A method for calculating the fields of parameters of the stress-strain state at the crack tip for mixed modes of loading is developed and implemented taking into account the higher-order terms. The influence of the final crack tip curvature radius on the parameters characterizing the mixed failure modes under plane strain is shown. The nature of influence of the mixed modes of loading and the crack geometry on the behavior of dimensionless angular characteristics of the second term in the expansion of the stresses in the plastic crack tip region is established from the calculation results. The relationships between the mixing, constraint and triaxiality parameters are derived in a full range of mixed deformation modes.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
M. Siratori, T. Miyoshi, and H. Matsushita, Computational Mechanics of Fracture [Russian translation], Mir, Moscow (1986).
J. W. Hutchinson, “Plastic stress and strain fields at a crack tip,” J. Mech. Phys. Solids, 16, 337–347 (1968).
J. W. Hutchinson, “Singular behavior at the end of a tensile crack in a hardening,” J. Mech. Phys. Solids, 16, 13–31 (1968).
J. R. Rice and G. F. Rosengren, “Plane strain deformation near a crack tip in a power-law hardening material,” J. Mech. Phys. Solids, 16, 1–12 (1968).
Y. Li and Z. Wang, “High-order asymptotic field of tensile plane-strain nonlinear crack problems,” Scientia Sinica, 29A, 941–955 (1986).
S. M. Sharma and N. Aravas, “Determination of higher-order terms in asymptotic elastoplastic crack tip solutions,” J. Mech. Phys. Solids, 39, 1043–1072 (1991).
N. P. O’Dowd and C. F. Shih, “Family of crack-tip fields characterized by a triaxiality parameter. I. Structure of fields,” J. Mech. Phys. Solids, 39, 987–1015 (1991).
C. F. Shih, “Small-scale yielding analysis of mixed plane strain crack problem,” in: Fracture Analysis, ASTM STP 560, Philadelphia (1974), pp. 187–210.
C. Betegon and J. W. Hancock, “Two-parameter characterization of elastic-plastic crack-tip fields,” J. Appl. Mech., 58, 104–110 (1991).
F. Erdogan and G. C. Sih, “On the crack extension in plates under plane loading and transverse shear,” J. Basic Eng. (Trans. ASME), Ser. D, 85, 519–527 (1963).
V. V. Panasyuk, The Limiting Equilibrium of Brittle Bodies with Cracks [in Russian], Naukova Dumka, Kiev (1968).
V. A. Dolgorukov and V. N. Shlyannikov, “Elastic-plastic stress functions for Mode I and Mode III cracks,” in: Applied Problems of Strength and Plasticity. Solution Methods [in Russian] (1988), pp. 49–55.
V. N. Shlyannikov, Elastic-Plastic Mixed Mode Fracture Criteria and Parameters, Springer, Berlin (2003).
V. N. Shlyannikov and S. Yu. Kislova, “Calculation-and-experimental justification of the crack growth direction criterion,” Zavod. Lab., 75, No. 10, 41–45 (2009).
J. Eftis and N. Subramaniyan, “The inclined crack under biaxial load,” Eng. Fract. Mech., 10, 43–67 (1978).
D. S. Henry and A. R. Luxmoore, “The stress triaxiality constraint and the Q-value as a ductile fracture parameter,” Eng. Fract. Mech., 57, 375–390 (1997).
Author information
Authors and Affiliations
Additional information
Translated from Problemy Prochnosti, No. 6, pp. 44–63, November–December, 2010.
Rights and permissions
About this article
Cite this article
Shlyannikov, V.N., Kislova, S.Y. Parameters of deformation mixed modes with account of crack tip curvature. Strength Mater 42, 660–674 (2010). https://doi.org/10.1007/s11223-010-9254-9
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11223-010-9254-9