased alloying element content on NiAl-type precipitate formation, loading rate sensitivity, and ductility of Cu- and NiAl-precipitation-strengthened ferritic steels. Acta Mater. 104, 166–171 (2016)
Wijnant, Y.H.: Contact Dynamics in the Field of Elastohydrodynamic Lubrication. Elsevier, Amsterdam (1998)
Wang, J., Hashimoto, T., Nishikawa, H., Kaneta, M.: Pure rolling elastohydrodynamic lubrication of short stroke reciprocating motion. Tribol. Int. 38, 1013–1021 (2005)
Wang, Q., Zhu, D.: Interfacial Mechanics: Theories and Methods for Contact and Lubrication First. CRC Press, Boca Raton (2019)
Wang, J., Kaneta, M., Yang, P.: Numerical analysis of TEHL line contact problem under reciprocating motion. Tribol. Int. 38, 165–178 (2005)
Liu, Y., Wang, Q.J., Wang, W., Hu, Y., Zhu, D.: Effects of differential scheme and mesh density on EHL film thickness in point contacts. J. Tribol. 128, 641–653 (2006). https://doi.org/10.1115/1.2194916
Wang, W.-Z., Li, S., Shen, D., Zhang, S., Hu, Y.-Z.: A mixed lubrication model with consideration of starvation and interasperity cavitations. Proc. Inst. Mech. Eng. Part J J. Eng. Tribol. 226, 1023–1038 (2012). https://doi.org/10.1177/1350650112460830
Pu, W., Wang, J., Zhu, D.: Progressive mesh densification method for numerical solution of mixed elastohydrodynamic lubrication. J. Tribol. (2015). https://doi.org/10.1115/1.4031495
Pu, W., Zhu, D., Wang, J.: A starved mixed elastohydrodynamic lubrication model for the prediction of lubrication performance, friction and flash temperature with arbitrary entrainment angle. J. Tribol. (2017). https://doi.org/10.1115/1.4037844
Liu, S., Qiu, L., Wang, Z., Chen, X.: Influences of iteration details on flow continuities of numerical solutions to isothermal elastohydrodynamic lubrication with micro-cavitations. J. Tribol. 143, 1–28 (2021). https://doi.org/10.1115/1.4049327
Qiu, L., Liu, S., Wang, Z., Chen, X.: Flow continuity of isothermal elastohydrodynamic point-contact lubrication under different numerical iteration configurations. J. Tribol. 144, 1–26 (2021). https://doi.org/10.1115/1.4051318
Liu, S., Wang, Q.J., Chung, Y.-W., Berkebile, S.: Lubrication-contact interface conditions and novel mixed/boundary lubrication modeling methodology. Tribol. Lett. 69, 164 (2021). https://doi.org/10.1007/s11249-021-01515-w
Liu, S., Wang, Q., Liu, G.: A versatile method of discrete convolution and FFT (DC-FFT) for contact analyses. Wear 243, 101–111 (2000)
Liu, S., Wang, Q.: Studying contact stress fields caused by surface tractions with a discrete convolution and fast fourier transform algorithm. J. Tribol. 124, 36–45 (2001). https://doi.org/10.1115/1.1401017
Bair, S., Flores-Torres, S.: The viscosity of polyalphaolefins mixtures at high pressure and stress. J. Tribol. 141, 021802 (2018). https://doi.org/10.1115/1.4041124
Caudwell, D.R., Trusler, J.P.M., Vesovic, V., Wakeham, W.A.: The viscosity and density of n-dodecane and n-octadecane at pressures up to 200 MPa and temperatures up to 473 K. Int. J. Thermophys. 25, 1339–1352 (2004). https://doi.org/10.1007/s10765-004-5742-0
Dowson, D., Higginson, G.R.: Elastohydro-Dynamic Lubrication. Pergamon Press, Oxford (1966)
Hesse, P.J., Battino, R., Scharlin, P., Wilhelm, E.: Solubility of gases in liquids. 20. Solubility of He, Ne, Ar, Kr, N2, O2, CH4, CF4, and SF6 in n-alkanes n-ClH2l+2 (6 ≤ l ≤ 16) at 298.15 K. J. Chem. Eng. Data 41, 195–201 (1996). https://doi.org/10.1021/je9502455
Plimpton, S.: Fast parallel algorithms for short-range molecular dynamics. J. Comp. Phys. 117, 1–19 (1995)
van Duin, A.C.T., Dasgupta, S., Lorant, F., Goddard, W.A.: ReaxFF: a reactive force field for hydrocarbons. J. Phys. Chem. A 105, 9396–9409 (2001). https://doi.org/10.1021/jp004368u
Shin, Y.K., Kwak, H., Vasenkov, A.V., Sengupta, D., van Duin, A.C.T.: Development of a ReaxFF reactive force field for Fe/Cr/O/S and application to oxidation of butane over a pyrite-covered Cr2O3 catalyst. ACS Catal. 5, 7226–7236 (2015). https://doi.org/10.1021/acscatal.5b01766
Stukowski, A.: Visualization and analysis of atomistic simulation data with OVITO–the Open Visualization Tool. Model. Simul. Mater. Sci. Eng. 18, 15012 (2009). https://doi.org/10.1088/0965-0393/18/1/015012
Wu, H., Khan, A.M., Johnson, B., Sasikumar, K., Chung, Y.-W., Wang, Q.J.: Formation and nature of carbon-containing tribofilms. ACS Appl. Mater. Interfaces 11, 16139–16146 (2019). https://doi.org/10.1021/acsami.8b22496
Hanesch, M.: Raman spectroscopy of iron oxides and (oxy)hydroxides at low laser power and possible applications in environmental magnetic studies. Geophys. J. Int. 177, 941–948 (2009). https://doi.org/10.1111/j.1365-246X.2009.04122.x
Shi, L., Rohringer, P., Suenaga, K., Niimi, Y., Kotakoski, J., Meyer, J.C., Peterlik, H., Wanko, M., Cahangirov, S., Rubio, A., et al.: Confined linear carbon chains as a route to bulk carbyne. Nat. Mater. 15, 634–639 (2016). https://doi.org/10.1038/nmat4617
Le, K.C., Lefumeux, C., Bengtsson, P.-E., Pino, T.: Direct observation of aliphatic structures in soot particles produced in low-pressure premixed ethylene flames via online Raman spectroscopy. Proc. Combust. Inst. 37, 869–876 (2019)
Le, K.C., Pino, T., Pham, V.T., Henriksson, J., Tӧrӧk, S., Bengtsson, P.-E.: Raman spectroscopy of mini-CAST soot with various fractions of organic compounds: structural characterization during heating treatment from 25 °C to 1000 °C. Combust. Flame 209, 291–302 (2019)
Trimm, D.L.: The formation and removal of coke from nickel catalyst. Catal. Rev. 16, 155–189 (1977). https://doi.org/10.1080/03602457708079636
Trimm, D.L.: Coke formation and minimisation during steam reforming reactions. Catal. Today 37, 233–238 (1997)
Sinfelt, J.H., Carter, J.L., Yates, D.J.C.: Catalytic hydrogenolysis and dehydrogenation over copper-nickel alloys. J. Catal. 24, 283–296 (1972)
Chen, H., Wu, P.Q., Quaeyhaegens, C., Xu, K.W., Stals, L.M., He, J.W., Celis, J.-P.: Comparison of fretting wear of Cr-rich CrN and TiN coatings in air of different relative humidities. Wear 253, 527–532 (2002)
Vera, E., Manuel, V.-T., Lewis, R., Gallardo, E., Laguna-Camacho, J.R.: A study of the wear performance of TiN, CrN and WC/C coatings on different steel substrates. Wear 271, 2116–2124 (2011)
Paskvale, S., Remškar, M., Čekada, M.: Tribological performance of TiN, TiAlN and CrN hard coatings lubricated by MoS2 nanotubes in Polyalphaolefin oil. Wear 352–353, 72–78 (2016)
Acknowledgements
The authors would like to thank the support from U. S. National Science Foundation (Grant No. CMMI-1662606). The authors would also like to thank Valvoline for providing the PAO-4 fluid. This work made use of the MatCI Facility which receives support from the MRSEC Program (NSF DMR- 1720139) of the Materials Research Center at Northwestern University and the SPID facility of Northwestern University’s NUANCE Center, which has received support from the Soft and Hybrid Nanotechnology Experimental (SHyNE) Resource (NSF ECCS-1542205), the MRSEC program (NSF DMR-1720139) at the Materials Research Center, the International Institute for Nanotechnology (IIN) at Northwestern University, the Keck Foundation, and the State of Illinois through IIN. This research was supported in part through the computational resources and staff contributions provided for the QUEST high performance computing facility at Northwestern University, which is jointly supported by the Office of the Provost, the Office for Research, and Northwestern University Information Technology. Research was sponsored by the Army Research Laboratory and was accomplished under Cooperative Agreement Numbers W911NF-20-2-0230 and W911NF-20-2-0292. The views and conclusions contained in this document are those of the authors and should not be interpreted as representing the official policies, either expressed or implied, of the Army Research Laboratory or the U.S. Government. The U.S. Government is authorized to reproduce and distribute reprints for Government purposes notwithstanding any copyright notation herein.
Funding
Funding was provided by DEVCOM Army Research Laboratory (W911NF-20-2-0230 and W911NF-20-2-0292).
Author information
Authors and Affiliations
Contributions
A.M.K, Y.W.C, Q.J.W. and S. B. framed the research scope. A.M.K. wrote the initial manuscript, specifically sections abstract, 1, 2.1, 2.2, 2.4, 3.1, 3.2, and 3.3. J.A. wrote the sections pertaining to molecular dynamics simulations (sections 2.5 and 3.5). S.L. wrote section 2.3. T.M. wrote section 3.4. Y.W.C and Q.J.W wrote section 4. All authors reviewed the manuscript.
Corresponding authors
Ethics declarations
Conflict of interest
All authors declare that they have no conflicts of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Below is the link to the electronic supplementary material.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Khan, A.M., Ahmed, J., Liu, S. et al. Formation of Wear-Protective Tribofilms on Different Steel Surfaces During Lubricated Sliding. Tribol Lett 71, 63 (2023). https://doi.org/10.1007/s11249-023-01735-2
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s11249-023-01735-2