Skip to main content
SpringerLink
Log in

Thermal parameters for centrifugal induction sintering of powder coatings

  • EXCHANGE OF EXPERIENCE
  • Published:
Powder Metallurgy and Metal Ceramics Aims and scope

An engineering method for thermal analysis of centrifugal induction sintering is developed. The method allows for the geometrical, thermal, and electrophysical parameters of parts and powder layer and the joint effect of convective and radiant heat transfer on the outer surface of parts. Formulas are derived to determine the temperature distribution over a part from the temperature on the outer surface needed for powder layer sintering. A system to monitor and control temperature in centrifugal induction sintering is developed.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. N. N. Dorozhkin, L. P. Kashitsin, T. M. Abramovich, and I. A. Kirpichenko, Centrifugal Sintering of Powder Coatings under Variable Mechanical Loads [in Russian], V. G. Gorobtsov (ed.), Nauka i Tekhnika, Minsk (1993), p. 159.

    Google Scholar 

  2. N. N. Dorozhkin, T. M. Abramovich, and V. I. Zhornik, Sintering of Coatings [in Russian], Nauka i Tekhnika, Minsk (1980), p. 176.

    Google Scholar 

  3. N. N. Dorozhkin, V. A. Kot, and L. P. Kashitsin, Recommendations to Select Process Parameters for Induction Sintering and Deposition [in Russian], INDMash AN BSSR, Minsk (1982), p. 60.

    Google Scholar 

  4. N. N. Dorozhkin, A. I. Zhornik, V. A. Zhornik, et al., An Introduction to the Physics of Solid, Liquid, and Porous Bodies. Part II [in Russian], N. N. Dorozhkin (ed.), Izd. Taganrog Gos. Pedagog. Inst., Taganrog (2001), p. 135.

    Google Scholar 

  5. A. E. Slukhotskii and S. E. Ryskin, Inductors for Induction Heating [in Russian], Énergiya, Leningrad (1974), p. 264.

    Google Scholar 

  6. H. B. Dwight, Tables of Integrals and Other Mathematical Data, The Macmillan Company, New York (1961).

    Google Scholar 

  7. G. A. Korn and T. M. Korn, Mathematical Handbook for Scientists and Engineers. Definitions, Theorems and Formulas for Reference, and Review, McGraw-Hill Book Company Inc., New York–Toronto–London (1961).

    Google Scholar 

  8. D. Dropkin and A. Karmi, “Natural–convention heat transfer from a horizontal cylinder rotating in air,” Trans. ASME, 9, No. 4 (1957).

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. State Scientific Establishment “Powder Metallurgy Institute,” National Academy of Sciences of Belarus, Minsk, Belarus

    Yu. N. Gafo

  2. Joint Mechanical Engineering Institute, National Academy of Sciences of Belarus, Minsk, Belarus

    I. A. Sosnovskii

Authors
  1. Yu. N. Gafo
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. I. A. Sosnovskii
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to I. A. Sosnovskii.

Additional information

Translated from Poroshkovaya Metallurgiya, Vol. 48, No. 1–2 (465), pp. 134–143, 2009.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Gafo, Y.N., Sosnovskii, I.A. Thermal parameters for centrifugal induction sintering of powder coatings. Powder Metall Met Ceram 48, 105–111 (2009). https://doi.org/10.1007/s11106-009-9087-x

Download citation

  • Received:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11106-009-9087-x

Keywords

Search

Navigation