Skip to main content
SpringerLink
Log in

Effect of Temperature-Deformation Treatment Regime for Special Alloy Steels on Rolled Product Structural State and Properties

  • Published:
Metallurgist Aims and scope

The effect of cooling regime after rolling and also subsequent spheroidizing annealing are studied for rolled product of special alloy steel 40Kh of an industrial melt on metal structural state and amount of relative reduction of area. It is established that the amount of reduction of area, varying uniformly round rolled product capacity for cold upsetting, increases with a reduction in the proportion of ferrite and an increase in steel ferrite-pearlite structure uniformity and fineness. The most favorable microstructure and high value for reduction of area occur after spheroidizing annealing of rolled product with a bainitic structure.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.

Similar content being viewed by others

References

  1. A. B. Stepanov, N. A. Arutyunyan, Yu. I. Ivin, and A. I. Zaitsev, “Effect of microstructure and surface defects on the capacity of special alloy steel round bar for cold upsetting,” Metallurgist, 60, No. 7, 713–720 (2016).

    Article  Google Scholar 

  2. A. I. Zaitsev, A. V. Knyazev, A. V. Amezhnov, et al., “Effect of nonmetallic inclusions and impurities on properties specifying the properties of round rolled product of special alloy steels,” Metallurg. No. 8, 65–74 (2017).

  3. M. V. Li et al., “A computational model for the prediction of steel hardenability,” Metallurg. Mater. Trans. B, 29, No. 3, 661–672 (1998).

    Article  Google Scholar 

  4. A. Timoshenkov et al., “Influence of deformation on phase transformation and precipitation of steels for oil country tubular goods,” Steel Res. Int., 85, No. 6, 954–967 (2014).

    Article  Google Scholar 

  5. A. P. Gulyaev, Materials Science, Metallurgiya, Moscow (1977).

    Google Scholar 

  6. E. A. Dudov, “Ways of improving the quality of 20G2R rolled product for cold forging,” Proizv. Prokata, No. 5, 17–19 (2001).

  7. G. A. Navrotskii (ed.), Cold Forging, Mashinostroenie, Moscow (1973).

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Bardin Central Research Institute of Ferrous Metallurgy (TsNIIchermet), Moscow, Russia

    A. V. Koldaev, A. V. Amezhnov, A. I. Zaitsev & A. B. Stepanov

  2. Chemical Faculty, Lomonosov Moscow State University, Moscow, Russia

    A. I. Zaitsev

Authors
  1. A. V. Koldaev
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. A. V. Amezhnov
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. I. Zaitsev
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. A. B. Stepanov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to A. V. Koldaev.

Additional information

Translated from Metallurg, No. 10, pp. 30–34, October, 2017.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Koldaev, A.V., Amezhnov, A.V., Zaitsev, A.I. et al. Effect of Temperature-Deformation Treatment Regime for Special Alloy Steels on Rolled Product Structural State and Properties. Metallurgist 61, 858–862 (2018). https://doi.org/10.1007/s11015-018-0576-3

Download citation

  • Received:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11015-018-0576-3

Keywords

Search

Navigation