Abstract
In order to distinguish between shallow earthquakes and quarrying activity, we evaluated 3069 seismic signals from 413 occurrences (112 explosions and 301 shallow earthquakes, depths 5 km), collected by the Aswan seismic sub-network in southern Egypt from 2010 to 2021. The spectral properties and related source parameters (e.g., seismic moment and corner frequency) using the estimated P-wave source spectra for both earthquakes and quarry blasts were investigated. The analysis showed that the P-wave source spectra of shallow earthquakes have higher corner frequencies (8.8–23 Hz) than quarry blasts (1.0–2.6 Hz) within the same magnitude range. The source spectra of quarry blasts exhibited significant misfits with the omega-square model and had steeper falloffs at high frequencies. The selected quarry blasts have a narrow seismic moment range, from 2.03 × 1011 to 1.35 × 1012 Nm. Our results demonstrate that the evaluation of misfit of P-wave spectra from the omega-square source model, based on spectral amplitude characteristics of high- and low-frequency bands, is the most reliable discriminant method in the routine data analysis of the target area.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
The Aswan High Dam region in southwestern Egypt is located on the African Plate within the Nubian Shield craton. Most of the active faults in western Aswan that are related to the Western Desert fault system are oriented east–west and few faults are north–south oriented (Fig. 1a). The east–west faults are located adjacent to the Sinn El Kaddab plateau and are relatively long, extending to the Nubia plain; some extend more than 200 km (Issawi 1973; Issawi 1978; Woodward-Clyde Consultants 1985; Hamimi et al. 2018). The most active faults are distributed in the Kalabsha fault zone (Hamimi et al. 2018), and the largest was the magnitude 5.6 earthquake of November 14, 1981. Former studies in Aswan have shown that seismic activity is concentrated along the active faults and increases near the intersection of north–south and east–west faults (Fig. 1b). Most earthquakes have a strike-slip focal mechanism, while normal fault motion is rarely observed (e.g., El-Amin 2003; Abou-Elenean 2003; Hassib et.al 2010; Hussein et al. 2013; Hosny et al. 2014; Badreldin et al. 2019; Saadalla et al. 2020; Mostafa and Mohamed 2021).
The cement industry in Egypt is growing rapidly in Aswan since limestone, the primary raw material for cement, is mined in the Sin el-Khadab plateau. The blasting of many quarries in the area has yielded 70% of the limestone used in the cement industry. The quarrying activity has been recorded by the local Aswan seismic sub-network, operated by the National Egyptian Seismic Network (ENSN). The anthropogenic activity decreases the reliability of the earthquake catalog in the target region, which leads to incorrect earthquake hazard and risk analysis. Additionally, these quarry blasts are carried out in an area with high seismic activity and complex tectonic setting. The explosions may trigger earthquakes in the nearby faults and disturb the stress pattern of existing tectonic structures (Fat-Helbary et al. 2012). Quarry blasting near the seismically active areas has fostered the interest of researchers to identify the characteristics of seismic and quarry activity in the Aswan region.
Discrimination of anthropogenic activities from natural earthquakes is done using simple procedures such as explosion location, times of occurrence, and satellite images. However, the methods may not be robust and not be reliable for explosions occurring in active fault zones (Wiemer and Baer 2000; Horasan et al. 2009). The discrimination can also be achieved by applying waveform-based approaches, including spectral modulation (e.g., Taylor et al. 1988; Kim et al. 1994; Walter et al. 1995), amplitude ratios among seismic phases (e.g., Bennett and Murphy 1986; Wuester 1993; Plafcan et al. 1997; McLaughlin et al. 2004; Morozov 2008, Anderson et al. 2009; Dahy and Hassib 2010), coda wave analysis (Su et al. 1991; Hartse et al. 1995), ripple-fire spectral modulation schemes (e.g., Hedlin et al. 1990; Smith 1993; Carr and Garbin 1998; Arrowsmith et al. 2006, 2007), and other procedures (Musil and Plesinger 1996; Parolai et al. 2002; Tibuleac et al. 2004).
This study aims to differentiate the characteristics of quarry blasts from earthquakes in Aswan. We investigated the spectral properties of ripple-firing quarry blasts and earthquakes in the southwestern part of Aswan, Southern Egypt, to quantify the differences in spectral characteristics between natural earthquakes and blasts. This discrimination helps to provide a reliable seismic catalog containing only earthquakes in the study area, which can evaluate the seismicity of seismic zones in and around Aswan.
2 Data
The Aswan seismic sub-network, operated by the Aswan Regional Seismological Research Centre of the National Research Institute of Astronomy and Geophysics (NRIAG), consists of 15 broadband seismic stations. The seismometers installed in the network are Trillium 40 and Trillium-120QA (Nanometrics Inc.), and the data were recorded with a sampling frequency of 100 Hz. We processed 3069 signals from 301 shallow earthquakes (< 5 km depth) and 112 quarry blasts recorded by the sub-network in southern Egypt from January 2010 to December 2021. Since the objective of this study is to investigate the differences between blasting and earthquakes, we obtained information regarding the date and time of blasting in the target period from the cement company in advance. Figure 2a shows the distribution of epicenters of the selected dataset. The selected earthquakes and quarry blasts have the same magnitude range (1.5 < Ml ≤ 3) (Fig. 2b). Figure 2c shows the number of earthquakes and quarry blasts recorded at each seismic station. Table S1 of the supplementary materials lists the original parameters of the selected events. We selected waveform data based on the conditions that (a) the seismic event was recorded at more than four stations (Fig. 2c), and (b) waveforms were unclipped with high signal-to-noise ratios (S/N). Figure 3a and b show an example of the recorded data for an earthquake on October 22, 2017, and for quarry blasts on February 11, 2018, respectively. The waveforms of the observed quarry blast show trailing phases in addition to the initial P-waves, which makes the discrimination difficult. Waveform data selected are pre-processed using seismic analysis code software (Goldstein and Snoke 2005).
2.1 Spectral decomposition method
The waveforms of shallow earthquakes and quarry blasts to derive the P-wave source spectra were extracted and the displacement spectra over a 1.28-s window for noise and signal before and after the P-wave arrivals and ensured acceptable signal to noise ratio (S/N) for all spectra used in the analysis was computed (see an example in Fig. 4). The signal to noise amplitude ratio exceeds 10 in the frequency range between 0.8 and 50 Hz for all events are used in this study. A Parzen window of 5.0-Hz duration was applied to smooth the obtained spectra. The obtained P-wave displacement spectra are a superposition of the different effects and responses (source, path, and site effects),
where Oij (f) is the observed spectra from source i at receiver j, Si (f) is the source effect, Gj (f) is the site response, and Pij (f) represents seismic wave attenuation along the path. The next step is to process the spectra to remove the path and site effects from the observed spectra. Equation (1) is a linear system of equations with an overdetermined problem, resulting in a trade-off between the source and site results. This shortage is solved numerically using a robust iterative least square analysis using a reference site.
The reference site is a rigid rock site with no amplification compared to other receiver sites. However, many studies in other regions pointed out that finding such a site is difficult (Steidl et al. 1996; Archuleta 1998). Other researchers assumed that the amplification at the possible reference station site is around 2.0 due to the free surface effect (e.g., Iwata and Irikura 1988; Takemura et al. 1991; Kato et al. 1992). The significant disadvantage of referencing a rock site is that the number of processed events is limited to the number of events recorded by the selected reference site. Saadalla et al. (2020, 2019) pointed out that station New Gabal Marwa (NGMR), which belongs to the Aswan seismic sub-network, has a uniform amplification curve around 2.0. The station can be used as a suitable reference site in the inversion analysis.
The data selection procedure, data preparation, and spectral inversion analysis assume reference sites are applied with the same weights, conditions, and constraints for both families of earthquakes and quarry blasts of the dataset. The spectral analysis follows Andrews (1986) and Iwata and Irikura (1988). The inversion finally yields the site terms except for the reference site and anelastic attenuation factor of the area. These factors are introduced into Eq. (1) to obtain the source spectra for all events at all observation sites. We regard the average source spectra of all available stations derived for each event as the source spectrum for the individual event.
2.2 Source parameter estimations
We obtained theoretical P-wave source spectra for earthquakes and quarry blast based on the omega-square source formula proposed by Brune (1970). Brune’s model relates seismic moment to the displacement source spectra as
The seismic moment M0 is calculated from the flat-level P-wave displacement spectra Ω0. Here, ρ is the density, v is the P-wave velocity at the source, F is the free surface effect, Rθφ is the P-wave radiation pattern, and G(r,h) is the geometrical spreading effect. Radiation patterns were used for correction using 0.52 for the P-wave (Aki and Richards 2002). We obtained values of ρ and v from the 1D seismic velocity model of Khalil et al. (2004) (Table 1). The corner frequency fc of each event is estimated by finding the intersection between the low- and high-frequency asymptotes of the obtained displacement source spectra (Baumbach and Borman 2012; Kiratzi and Louvari 2001; Ashkpour Motolagh and Mostafazadeh 2008; Havskov and Ottemoeller 2010). Andrews (1986) proposed a method to determine fc from the flat displacement spectrum edis (f) at the low frequency and the flat level of the acceleration spectra eacc (f) at the high frequency as described in Eqs. (3), (4), and (5).
where A0 is the flat level of the acceleration spectra. The obtained seismic moment for each event is used to calculate the moment magnitude using the formula of Kanamori (1977),
3 Results and discussions
Figure 5a shows an example of the average source spectra and standard deviation of the earthquake that occurred on October 22, 2017, at 11:20 (GMT), and Fig. 5b shows an example of the average source spectra of the explosion on February 11, 2018, at 06:32 (GMT) with the standard deviations. The obtained spectra slightly vary among observation points, implying that the inversion errors and scattering effects caused by different azimuths of the receivers are small. We calculated corner frequencies and seismic moment values for each event based on Eqs. 3–6 to discriminate between natural earthquakes and artificial events. Figure 6a and b show that the obtained displacement source spectra for quarry blasts show steeper falloffs at high frequencies in comparison with earthquakes. We found that the displacement P-wave source spectra of the earthquakes show suitable fittings with the omega-square models, where the quarry blasts indicate large misfits. Figure 7a and b show the fitting results with the omega-square models for different-size earthquakes and quarry blasts, respectively. Additionally, the quarry blasts exhibited steeper falloffs at high frequencies than earthquakes, which led to lower stress drops and corner frequencies. The deficiency of quarry blasts from high-frequency seismic energy was attributed to the ripple firing mechanism of the quarry explosions (e.g., Allmann et al. 2008; Shearer and Allmann 2007; Su et al. 1991; Bennett and Murphy 1986; Taylor et al. 1988).
Figure 8 shows the corner frequencies of the earthquakes and quarrying of the same magnitude ranged between 8.8–23 Hz and 1.0–2.6 Hz, respectively. We obtained the seismic moment values are in the range 2.03 × 1011–1.35 × 1012 Nm for quarry blasts and 1.02 × 1010 to 5.83 × 1012 for natural earthquakes, respectively. Quarry blasting has a narrower seismic moment range than shallow earthquakes in the Aswan region (Table S2, supplementary material).
We finally discuss the discrimination method between earthquakes and quarry blasts. The classification between explosion events and earthquakes is usually done in a simple manner based on the epicenter location, epicenter depth, or the complexity of the waveform. However, the locations and depths between quarry blasts and earthquakes are similar, and the waveforms-based classification is not easy because of the presence of later phases in both waveforms (Fig. 3). We attempted to identify earthquakes and explosions using different magnitude scales; Ml was obtained from the earthquake catalog, and Mw was derived from this study. Figure 9 shows the relationship between Ml and Mw for both earthquakes and quarry blasts. The relationship derived from earthquakes is Mw = 0.7 Ml + 0.4, while Mw = 0.6 Ml + 0.9 for quarry blasts, indicating that the discrimination using the Mw- Ml relationship is not realistic. Our results suggest that only the spectral properties and source parameters could be used as reliable and robust discriminant factors. The most applicable method is deriving the source spectrum from the observed P-wave by removing the path and site characteristics obtained in this study and evaluate the agreement with the omega-square model. Alternatively, using the ratio of the amplitudes in the low-frequency component (< 10 Hz) to those in the high-frequency component (> 20 Hz) from the P-wave spectra of the observed waveforms as an indicator may enable the identification.
4 Conclusions
A total of 3069 seismic records were analyzed from 112 quarry blasts and 301 earthquakes with local magnitudes (Ml) between 1.7 and 3.1 from 2010 to 2021. The obtained P-wave displacement spectra from local shallow earthquakes and quarry blasts revealed various spectral properties and parameters (corner frequency and seismic moment) between both types of events. The Fourier spectra of quarry blasts poorly fit the omega-square source model and have lower fc than shallow earthquakes. The P-spectra for the quarry blasts have steeper falloffs and attenuated rapidly at a lower frequency in comparison with shallow earthquakes in the same tectonic region and within the same magnitude range. The investigated quarry blasts had longer source time durations of blasts than natural earthquakes, leading to lower corner frequencies and low-stress drop values than the studied natural seismic events. Our study focused on Aswan shallow earthquakes and quarry blasts, but we expect the obtained discriminant parameters and insights found in this analysis will be applicable to other regions of more direct interest to mining and quarrying. The spectral properties obtained in this study are helpful in event discrimination processing. Making a catalog of quarry blasting will be essential to evaluate the hazards and environmental impacts of the mining development in Egypt.
Data availability
The data that support the findings of this study are available from NRIAG but restrictions apply to the availability of these data, which were used under license for the current study, and so are not publicly available. Data are however available from the authors upon reasonable request and with permission of NRIAG.
Abbreviations
- NRIAG:
-
National Research Institute of Astronomy and Geophysics;
- NGMR:
-
New Gabal Marwa;
- \({f}_{\mathrm{c}}\) :
-
Corner frequency;
- \({M}_{0}\) :
-
Seismic moment;
- \({M}_{\mathrm{w}}\) :
-
Moment magnitude;
- Ml:
-
Local magnitude;
- \({\Omega }_{0}\) :
-
Long period amplitude;
- \(log {M}_{o}\) :
-
Logarithm seismic moment;
- \({V}_{P}\) :
-
P-wave velocity;
- \({V}_{S}\) :
-
S-wave velocity;
- \(Rho\) :
-
Density
References
Abou-Elenean KM (2003) Focal mechanism and stress tensor inversion of earthquakes at and around Nasser Lake, Egypt. Bull Fac Sci Zagazig Univ 25:77–107
Aki K, Richards PG (2002) Quantitative seismology (1).
Allmann BP, Shearer PM, Hauksson E (2008) Spectral discrimination between quarry blasts and earthquakes in southern California. Bull Seis Soc Am 98:2073–2079
Anderson DN, Walre WR, Fagan DK, Mercier TM, Taylor SR (2009) Regional multi station discriminants: magnitude, distance, and amplitude corrections, and sources of error. BullSeis Soc Am 99(2A):794–808
Andrews DJ (1986) Objective determination of source parameters and similarity of earthquakes of different size. Earthquake source mechanics, 259–267.
Archuleta RJ (1998). ESG studies in the United States: results from borehole arrays. In Proceedings of the Second International Symposium of the Effects of Surface Geology on Seismic Motion, 1998 (pp. 3–14).
Arrowsmith SJ, Arrowsmith MD, Hedlin MAH, Stump B (2006) Discrimination of delay-fired mine blasts in Wyoming using an automatic time-frequency discriminant. Bull Seis Soc Am 96(6):2368–2382
Arrowsmith SJ, Hedlin MAH, Arrowsmith MD, Stump B (2007) Identification of delay-fired mining explosions using seismic arrays: application to the PDAR array in Wyoming, USA. Bull Seis Soc Am 97(3):989–1001
AshkpourMotolagh S, Mostafazadeh M (2008) Source parameters of the Mw 5.8 Fin (south of Iran) earthquake of March 25, 2006. World Appl Sci J 4:104–115
Badreldin H, Abdel-aal AK, Toni M, El-Faragawy K (2019) Moment tensor inversion of small-to-moderate size local earthquakes in Egypt. J Afr Earth Sc 151:153–172
Baumbach M, Borman P (2012) Determination of source parameters from seismic spectra. New Manual of Seismological Observatory practice 2 (NMSOP-2) (pp. 1–7). Deutsches Geo Forschugs Zentrum GFZ, Potsdam.
Bennett TJ, Murphy JR (1986a) Analysis of seismic discrimination capabilities using regional data from western United States events. Bull Seismol Soc Am 76(4):1069–1086
Brune JN (1970) Tectonic stress and the spectra of seismic shear waves from earthquakes. J Geophys Res 75(26):4997–5009
Carr DB, Garbin HD (1998) Discriminating ripple-fired explosions with high-frequency (>16 Hz) data. Bull Seis Soc Am 88(4):963–972
Dahy SA, Hassib GH (2010) Spectral discrimination between quarry blasts and microearthquakes in Southern Egypt. ResJEarth-Sci 2:01–07
Egyptian Geological Survey and Mining Authority (1981). Geologic map of Egypt: EGSMA, Ministry of Industry and Mineral Resources, Cairo, SCALE 1:2,000,000.
El-Amin MM (2003) Inversion of seismograms to determine the moment tensor components and source time functions for sources of some earthquakes (occurred in Kalabsha area west of Nasser Lake, Egypt) using back projection technique. Ph. D. Thesis, Ain-Shams Univ. Cairo, Egypt: 236.
Fat-Helbary RE, Abdelrahman K, Fnais MS, Abdelmoneim E (2012) Seismic hazard and site response assessment on the proposed site of Aswan Cement Plant. Egypt Int J Earth Sci 5(4):644–651
Goldstein P, Snoke A (2005) SAC Availability for the IRIS Community. VII, and No, Incorporated Institutions for Seismology Data Management Center Electronic Newsletter, Vol, p 1
Hamimi Z, Haggag W, Osman R, El-Bialy M, El-Nadr IA, Fadel M (2018) The active Kalabsha Fault Zone in Southern Egypt: detecting faulting activity using field-structural data and EMR-technique, and implications for seismic hazard assessment. Arab J Geosci 11(15):421
Hartse HE, Phillips WS, Fehler MC, House LS (1995) Single station spectral discrimination using coda waves. Bull Seis Soc Am 85(5):1464–1474
Hassib G, Hamed H, Dahy S, Hassoup A, Moustafa S (2010) Detection of the seismic quiescence along the seismic active faults in Kalabsha area, west of Lake Nasser, Aswan. Egypt Acta Geodaetica Et Geophysica Hungarian 45(2):210–226
Havskov J, Ottemoeller L (2010) Routine data processing in earthquake seismology. Springer, Dordrecht, 347. https://doi.org/10.1007/978-90-481-8697-6
Hedlin MA, Minster JB, Orcutt JA (1990) An automatic means to discriminate between earthquakes and quarry blasts. Bull Seis Soc Am 80(6B):2143–2160
Horasan G, Boztepe-Güney A, Küsmezer A, Bekler F, Öğütçü Z, Musaoğlu N (2009) Contamination of seismicity catalogues by quarry blasts: an example from Istanbul and its vicinity, north-western Turkey. J Asian Earth Sci 34:90–99
Hosny A, Ali SM, Abed A (2014) Study of the 26 December 2011 Aswan earthquake, Aswan area, south of Egypt. Arab J Geosci 7(11):4553–4562
Hussein HM, Elenean KA, Marzouk IA, Korrat IM, El-Nader IA, Ghazala H, ElGabry MN (2013) Present-day tectonic stress regime in Egypt and surrounding area based on inversion of earthquake focal mechanisms. J Afr Earth Sc 81:1–15
Issawi B (1973) Nubia sandstone: Type Section: GEOLOGICAL NOTES. AAPG Bull 57(4):741–745
Issawi BT (1978) Geology of Nubia west area, western desert. Ann Geol Surv Egypt 3:237–253
Iwata T, Irikura K (1988) Source parameters of the 1983 Japan Sea earthquake sequence. J Phys Earth 36(4):155–184
Kanamori H (1977) the energy release in great earthquakes. J Geophys Res 82:2981–2987
Kato K, Takemura M, Ikeura T, Urao K, Uetake T (1992) Preliminary analysis for evaluation of local site effects from strong motion spectra by an inversion method. J Phys Earth 40(1):175–191
Khalil AE, El-Hady SM, Hosny A (2004) Three-dimensional velocity structure of VP and VP/VS around Aswan area. Egypt J Appl Geophys 3(1):301–314
Kim WY, Simpson DW, Richards PG (1994) High-frequency spectra of regional phases from earthquakes and chemical explosions. Bull Seismol Soc Am 84:1365–1386
Kiratzi A, Louvari E (2001) Source parameters of the Izmit-Bolu 1999 (Turkey) earthquake sequences from teleseismic data. Ann Geofis 44:33–47
McLaughlin KL, Bonner JL, Barker R (2004) Seismic source mechanisms for quarry blasts: modelling observed Rayleigh and Love wave radiation patterns from a Texas quarry. Geophys J Int 156:79–93
Morozov AN (2008) Method of identification of explosive seismicity on territories of the Arkhangelsk region. Institute of Ecological Problem in the North of UB RAS, Arkhangelsk
Mostafa SI, Mohamed AEEA (2021) Seismotectonic studies in Aswan area. Egypt Arab J Geosci 14(21):1–16
Motlagh SA, Mostafazadeh M (2008) Source parameters of the Mw 5.8 fin (South of Iran) earthquake of March 25 2006. World Appl Sci J 4(1):104–115
Musil M, Plesinger A (1996) Discrimination between local microearthquakes and quarry blasts by multi-layer perceptrons and Kohonen maps. Bull Seismol Soc Am 86:1077–1090
Parolai SL, Trojani M, Frapiccini MG (2002) Seismic source classification by means of a sonogram-correlation approach: application to data of the RSM Seismic Network (central Italy), Pure Appl. Geophys 159:2763–2788
Plafcan D, Sandvol E, Seber D, Barazangi M, Ibenbrahim A, Cherkaoui TE (1997) Regional discrimination of chemical explosions and earthquakes: a case study in Morocco. Bull Seismol Soc Am 87(5):1126–1139
Saadalla H, Abd el-aal AK, Abdelnasser M, El-Faragawy K (2019) Determination of earthquake source parameters using the inversion of waveform data: a case of small earthquakes around High Dam Lake, Aswan region. Egypt J Afr Earth Sci 151:403–416
Saadalla H, Abd el–aal AK, Mohamed A, El-Faragawy K (2020) Characteristics of earthquakes recorded around the High Dam Lake with comparison to natural earthquakes using waveform inversion and source spectra. Pure Appl Geophys. https://doi.org/10.1007/s00024-020-02490-4
Shearer PM, Allmann BP (2007) Spectral studies of shallow earthquakes and explosions in Southern California. Proceedings of the 29th Monitoring Research Review: Ground-Based Nuclear Explosion Monitoring Technologies, 656–662.
Smith AT (1993) Discrimination of explosions from simultaneous mining blasts. Bull Seis Soc Am 83:160–179
Steidl JH, Tumarkin AG, Archuleta RJ (1996) What is a reference site? Bull Seismol Soc Am 86(6):1733–1748
Su F, Aki K, Biswas NN (1991) Discriminating quarry blasts from earthquakes using coda waves. Bull Seismol Soc Am 81(1):162–178
Takemura M, Kato K, Ikeura T, Shima E (1991) Site amplification of S-waves from strong motion records in special relation to surface geology. J Phys Earth 39(3):537–552
Taylor SR, Sherman NW, Denny MD (1988) Spectral discrimination between NTS explosions and western United States earthquakes at regional distances. Bull Seismol Soc Am 78(4):1563–1579
Tibuleac IM, Britton J, Harris DB, Hauk T, Hooper H, Bonner JL (2004) Detection methods for mining explosions in southern Asia, 26th Seismic Research Review, 427–438.
Walter WR, Mayeda KM, Patton HJ (1995) Phase and spectral ratio discrimination between NTS earthquakes and explosions, part I: Empirical observations. Bull Seism Soc Am 85:1050–1067
Wiemer S, Baer M (2000) Mapping and removing quarry blast events from seismicity catalogues. Byzeull Seismol Soc Am 90(2):525–530
Woodward-Clyde Consultants (1985) Earthquake activity and dam stability evaluations for the Aswan High Dam, Egypt, vol. 3: Seismic Geology and Tectonic Studies of the Aswan Region, report to High Aswan Dam Authority, Ministry of Irrigation, A.R.E., under Contract No. 263–0102-c-00-HADA-00,USAID Project No.,263–0042–305pp.
Wuester J (1993) Discrimination of chemical explosions and earthquakes in central Europe- a case study. Bull Seismol Soc Am 83:1184–1212
Acknowledgements
Our profound gratitude goes to Aswan Regional Earthquakes Research Centre, Seismology Lab, Seismology Department (NRIAG), for providing us with the data used in this study. We offer our profound thanks for the financial support from the Quarries Services project working under the Seismology Department of the National Research Institute of Astronomy and Geophysics.
Funding
Open access funding provided by The Science, Technology & Innovation Funding Authority (STDF) in cooperation with The Egyptian Knowledge Bank (EKB). This study was supported by the Quarries Services project working under the Seismology Department of the National Research Institute of Astronomy and Geophysics (NRIAG).
Author information
Authors and Affiliations
Contributions
HS processed the earthquake and quarry blast data and performed spectral inversions. The computer program for spectral decomposition analysis was prepared by TH, and HM contributed to interpretations of the results. HS wrote the initial draft of the manuscript, and TH edited it. All the authors have read and approved the final manuscript.
Corresponding author
Ethics declarations
Ethics approval and consent to participate
Not applicable.
Consent for publication
Not applicable.
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Below is the link to the electronic supplementary material.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Saadalla, H., Abdelhafiez, H.E. & Hayashida, T. Discrimination between earthquakes and quarry blasts in the Aswan region, southern Egypt, using P-wave source spectra. J Seismol 27, 279–289 (2023). https://doi.org/10.1007/s10950-023-10143-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10950-023-10143-x