Polylactide (PLA)/flax mat and modified PLA/flax mat composites were produced by the hot pressing technique. The dispersion of the flax mat in the composites was studied by the scanning electron microscopy (SEM). The PLA composites were subjected to an instrumented falling-weight impact test. The mechanical and thermal properties of the composites were determined by using tensile tests, a thermogravimetric analysis (TGA), and a dynamic-mechanical thermal analysis (DMTA). It was found that the flat mat increased the impact resistance of PLA, but the tensile strength of the modified PLA/flax mat composite decreased slightly compared with that of PLA. Data on the elongation at break pointed to a higher ductility of the modified PLA and its composites. Moreover, the addition of a thermal modifier enhanced the thermal resistance below the processing temperature of PLA and had a marginal effect on its glass-transition temperature. The master curves of the storage modulus were constructed by employing the time-temperature superposition (TTS) principle. The principle of a linear viscoelastic material was fairly applicable to transition from the modulus to the creep compliance for all the systems studied.
Similar content being viewed by others
References
S. Vainionpaa, P. Rokkanen, and P. Torrmala, “Surgical applications of biodegradable polymers in human tissues,” Prog. Polym. Sci., 14, 679-716 (1989).
M. J. Manninen, U. Päivärinta, H. Pätiälä, P. Rokkanen, R.Taurio, M. Tamminmäki, and P. Törmälä, “Shear strength of cancellous bone after osteotomy fixed with absorbable self-reinforced polyglycolic acid and poly-L-lactic acid rods,” J. Mater. Sci., 3, 245-251 (1992).
R. Auras, B. Harte, and S. Selke, “An overview of polylactides as packaging materials,” Macromol. Biosci., 4, 835-864 (2004).
R. Dangtungee, K. Petcharoen, K. Pinijsattawong, and S. Siengchin, “Investigation of the rheological properties and die swell of polylactic acid/nanoclay composites in a capillary rheometer,” Mech. Compos. Mater., 47, No. 6, 663-670 (2012).
E. Fortunati, I. Armentano, A. Iannoni, and J.M. Kenny, “Development and thermal behavior of ternary PLA matrix composites,” Polymer Degradation and Stability, 95, 2200-2206 (2010).
R. Kumar, M. K. Yakabu, and R. D. Anandjiwala, “Effect of montmorillonite clay on flax fabric reinforced poly lactic acid composites with amphiphilic additives,” Composites: Part A, 41, 1620-1627 (2010).
N. Graupner, A. S. Herrmann, and J. Müssig, “Natural and man-made cellulose fibre-reinforced poly(lactic acid) (PLA) composites: An overview about mechanical characteristics and application areas,” Composites: Part A, 40, 810-821 (2009).
S. Ochi, “Mechanical properties of kenaf fibers and kenaf/PLA composites,” Mechanics of Materials, 40, 446-452 (2008).
A. K. Bledzki, A. Jaszkiewicz, and D. Scherzer, “Mechanical properties of PLA composites with man-made cellulose and abaca fibres,” Composites: Part A, 40, 404-412 (2009).
F. Roussièr, C. Baley, G. Godard, and D. Burr, “Compressive and tensile behaviours of PLLA matrix composites reinforced with randomly dispersed flax fibres,” Appl. Compos. Mater., 19, 171-188 (2012).
S. Siengchin, T. Pohl, L. Medina, and P. Mitschang, “Structure and properties of flax/polylactide/alumina nanocomposites,” J. Reinf. Plast. Compos., 32, 23–33.
B. Bax and J. Müssig, “Impact and tensile properties of PLA/Cordenka and PLA/flax composites,” Compos. Sci. Technol., 68, 1601-1607 (2008).
K. Das, D. Ray, I. Banerjee, N. R. Bandyopadhyay, S. Sengupt, A.K. Mohanty, and M. Misra, “Crystalline morphology of PLA/clay nanocomposite films and its correlation with other properties,” J. Appl. Polym. Sci., 118, 143-151 (2010).
D. R. Mulinari, H. J. C. Voorwald, M. O. H. Cioffi, M. L. C. P. Silva, T. G. Cruz, and C. Saron, “Sugarcane bagasse cellulose/HDPE composites obtained by extrusion,” Compos. Sci. Technol., 69, 214-219 (2009).
A. Gomes, T. Matsuo, K. Goda, and J. Ohgi, Development and effect of alkali treatment on tensile properties of curaua fiber green composites,” Composites A, 38, 1811-1820 (2007).
A. Arbelaiz, G. Cantero, B. Fernández, I. Mondragon, P. Ganán, and J. M. Kenny, “Flax fiber surface modifications: Effects on fiber physico-mechanical and flax/polypropylene interface properties,” Polymer Composites, 26, 324-332 (2005).
M. Kowalczyk, E. Piorkowska, P. Kulpinski, and M. Pracella, “Mechanical and thermal properties of PLA composites with cellulose nanofibers and standard-size fibers,” Composites: Part A, 42, 1509-1514 (2011).
S. Mohanty, S.K. Verma, and S. K. Nayak, “Dynamic mechanical and thermal properties of MAPE treated jute/HDPE composites,” Compos. Sci. Technol., 66, 538-547 (2006).
M. T. Shaw and W. J. MacKnight, Introduction to Polymer Viscoelasticity, John Wiley and Sons, NY (2005).
S. Siengchin, Ph.D. Dissertation, IVW Schriftenreihe Band 82, A.K. Schlarb (Hrsg.), Kaiserslautern (2008).
L. Suryanegara and A. N. Nakagaito, and H. Yano, “The effect of crystallization of PLA on the thermal and mechanical properties of microfibrillated cellulose-reinforced PLA composites,” Compos. Sci .Technol., 69, 1187-1192 (2009).
S. Siengchin, J. Karger-Kocsis, and R. Thomann, “Alumina-filled polystyrene micro- and nanocomposites prepared by melt mixing with and without latex precompounding: Structure and properties,” J. Appl. Polym. Sci., 105, 2963-2972 (2007).
J. D. Ferry, Viscoelastic Properties of Polymers, Wiley and Sons, NY (1980).
Author information
Authors and Affiliations
Corresponding author
Additional information
Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 50, No. 2, pp. 361-372 , March-April, 2014.
Rights and permissions
About this article
Cite this article
Siengchin, S. Reinforced Flax Mat/Modified Polylactide (PLA) Composites: Impact, Thermal, and Mechanical Properties. Mech Compos Mater 50, 257–266 (2014). https://doi.org/10.1007/s11029-014-9412-4
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11029-014-9412-4