Abstract
Applying a newly proposed method for the synthesis of a binary system Al2O3/B2O3, a series of metal phase supports with the ratio of B:Al components varied in the range from 0.05 to 1 was obtained. The supports were loaded with a metal phase from the water solution of H2PtCl6 to get the final load of 1 % of the metallic phase. The samples were subjected to thermal treatment under oxidizing or reducing conditions. The degree of dispersion of the metal phase, evaluated on the basis of hydrogen chemisorption, was very high, reaching a maximum of over 150 %. The catalytic performance of the catalysts was tested in the reaction of temperature-programmed complete oxidation of 1-butene.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
As indicated by recent literature reports [1], the catalytic centers related to the atomically dispersed noble metals can be considered in the aspect of metal interacting with the surface ligand present on the surface of a solid support. This consideration can be applied both to uniform crystalline structures, e.g. zeolites, as well as to oxide supports. The possibility of noble metal existence (i) under difficult reaction conditions, (ii) on easily reducible oxide supports (e.g. cerium oxide), in the form of subnanometric clusters (iii) or in atomic dispersion has brought about a new approach to Taustner’s idea of strong interaction between the metal and cluster support [2, 3]. The cations of platinum, palladium, rhodium or other metals, anchored to the support through the M–O bonds can form in the configurations that are stable and catalytically active in a few reactions, in particular, oxidation and reduction. It is expected that development of effective methods for the synthesis and identification of suitable stabilizers and promoters will bring an increased range of cost-effective applications of atomically dispersed noble metal based catalysts. In heterogeneous catalysis, the distribution of active centers in which individual atoms or clusters of atoms are catalytically active can be compared to the molecular catalysis in a homogeneous catalytic system, which can grow links between these two types of catalysis. A binary oxide system, Al2O3/B2O3, has been applied in many reactions based on the use of heterogeneous catalysts. Thanks to its acidity, this system can be used in the reactions of Beckmann rearrangement [4–10], alcohol dehydration [11–14], partial oxidation of olefins [15–19], cracking [20–23], isomerization of hydrocarbons [24, 25] and toluene disproportionation [25, 26]. On the other hand, this system proved to be an effective support of metallic phase active in a number of reactions important for industry, like in the reactions of metathesis where it was a support of rhenium [27, 28], cyclohexene hydrogenation, where it was a support of platinum [29] or carbon oxide hydrogenation as a support of ruthenium [30]. The versatile character and multifunctional applications of this support are related to its specific acidic properties. It is known that the catalytic activity of platinum on oxide support depends to a considerable degree on the strength of acidic centers or on the general acid–base character of the support. Moreover, not only the activity but also the degree of dispersion significantly increases with increasing acidity of the support. Yazawa et al. [31], on the basis of interpretation of the XANES spectra of the catalysts: Pt/SiO2, Pt/Al2O3/, Pt/MgO, have shown that for the supports of basic character under oxidizing conditions, platinum has an increased tendency towards occurrence in oxidized states. As a consequence, the degree of its dispersion decreases and its activity in the reactions of oxidation or total combustion decreases. The literature provides many reports on the reduced activity of platinum in the reactions of hydrocarbon combustion, in the presence of surface forms of PtOx. This phenomenon is related to a greater mobility of this phase on the surface of oxide supports, leading to coalescence of Pt.
The main aim of the study was to design a binary system Al2O3–B2O3 to be a support for a catalyst with a metal (Pt) phase. In view of the earlier studies performed on similar binary gels [32–36] with Al2O3 or SiO2 as a matrix, a similar approach was applied in the design and synthesis of a catalyst with metal phase. The proposed method for the synthesis of a binary oxide support based on employing sol–gel processes, permitted the elimination of the presence of inorganic additives that could obscure the process of interaction between the metal phase precursor and the support surface.
Experimental
Synthesis
The supports of the metal phase were the samples of grain size from 0.1 to 0.2 mm, obtained according to the procedure described in [34, 35]. The precursor of the metal phase was a standard water solution of hexachloroplatinic acid [H2(PtCl6)] containing 14.28 g Pt/dm3. Proper amounts of the solution were deposited on the surface of gel support by the method of incipient wetness impregnation, then the samples were dried in a vacuum evaporator at 100 °C for 8 h. The precursor was transformed to the metal phase by thermally programmed reduction in H2 atmosphere, on temperature increasing at the rate of 5°/min, with 10 min plateaus at 100 and 200 °C and a 180 min plateau at 250 °C. The final temperature of annealing was 500 °C at which the samples were kept for about 60 min. The process of cooling to 200 °C was also performed in H2 atmosphere, which was afterwards replaced by 99.99 % He as a cooling medium and continued to room temperature. The catalyst loading with metal phase was the same in all samples and equal to 1 weight percent (wt%).
Surface area
The surface area was determined by the low temperature (77 K) nitrogen adsorption measurements carried out on the Accelerated Surface Area and Porosimetry System model 2010 V2.00 D made by Micromeritics, using 200–300 mg of the support with the grain size fraction between 0.1 and 0.2 mm. Prior to nitrogen adsorption, all samples were outgassed at 623 K (350 °C) at 0.4 Pa till constant weight. Both the adsorptive and desorptive branches of the isotherm were taken in the range of p/p0 0–1.
IR spectroscopy
Spectroscopic studies were carried out in a Bruker IFS 66 vacuum infrared spectrometer. The sample was placed in a water cooled cuvette, enabling a heat treatment up to 800 °C. The sample was heated at 750 °C under low pressure (10−3 mmHg) for 1 h before measurement. 10 μl of D2O was added to adsorb on the sample surface prior to sequence of thermal desorption at 300 °C (II), 450 °C (II), 600 °C (II), 750 °C (II) for 30 min (10−3 mmHg vacuum) and spectra measurement.
Metal dispersion
Chemisorption experiments using hydrogen were performed at 35 °C in a Micromeritics ASAP (Accelerated Surface Area and Porosimetry System) model 2010 V2.00 D equipped with a chemisorption controller station. The procedure of H2 chemisorption on the samples obtained after thermally programmed reduction included degassing (10−5 mmHg) at 500 °C (1 h) followed by annealing in H2 atmosphere for 1 h at 500 °C and repeated degassing for 2 h at 500 °C. After these processes, the samples were cooled to 35 °C at which hydrogen was adsorbed. After the first adsorption, the samples were degassed for 2 h at 35 °C and then hydrogen was adsorbed again in order to establish the amount of weak adsorbed hydrogen. The difference in measurements 1 and 2 provided information on the amount of strongly chemisorbed hydrogen. The degree of dispersion was calculated assuming that the stoichiometry of adsorption is 1 hydrogen atom per 1 platinum atom. For the system BAl 0.4, measurements of adsorption were also performed at 100 and 200 °C under the same activation conditions.
Catalytic combustion of 1-butene
The activities of catalysts obtained were tested in the reaction of oxidation of 1-butene to CO2, which was performed according to the rules of thermally programmed reactions (TPRe) [37]. The reaction system included a Pfeiffer gas analyzer ThermoStar, model GSD 301 T2, with a QMA 200 M mass analyzer and a Faraday trap used as a detector, for the mass range: 1–200 amu. Analysis of the reaction gases was made with the use of the software Pfeiffer Vacuum Quadstar. The contents of CO2, CxHy and H2O were measured. The carrier gas and oxidizing agent was air. The stream of carrier gas dried on the adsorption column packed with zeolite 4A and 1-butene were directed to the mixer. The composition of the reactor feed was controlled by mass flow controllers. The concentration of 1-butene in the carrier gas (air) was 2000 ± 100 ppm. The internal diameter of the fixed-bed reactor was 6 mm. A portion of 60 mg of the catalyst was placed in a glass microreactor, a stream of the reaction mixture was fed on it and the temperature program was started. The rate of temperature increase was 20 º/min and the progress of reaction was recorded in the temperature range 308–673 K (35–400 °C). After the completion of the first measurement, the catalyst was cooled to 308 K (35 °C) in the reaction mixture stream containing 1-butene. After reaching 308 K (35 °C), the catalyst sample was subjected to the same procedure in combustion of 1-butene for the second time (followed activation).
Electron microscopy
Transmission electron microscopy images were taken on a microscope TEM JEOL 200 CX made by Jeol. The images were recorded using the anode voltage of 80 kV. The processing, image analyses and crystallites size measurements were made using the program Gwyddion (GPL).
Discussion
The ability to control the dispersion of precious metals (e.g., Pt, Pd) supported on oxide surfaces is a primary goal of the catalysts design and may lead to understanding the nature of metal-support interaction. The dispersion of these metals on the oxide supports is a critical factor because of the high cost of noble metals. As follows from the data presented in Table 1, for almost all binary oxide systems obtained (B2O3/Al2O3), the dispersion of Pt (H/Pt) was higher than in the system Pt/Al2O3, for which the degree of platinum dispersion determined on the basis of hydrogen chemisorption H/Pt was 1.07. It should be noted that the changes in the degree of dispersion of the metal phase is very similar to that of changes in the surface area, depending on the content of the boria containing component (B2O3) in the Al2O3 matrix (Table 1). The values of surface area SBET and the degree of metal phase dispersion (H/Pt) are higher for B2O3/Al2O3 than for the support not modified with boria, and these values increase to reach a maximum for the sample of B/Al molar ratio of 0.3. A clearly visible correlation between these values evidences that the metal phase dispersion depends on the surface area (geometry) of the support.
For significant changes in the surface area of the systems studied (for Al2O3 gel the surface area is 337 m2 g−1, while for the samples of B/Al 0.1, 0.2 and 0.3, it is above 500 m2 g−1 [35] and the only sample with the highest content of B2O3 (B/Al 1.0) has a slightly lower surface area (317 m2 g−1), which is associated with the process boria of crystallization) more informative is presentation of the metal phase area (Pt), determined on the basis of H2 adsorption isotherm, expressed per a unit area of the support, as shown in Fig. 1.
The normalized area of Pt per 1 m2 of the support determined on the basis of strongly and poorly adsorbed hydrogen H2. Experimental conditions: degassing (10−5 mmHg) 1 h 500 ºC, annealing in H2, 1 h, 500 ºC, repeated degassing, 2 h, 500 ºC After the 1st adsorption, cooled to 35 ºC and degassed (10−5 mmHg) 2 h, 35 ºC and 2nd was taken
In general, the character of changes in the normalized area of Pt per 1 m2 of the support taking place in response to increasing contribution of B2O3 in the Al2O3 matrix is very similar to that of changes in Pt dispersion degree shown in Table 1.
It should be noted that for sample B/Al 1.0, the values of Pt area per 1 m2 of the support are similar to those obtained for sample B/Al 0.3. Taking into account the fact that the surface areas of these two samples differ by over 200 m2 g−1 (that of the sample with a lower content of boron was larger), it can be supposed that development of surface area of the support (depending on the content of boria) was not the main factor determining the relatively high amount of chemisorbed H2. This is illustrated in Fig. 1 by a large area of Pt per 1 m2 of the support for the sample with the highest content of B2O3 (B/Al = 1.0).
It is well known that the interaction of Pt particles with the oxide support can alter the electronic properties of the Pt and play a crucial role determining the particle morphology and maintaining the dispersion of Pt. For example, high dispersion can be achieved by specific interaction between defect sites on the support surface [38]. On the other hand, it has been confirmed that platinum on acidic supports is more electron-deficient than that on basic ones [39, 40] and platinum on the acidic support material is less oxidized than that on the basic one. Analysis of the crystallite size of the metal phase (Pt) in the TEM images recorded confirmed a high dispersion, or indicated that the metal phase occurs as a monolayer on the surface of the support. Very small crystallites of platinum can be identified in the TEM images, in contrast to their presence in the analogous gel systems Al2O3/SnO2 or Al2O3/GeO2 system (Supplementary Information). For these gel systems, Pt crystallites of the size from 8 to 90 nm were observed. Their size was dependent on the composition of the support. For the systems with a smaller content of SnO2, e.g. Sng 0.2 (Fig. 4e), the crystallites are smaller, of the size from 8 to 25 nm, while for the sample Sng 1.0 (molar ratio SnO2:Al2O3 of 1:1), they are much greater, of the size 40–90 nm. For the systems modified with germanium(IV) oxide, the dispersion was much smaller than for the systems modified with B2O3 and did not exceed 10 %. Increased dispersion was achieved only for the sample with a small content of GeO2 (molar ratio of Ge/Al = 0.05 at the Pt loading up to 0.5 wt%; for this sample, the dispersion reached about 23 % and the Pt crystallites reached ~40 nm.
The dispersion values obtained for the samples B2O3–Al2O3 of over 100 % are contradictory to the theoretically possible maximum dispersion of the metal. The error of chemisorption measurements for the systems H/Pt, O/Pt and CO/Pt can reach up to 10 % [41] so these results cannot be explained by the instrumental error. The measurements were repeated after a few months and confirmed the earlier obtained values with the maximum deviation of 4 %. The results of H2 chemisorption at elevated temperatures (Fig. 2) reveal that the higher the electron deficiency of the support (the more acidic it is), the stronger the bonds with the surface Pt atoms. For small metal clusters made of 2–20 atoms, the energy of H/Pt bonding is much higher than that for the atoms of surface crystallites of the size greater than 2 nm [42], and the atoms at the at the vertices, and edges of the clusters show increased ability of H2 molecule adsorption. According to the theoretical calculations based on the Hückel model, for the clusters from Pt2 to Pt13, the value of H/Mmax varies from 5 to 1.9 [43].
The effect of temperature on the amount of chemisorbed hydrogen for sample BAl 0.4. Experimental conditions: degassing (10−5 mmHg) 1 h 500 ºC, annealing in H2, 1 h, 500 ºC, repeated degassing, 2 h, 500 ºC. The 1st adsorption at 35, 100 and 200 ºC. After the 1st adsorption degassed (10−5 mmHg) 2 h, 35, 100 and 200 ºC and the 2nd was taken
The supports obtained containing boron oxide show much higher acidity and have strong acidic Brønsted type centers, whose presence was excluded for the reference systems SnO2 and GeO2. On the other hand, an additional factor leading to the high dispersion of the metal phase and its stabilization is the matching of sizes of the metal crystallites to the pores in the oxide support. This hypothesis put forward in the 1950s by Boreskov [44] has attracted renewed interest and confirmation [45].
For Pt supported on Al2O3/SnO2, it is difficult to relate the drastic decrease in Pt dispersion with mean size of pores on the support surface (Fig. 3). It can be supposed that for the easily reducible component SnO2, the reason for reduced dispersion of Pt is formation of alloys of Pt with Sn. For the samples modified with boron oxide, there is a correlation between the degree of dispersion and the mean size of pores (Fig. 3). With decreasing pore diameter, the degree of dispersion increases. Of course, it is not possible to conclude from the above about the dominant role of this mechanism of stabilization, but it cannot be disregarded when considering the full spectrum of interactions.
Gel formulations containing B2O3 are difficult to study in infrared spectroscopy (area “cut-of” below 1600 cm−1 and have broad unresolved band stretching vibration of hydroxyl or hydrogen bond linked to the associates). Thus, the use of molecular probes is in most cases difficult or impossible. On the other hand, the transmission IR spectrum of the binary oxide systems (subjected to a dehydration and dehydroxylation at temperatures above 500 °C) indicate that the surface of only the hydroxyl groups are bonded to the boron (3685–3693 cm−1). D2O adsorption on this surface leads to the bandwidth derived from stretching vibration of O–D (2723 cm−1) resulting from the adsorption of D2O to the Lewis acid centers (Fig. 4). Taking into account that boric acid (formed by the reaction of B2O3 with H2O/D2O) is exclusively monobasic acid that acts not as a proton donor, but as a Lewis acid accepting OD−, it can be assumed that these groups are associated with exposed surface boron ions.
Taking into account that the catalytic reaction of hydrocarbons combustion is very important from the technological viewpoint for production of energy, the test reaction chosen was combustion of 1-butene. The reaction of full combustion of 1-butene permitted evaluation of the effect of addition of boron oxide on the activity of catalysts with supported metal phase, on the basis of measurement of temperature at which full conversion of 1-butene is observed for a given catalyst.
With increasing content of B2O3 in the support, the temperature of maximum conversion of 1-butene decreases at first, reaching a minimum for sample Pt/BAl 0.3 and then increases. The character of Tmax changes is similar to that of the changes in Pt dispersion (H/Pt) presented in Table 1. It should be noted that the Pt catalysts supported on binary oxide systems B2O3–Al2O3 reach a maximum activity at about 200 °C, which is by 50 °C lower than for Pt/Al2O3.
The temperature programmed reaction was performed in two subsequent tests. After the first catalytic test, the catalyst was subjected to thermal treatment at 400 °C, and then to the repeated test in TPR conversion of 1-butene. As follows from the plots in Fig. 5, the results of the second catalytic test are better than those of the first one, allowing a lower temperature of full 1-butene combustion. It seems that the presence of B2O3 in the Al2O3 matrix leads not only to a high degree of Pt dispersion but also limits the generation of PtOx particles able to move on the support surface, so stabilizes the metal dispersion.
Conclusions
The results presented have shown that modification of Al2O3 with boron oxide is highly beneficial, not only because of the high dispersion values obtained but also because an increase in the content of B2O3 does not reduce the dispersion but maintains it on a similar level. In the supports modified with B2O3, the high metal dispersion is not related to strong metal-support interactions, as e.g. in SnO2, but the porous structure of the support that stabilizes small metal clusters on the surface. Another factor conducive to the stabilization of small clusters of Pt groups is the acidic character of the support surface caused by the presence of boron oxide. It seems that the old theory proposed by Boreskov [44] is confirmed by the results presented and perhaps it should play an important role in designing systems with nanometallic phase.
References
Flytzani-Stephanopoulos M, Gates BC (2012) Annu Rev Chem Biomol Eng 3:545–574
Tauster SJ, Fung CS (1978) J Catal 55:29–35
Tauster SJ, Fung SC, Garten RL (1978) J Am Chem Soc 100:170–175
Curtin T, McMonagle JB, Hodnett BK (1992) Appl Catal A 93:91
Izumi Y, Sato S, Urabe K (1983) Chem Lett 1649–1652
Werke L (1955) East Ger Patent 10920
Irnich R (1976) BASF Ger Patent 1227028
Immel O, de Jager A, Kaiser BU, Schwarz HH (1978) Bayer Jpn Patent S53-037686
Murakami Y, Saeki Y, Ito K (1972) Nippon Kagakukaishi 1:12
Sakurai H, Sato S, Urabe K, Izumi Y (1985) Chem Lett 1783–1784
Delmastro A, Gozzelino G, Mazza A, Vallino M, Busca G, Lorenzelli V (1994) J Chem Soc 90:2663
Wang WJ, Che YW (1991) Che Catal Lett 10:297
Peil K, Galya LG, Marcelin G (1989) J Catal 115:441
Engels S, Herold E, Lausch H, Mayr H, Meiners HW, Wilde M (1992) In: Proceedings of the 10th international congres on catalysis, p 2581
Murakami Y, Otsuka K, Wada Y, Morikawa A (1990) Bull Chem Soc Jpn 63:340
Cucinieri-Colorio G, Auroux A, Bonnetot B (1993) J Term Anal 40:1267
Cucinieri-Colorio G, Bonnetot B, Védrine JC, Auroux A (1994) New developments in selective oxidation II. In Cortés Corberán V, Vic Bellón S (eds), Elsevier Science Publishers, p 143
Colorio G, Ve´drine JC, Auroux A, Bonnetot B (1996) Appl Catal A 137:55
Buyevskaya OV, Kubik M, Baerns M (1996) Symposium on heterogeneous hydrocarbon oxidation presented before the division of petroleum chemistry, Inc., 211th national meeting, American Chemical Society, p 163
Pine L (1976) US Patent 3,993,557
Bailey WA (1945) US Patent 2,377,744
De Bataafsche NV (1949) Petroleum Maatschappij te’s-Gravenhage Dutch Patent 62,287
De Bataafsche NV (1950) Petroleum Maatschappij te’s-Gravenhage Dutch Patent 65,287
Sato S, Kuroki M, Sodesawa M, Nozaki T, Maciel GE (1995) J Mol Catal 104:171
Izumi Y, Shiba T (1964) Bull Chem Soc Jpn 37:1797
Tanabe K (1970) Solid acids and bases. Academic press, New York, p 131
Xiaoding X, Boelhouwer C, Benecke JI, Vonk D, Mol JC (1986) J Chem Soc 1(82):1945
Sibeijn M, van Veen JAR, Bliek A, Moulijn JA (1994) J Catal 145:416
Chen YW, Li C (1992) Catal Lett 13:359
Okihara T, Tamura H, Misono MJ (1995) J Catal 95:41
Yazawa Y, Yoshida H, Tahagi N, Kagi N, Komai S, Satsuma A, Murakami Y, Hattori T (2000) In: 12th international congress on catalysis (Stud Surf Sci Catal, vol 130), p 2189
Kirszensztejn P, Szymkowiak A, Marciniak P, Martyla A, Przekop R (2003) Appl Catal 245:159–166
Kirszensztejn P, Przekop R, Szymkowiak A, Mackowska E, Gaca J (2006) Microporous Mesoporous Mater 89:150–157
Martyła A, Olejnik B, Kirszensztejn P, Przekop R (2011) Int J Hydrog Energy 36:8358–8364
Przekop R, Kirszensztejn P (2014) J Non Cryst Solids 402:128–134
Nowicki W, Rypka G, Kawałko A, Tolińska A, Kirszensztejn P (2014) J Mater Sci 49:4416–4422
Falconer JL, Schwarz JA, Catal J (1983) Rev Sci Eng 25:141–227
Kwak JH, Hu J, Mei D, Yi CH-W, Kim DH, Peden CHHF, Allard LF, Szanyi J (2009) Science 325:1670–1673
Ishihara T, Harada K, Eguchi K, Arai H (1992) J Catal 136:161
Yazawa Y, Takagi N, Yoshida H, Komai S, Satsuma A, Tanaka T, Yoshida S, Hattori T (2002) Appl Catal A 233:103–112
Alexeev OS, Graham GW, Shelef M, Gates BC (2000) J Catal 190:157
Cremaschi P, Whitten JL (1987) Chem Mater Sci 72:485
Minot C, Bigot B, Hariti A (1986) J Am Chem Soc 108:196
Boreskov GK, Karnauchov AP (1952) Ż F Ch 26:26
Zou W, Gonzales RD (1993) Appl Catal A 102:181–200
Author information
Authors and Affiliations
Corresponding author
Electronic supplementary material
Below is the link to the electronic supplementary material.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Przekop, R.E., Kirszensztejn, P. Highly dispersed Pt on B2O3/Al2O3 support: catalytic properties in the total oxidation of 1-butene. Reac Kinet Mech Cat 118, 325–335 (2016). https://doi.org/10.1007/s11144-016-1006-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11144-016-1006-9