The paper considers the process of creation of an aluminum bronze-based metal-matrix composite straightened with tungsten carbide particles by the method of electron-beam additive manufacturing. To create composites, a combined printing method with powder and wire material feeding has been used. The microstructure study showed that varying the printing parameters during the process has made possible to achieve a homogeneous distribution of particles of the strengthening phase in the matrix. Carbide particles undergo refining caused by the electron beam. The particles size of obtained composite is 4 times finer compared to the initial powder size. Dry sliding wear studies showed strong wear character and dependence of the friction coefficient on the hardening particles size.
Similar content being viewed by others
References
W. Li, Y. Yang, M. Li, et al., Mater. Des., 141, 57–66 (2018).
H. Singh, S. Kumar S., and D. Kumar, Mater. Sci. Eng. A, 789, 139577 (2020).
E. E. Feldshtein and L. N. Dyachkova, Wear, 444–445, 203161 (2019).
J. Kumar, D. Singh, N. S. Kalsi, et al., J. Mat. Res. Technol., 12, 930–946 (2021).
D. Madhesh, K. Jagatheesan, T. Sathish , and K. Balamanikandasuthan, Materials Today: Proc., 37, No. 2, 1437–1441 (2021).
A. Bahador, J. Umeda, R. Yamanoglu, et al., J. Alloys Compd, 847, 156555 (2020).
V. A. Kumar, M. P. Anil, G. L. Rajesh, et al., Mater. Today: Proc., 5, No. 8, 16141–16145 (2018).
G. Nageswaran, S. Natarajan, and K. R. Ramkumar, J. Alloys Compd., 768, 733–741 (2018).
K. Dash, B. C. Ray, and D. Chaira, J. Alloys Compd., 516, 78–84 (2012).
S. Buytoz, F. Dagdelen, S. Islak, et al., J. Therm. Anal. Calorim., 117, No 3, 1277–1283 (2014).
P. Jena, E. Brocchi, and M. Motta, Mater. Sci. Eng. A, 313, Nos. 1–2, 180–186 (2001).
A. V. Filippov, E. S. Khoroshko, N. N. Shamarin, et al., J. Alloys Compd., 859, 157824 (2021).
Z. Sheng, D. Minglu, W. Lu, et al., Mater. Des., 217, 110635 (2022).
M. P. Ethan and Z. S. Saba, Addit. Manuf., 50, 102450 (2022).
W. Di, H. Jinhui, T. Chaolin, et al., Mater. Sci. Eng. A, 841, 143018 (2022).
S. V. Razorenov, G. V. Garkushin, A. S. Savinykh, et al., Phys. Mesomech., 25, 26–32 (2022).
L. Chen, Z. Hou, Y. Liu, et al., Compos. Part A Appl. Sci., 138, 106063 (2020).
H. Zhou, P. Yao, T. Gong, et al., Tribol. Int., 138, 380–391 (2019).
H. Zhou, P. Yao, Y. Xiao, et al., Tribol. Int., 132, 199–210 (2019).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Moskvichev, E.N., Shamarin, N.N. & Filippov, A.V. Friction and Wear Perfomance of WC Reinforced Aluminum Bronze Produced by EBAM Technique. Russ Phys J 65, 1598–1604 (2023). https://doi.org/10.1007/s11182-023-02807-5
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11182-023-02807-5