Skip to main content
SpringerLink
Log in

Effect of Preliminary Heat Treatment on Deformation of Brass by the Method of ECAP

  • DEFORMATION
  • Published:
Metal Science and Heat Treatment Aims and scope

The deformability of brass L63 under equal-channel angular pressing (ECAP) after a preliminary heat treatment (annealing at 600°C or quenching from different temperatures) is studied. The ECAP is conducted at room and elevated temperatures. It is shown that ECAP of brass L63 is possible only at elevated temperatures after preliminary annealing.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
Fig. 5.

Similar content being viewed by others

References

  1. I. Yu. Litovchenko, S. A. Akkuzin, I. A. Polekhina, and A. N. Tyumentsev, “Effect of thermomechanical treatments on formation of submicrocrystalline structural state and mechanical properties of metastable austenitic steel,” Pis’ma Mater., No. 4(24), 290 – 293 (2016).

    Google Scholar 

  2. G. G. Kurapov, E. P. Orlova, I. E. Volokitina, and A. Turdaliev, “Plasticity as a physical-chemical process of deformation of crystalline solids,” J. Chem. Technol. Metall., 51, 451 – 457 (2016).

    CAS  Google Scholar 

  3. A. V. Zinov’ev, D. W. Ming, P. Yu. Sokolov, et al., “Effect of temperature and rate parameters on deformation resistance of plain brasses,” Proizvod. Prokata, No. 10, 308 (2014).

    Google Scholar 

  4. I. E. Volokitina and G. G. Kurapov, “Effect of initial structural state on formation of structure and mechanical properties of steels under ECAP,” Metal. Sci. Heat Treat., 59(11 – 12), 786 – 792 (2018).

    Article  CAS  Google Scholar 

  5. G. J. Raab, R. Z. Valiev, Y. T. Zhu, and T. C. Lowe, “Continuous processing of ultrafine grained Al by ECAP,” Conform. Mater. Sci. Eng., 382, 30 – 34 (2004).

    Article  Google Scholar 

  6. A. A. Gazder, Torre F. Dalla, C. F. Gu, et al., “Microstructure and texture evolution of bcc and fcc metals subjected to equal channel angular extrusion,” Mater. Sci. Eng., 415, 126 – 139 (2006).

    Article  Google Scholar 

  7. S. N. Lezhnev, I. E. Volokitina, and A. V. Volokitin, “Evolution of microstructure and mechanical properties of steel during pressing-drawing,” Phys. Met. Metallogr., 118(11), 1167 – 1170 (2017).

    Article  CAS  Google Scholar 

  8. A. I. Rudskoy, A. A. Bogatov, D. Sh. Nukhov, and A. O. Tolkushkin, “A new method of severe plastic deformation of metals,” Metalloved. Term. Obrab. Met., No. 1, 1 – 5 (2018).

    Google Scholar 

  9. S. Lezhnev, E. Panin, and I. Volokitina, “Research of combined process rolling-pressing influence on the microstructure and mechanical properties of aluminium,” Adv. Mater. Res., 814, 68 – 75 (2013).

    Article  Google Scholar 

  10. A. V. Filippov, S. Yu. Tarasov, O. A. Podgornykh, et al., “Effect of annealing on the deformation behavior of fine-grained brass under scratching,” in: Mater. Int. Conf. “Promising Materials with Hierarchic Structure for New Technologies and Reliable Structures” [in Russian] (2018), pp. 115 – 144.

  11. I. Volokitina, S. Lezhnev, E. Orlova, and G. Kurapov, “Research of the microstructure and mechanical properties of copper and CuZn36 developing during deformation into the equal channel speed matrix with high-intensity cooling,” Key Eng. Mater., 684, 346 – 352 (2016).

    Article  Google Scholar 

  12. S. Qu, X. H. An, H. J. Yang, et al., “Microstructural evolution and mechanical properties of Cu – Al alloys subjected to equal channel angular pressing,” Acta Mater., 5, 1586 – 1601 (2009).

    Article  Google Scholar 

  13. A. A. Gazder, Torre F. Dalla, C. F. Gu, et al., “Microstructure and texture evolution of bcc and fcc metals subjected to equal channel angular extrusion,” Mater. Sci. Eng., 415, 126 – 139 (2006).

    Article  Google Scholar 

  14. Y. Ywahashi, Z. Horita. M. L. Nemoto, and T. G. Langdon, “An investigation of microstructural evolution during equal-channel angular pressing,” Acta Mater., 45, 4733 – 4742 (1997).

    Article  Google Scholar 

  15. A. V. Nayzabekov, S. N. Lezhnev, and I. E. Volokitina, “Change in copper microstructure and mechanical properties with deformation in an equal channel stepped die,” Metal. Sci. Heat Treat., 57(5 – 6), 254 – 260 (2015).

    Article  Google Scholar 

  16. M. A. Filippov, V. R. Baraz, and M. A. Gervas’ev, Methodology for Choosing Metallic Alloys and Hardening Processes in Machine Building, Vol. 2 [in Russian], Izd. Ural. Univers., Ekaterinburg (2013), 326 p.

  17. Yu. A. Geller and A. G. Rakhshtadt, The Science of Materials [in Russian], Metallurgiya, Moscow (1989), 456 p.

Download references

Author information

Authors and Affiliations

  1. Karaganda State Industrial University, Temirtau, Kazakhstan

    I. E. Volokitina

Authors
  1. I. E. Volokitina
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to I. E. Volokitina.

Additional information

Translated from Metallovedenie i Termicheskaya Obrabotka Metallov, No. 3, pp. 51 – 54, March, 2021.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Volokitina, I.E. Effect of Preliminary Heat Treatment on Deformation of Brass by the Method of ECAP. Met Sci Heat Treat 63, 163–167 (2021). https://doi.org/10.1007/s11041-021-00664-y

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11041-021-00664-y

Key words

Search

Navigation