Abstract
Archaeological structures built across active faults and ruptured by earthquakes have been used as markers to measure the amount of displacement caused by ground motion and thus to estimate the magnitude of ancient earthquakes. The example used in this study is the Crusader fortress at Tel Ateret (Vadum Iacob) in the Jordan Gorge, north of the Sea of Galilee, a site which has been ruptured repeatedly since the Iron Age. We use detailed laser scans and discrete element models of the fortification walls to deduce the slip velocity during the earthquake. Further, we test whether the in-situ observed deformation pattern of the walls allows quantification of the amount both sides of the fault moved and whether post-seismic creep contributed to total displacement. The dynamic simulation of the reaction of the fortification wall to a variety of earthquake scenarios supports the hypothesis that the wall was ruptured by two earthquakes in 1202 and 1759 CE. For the first time, we can estimate the slip velocity during the earthquakes to 3 and 1 m/s for the two events, attribute the main motion to the Arabian plate with a mostly locked Sinai plate, and exclude significant creep contribution to the observed displacements of 1.25 and 0.5 m, respectively. Considering a minimum long-term slip rate at the site of 2.6 mm/year, there is a deficit of at least 1.6 m slip corresponding to a potential future magnitude 7.5 earthquake; if we assume ~5 mm/year geodetic rate, the deficit is even larger.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
Many archaeological sites in the Levant exhibit traces of earthquake damage. The affected buildings are commonly used to acquire information about the location, the time, and the local intensity of past earthquakes (e.g., Stiros and Jones 1996). However, retrieving information from archaeoseismic observations about the coseismic kinematics remains challenging and this is the goal of our research. It was not by chance that the term “archaeoseismological” was used for the first time in connection with earthquakes in the Levant. The Palestine Exploration Fund, founded in 1865, initiated surveys for the exploration of the Levant. In “The Survey of Western Palestine” from their expedition 1871–1878, Condor and Kitchner (1882) describe several archaeological sites in detail, of which numerous show damage now associated with seismic activity (Karcz and Kafri 1978). The earliest archaeological evidence for earthquake damage is reported by Alfonsi et al. (2012), who identify two Neolithic (7500–6000 BCE) earthquakes at Tell es-Sultan in the ancient city of Jericho, within the Dead Sea Fault (DSF) zone.
Information about palaeoseismic sources was obtained directly from archaeological structures that were bisected by fault ruptures. Examples from the DSF include Qasir el Telah (Niemi et al. 2001), Misyaf (Meghraoui et al. 2003), Tell Siçantarla (Altunel et al. 2009), and Tell Ateret (Marco et al. 1997; Ellenblum et al. 1998, 2015). The research at these sites focused on the earthquake history and estimates of the offset of the ruptured structures. In order to improve our knowledge of the properties of pre-instrumental earthquakes in this study, we further analyze the offset walls at Tell Ateret, located in the Jordan Gorge north of the Sea of Galilee (Fig. 1). Tell Ateret provides an opportunity to test whether, in addition to the measurement of the lateral displacement, it is also possible to deduce dynamic source parameters such as (a) the slip velocity of the fault during the earthquakes and (b) estimates of which side of the fault moved during an earthquake. Damaged structures at the site indicate the total relative slip at the site, however, which side moved and by which amount is not evident a priori. And (c) discriminate coseismic slip from possible pre- or post-seismic creep that contributed to the total displacement. Because the magnitude of the causing earthquake is mainly dependent on the offset and length of the ruptured fault segment, any creep contribution to the offset would result in overestimated magnitude. Therefore, determining the extent of potential creep would improve the knowledge base of the fault behaviour and thus contribute to future seismic hazard analysis.
This publication uses data collected within the framework of the PhD thesis “The Discrete Element Method in Archaeoseismological Research—Two Case Studies in Israel” of Gregor Schweppe published in 2019 at the faculty of mathematics and natural science of the University of Cologne.
2 Study area
The archaeological ruins of the Crusader fortress on Tell Ateret are 13 km north of the Sea of Galilee (SG), on the main trace of the DSF. The DSF is a left-lateral boundary fault between the Arabian plate and the Sinai subplate (Fig. 1). The entire fault system, which forms the tectonic pull-apart basins of Gulf of Aqaba (GoA), the Dead Sea, and the Hula Basin (HB), transfers the opening of the Red Sea to the Bitlis-Zagros collision zone (Quennell 1956; Freund 1965). The section between the GoA and the SG is mainly characterized by a single strike-slip fault, but in the Hula Basin, the fault splays into several non-parallel strands, the most prominent branches from east to west are the Rachaya Fault (RaF), Yammouneh Fault (YF), and the Roum Fault (RF) (see caption Fig. 1).
The DSF has been active since the Miocene (Bartov et al. 1980). The current seismicity is characterized by infrequent large earthquakes with periods of small to moderate earthquakes in between (Hamiel et al. 2009). The instrumental observation of the earthquakes of the Levant began in 1898 with the installation of the first seismological station (Helwan HLW) south of Cairo, Egypt. Since then the number of seismic stations and networks in the area increased. The catalogs of the larger networks in the region have been merged to a single catalog, which is continuously updated and can be accessed via http://seis.gii.co.il/ (last accessed 02.2020).
The pre-instrumental earthquakes in the area have been the subject of interdisciplinary research. The wealth of information from historical, geological, and archaeological archives were used to compile historical earthquake catalogs (Guidoboni and Comastri 2005; Sbeinati et al. 2005; Ambraseys 2009). Location and fault strands activated during the 1202 and 1759 earthquakes which affected Tell Ateret (Fig. 1) have been discussed in several papers (Marco et al. 1997, 2005; Ellenblum et al. 1998; Daëron et al. 2004, 2005, 2007; Nemer et al. 2008).
3 History of the Tell Ateret
The archaeological strata of the Tell Ateret include (early to late) an Iron Age II fortification, a Hellenistic complex with houses and fortifications, a medieval Crusader castle called Vadum Iacob (meaning Jacob’s Ford), and a Mamluk mosque. Vadum Iacob constitutes the most conspicuous remnant and includes a formidable 4.4 m wide defense wall and inner structures. The name (Latin: Vadum Iacob; Hebrew: Metzad Ateret; Arabic: Qasr al-'Atra) commemorates the legendary abode of the biblical Patriarch Jacob (Gen. 32:10) during the disappearance of his son Joseph (Ellenblum 2003). The most recent structure on the Tell is a Mamluk and Ottoman pilgrimage site with a mosque, which smoking paraphernalia determines its age of late Ottoman period.
During the Crusader period, after the victory of the battle of Montgisard in 1177, the Christian forces wanted to consolidate their power in the Muslim territory north of the SG. The purpose of the construction of the Crusader Fortress at Ateret in 1178 was to take control of the only crossing of the Jordan River between its source in the north and the SG. The crossing was part of an important trading route from Damascus to Acre (Ellenblum 2007). In 1179, the construction site was conquered by Saladin’s Muslim forces (Barber 1998; Ellenblum 1998, 2007). The unfinished fort was consequently abandoned with the exception of a small mosque constructed within the ruin of the fortress in the Ottoman period and also occasional squatter settlements.
Table 1 in the Appendix summarizes various intensities and magnitudes of past earthquakes of the area. Two of these earthquakes offset the crusader fortress, first on 20 May 1202, and again on 30 October 1759 (Marco et al. 1997; Ellenblum et al. 1998). Ambraseys and Melville (1988) estimated the magnitude of the 1202 earthquake at MS 7.6 with intensities from VIII to IX over a wide area, ranging from Nablus, south of the SG, to Arqa, in current day Lebanon. For the 30 October 1759 earthquake, Ambraseys and Barazangi (1989) estimated MS 6.6 based on the intensity and the radius of the isoseismal of the area in which the earthquake was felt. From the historical records, Sbeinati et al. (2005) derived intensities up to VIII. The earthquake history of the fortification walls is summarized in Fig. 2.
Palaeoseismological research revealed the surface rupture of the 1202 earthquake along the YF in Lebanon (Daëron et al. 2005), Ateret (Ellenblum et al. 1998), and Bet Saida (Marco et al. 2005), with a probable fault length of ~200 km. The October 1759 rupture was found preserved in the Ottoman mosque at Ateret and in palaeoseismic trenches at Bet Saida (Marco et al. 2005), and the November 1759 rupture was located on the Rachaya Fault (RaF), which has a potential rupture length of about ~50 km (Nemer et al. 2008).
4 Methods
We use a numerical model of the fortress wall to back calculate what type of ground movement caused the current deformation. This approach requires an accurate documentation of the current state of the deformation of the northern fortification walls and a numerical model representing the state of the ruin before it was deformed. Based on estimates of the local tectonic setting and the historical record, different scenarios have been developed to represent diverse potential ground movements. Finally, the results of the simulation are compared with the observed deformation.
4.1 Data acquisition
We documented the site of Tell Ateret with two 3D laser scanning surveys. In an initial survey in 2013, we focused on the deformed northern fortification wall (Fig. 3). We combined 17 individual 3D laser scans to a single-point cloud that provides a detailed image of the current state of the deformation as it has stood since its excavation in 2007 (in the following referenced to as point cloud, PCL). In the second survey, the entire site and its surroundings were extensively surveyed with 3D laser-scans (Hinzen et al. 2017), resulting in a detailed digital terrain model with 5 cm grid resolution (in the following referenced to as DTM). For the development of a numerical model in which the deformation of the fortification wall can be simulated, a thorough reconstruction of the original orientation of the fortification wall is vital. Both the PCL and the DTM provide the foundation for the development of the model of the northern fortification wall. In addition, the PCL was used for comparing the results of the numerical simulations with the in-situ situation.
4.2 Model development
Model construction and all simulations were carried out with 3DEC, a discrete element (DE) software for geotechnical analysis of discontinuous media such as jointed rocks and masonry, developed by Itasca Consulting Group Inc. (itascacg.com, last visit 11.2019). All elements are represented by blocks. The blocks can be subdivided into smaller blocks allowing designation of different material properties. The 3DEC code has been used in several previous archaeoseismological applications and its physical correctness verified (e.g. Psycharis et al. 2003; Alexandris et al. 2004; Oliveira et al. 2012; Lemos et al. 2015).
The geometry of the model is based on the reconstruction of the laser-scan data. The original angle of some corners in the fortification wall could be measured on well-worked ashlars which span the corners and which are still intact (Fig. 4). The ashlars of the inner and outer shell have a width of 0.5 m. The overall width of the fortification wall is 4.4 m. In the enlarged view to the DTM, the current course of the fortification walls is visible (Fig. 4). Two assumptions were made for the reconstruction: (1) the width of the fortification walls is constant within the range of the model and (2) the angles of the inner and outer shell at common corners of the wall are equal. The second assumption is necessary since some parts of the outer shell have not yet been excavated and are still covered by loose material from construction ramps. The latter were still in place as the fortification was under ongoing construction when it was sacked by Saladin on 30. August 1179 (Ellenblum et al. 1998).
Figure 5 illustrates a top view of the final model, which was used as initial state for all numerical simulations. The model is composed of (a) two shells with 0.5 m wide rectangular blocks; (b) a 3.4 m wide filling between the two shells, realized by a convolute of tetrahedral blocks (edge length of 0.5 m) representing the basalt cobbles of the filling; (c) construction ramps confining the fortification walls, also realized by tetrahedral blocks (edge length of 1 m); and (d) a baseplate composed of two separate blocks to enable horizontal movement, incorporating two levels and a slope with a height difference of 1.5 m to represent the natural topography of the site. In total, the final model was composed of 52,864 rigid blocks.
Appropriate material properties must be estimated for all structural elements of the model. As the archaeological remains could not be directly sampled for laboratory tests, published data for similar materials were collected. The limestone of the well-worked ashlars is similar to limestone of the Hazera Formation, material properties of which were published by Kamai and Hatzor (2008). The material parameters of the mortar were taken from Krausz (2002). The density for the basalt is in range of the values estimated by Bourbie et al. (1987). The material properties of the ramps were those of densified soil following Bowles (1996). Table 2 in the Appendix summarizes the material properties of all components.
The properties for the wall joints, normal-stiffness (kn), and shear-stiffness (ks) were estimated following Bui et al. (2017) and Lourenco et al. (2005).
and
where Em and Eb are the Young’s moduli of the mortar and blocks respectively, v is the Poisson ratio of the wall blocks, and hb is the block height, which is 0.67 m for the outer and 0.54 m for the inner shell ashlars. In order to create a stable starting model for the dynamic simulations, the complete model was set to static load conditions for a model time of 5 s to allow the model to settle; the state at the end of the 5 s period was then the starting model for all calculations.
The time history for the ground motion consisted of an analytical cycloidal pulse (Zhang and Makris, 2001) and was used in all simulations. The pulse fulfils the boundary conditions of zero acceleration, velocity, and displacement at the start and zero acceleration and velocity at the end of the signal, while the final displacements match those between the two plates. This signal type was previously successfully applied in archaeoseismological research; the displacement history of the pulse is similar to the horizontal ground movement close to a strike slip event (Hinzen 2009; Hinzen and Montabert 2017).
In the high-resolution PCL of the northern fortification wall, a lateral offset of 1.75 m has been estimated (Fig. 6); this value was used to reconstruct the original position of the wall shells.
4.3 Simulations
We ran a total of 58 simulations for two scenarios. The first scenario focused on the influence of different movement directions and slip velocities of the plates on the resulting deformation pattern. In this scenario, only one movement with a total offset of 1.75 m was considered. The left lateral movement, which is characteristic for the DSF can be the result of different absolute movements of the eastern and western plates. These displacements are not a priori obvious, and therefore, one of the modelling tasks was to decide which movements were the most probable. Figure 7b–e illustrate the potential absolute movements that result in a net left lateral movement. The four movement possibilities were tested in the simulations of the first scenario.
A movement scenario in which both plates are displaced southwards (opposite of Fig. 7e) was not considered because it contradicts the tectonic regime at the DSF. The slip velocities of the first scenario range from 0.1 to 5 m/s. The slow movement is of particular interest in order to estimate the effect of a potential creep movement to the fortification wall. If a significant fraction of the observed wall offset was due to creep, this would reduce the magnitude estimate of the earthquake. The first scenario consisted of a total of 22 simulations.
In the second scenario, the effect of two consecutive movements deforming the northern fortification wall was simulated, to test the current hypothesis that two earthquakes dislocated the fortress walls. According to Ellenblum et al. (2015), the younger (second) event displaced the site by 0.5 m. To achieve a total offset of 1.75 m, the preceding earthquake must have displaced the fortification walls by 1.25 m. Therefore, the simulations of the second scenario were separated into two stages. The first stage offsets the baseplates 1.25 m and in the second stage, the resulting positions of the first stage are further offset by 0.5 m. The first stage included six simulations with different offset velocities. In the second stage, each end status of the first stage simulation was displaced by 0.5 m, with five different offset velocities, resulting in a total of 30 simulations for this stage.
4.4 Comparison of the simulations with measured data
The following procedure was used to objectively compare the results of each test with the in situ observed deformation pattern as shown in the PCL of the northern fortification wall. Due to the lack of common fixed points between the PCL and the numerical model, the best fit between both datasets has been estimated with the Iterative Closest Point (ICP) technique as described by Rusinkiewicz and Levoy (2001). This technique estimates the best fit between the observed and calculated results by reducing the root-mean-square (RMS) of the residual distances in an iterative process. In 3DEC the coordinates of the starting and end position of the vertices of each block were recorded. From the simulation results, a dataset of points representing the outside of the ashlars of the shells was exported and compared with the measured values.
5 Results
5.1 First scenario
The first scenario focused on testing the effect of the direction of plate motions and displacement velocity on the resulting deformation. In nine simulations, the eastern plate moved 1.75 m north (Fig. 7b) with slip velocities of 0.1 m/s, 0.25 m/s, 0.5 m/s, 1 m/s, 2 m/s, 2.5 m/s, 3 m/s, 4 m/s, and 5 m/s.
In the simulation with slip velocities above 2 m/s, blocks which were not covered by the construction ramps dropped out of the wall due to inertial forces. The inertial forces occur during the starting and stopping phases of movement, and with increasing slip velocities, inertial forces contribute progressively to the deformation of the structure. Schweppe et al. (2017) described two failure mechanisms for free-standing walls utilizing cycloidal pulses related to the inertial forces based on the relation between the direction of ground motion due to plate movement and the collapse direction. The so-called first failure mechanism describes the effect when the direction of collapse is in the direction of the ground motion that occurs during the stopping phase. In the second failure mechanism, the direction of collapse is opposite to the direction of ground motion and occurs during the starting phase. The failure effects were present in the calculation results when the displacement velocities were 2 m/s and higher. However, due to the construction of the fortification wall, the blocks of the inner and outer shell did not show the same falling characteristic. For the first failure mechanism, the blocks of one shell were hampered by the filling between the two shells; the blocks of the other shell can drop out. In other words, in a northward movement, blocks fall out of the northern shell, but not from the southern shell. The opposite effect was observed for the second failure mechanism. This result also occurred during simulations with high velocities such that blocks are hampered from falling by the filling and then still drop out during the stopping phase of the movement.
Inertial forces increase proportional to the acceleration of ground motion, the effect of which can be seen in the first nine simulations where higher slip velocities cause stronger inertial forces and thus larger deformation. In the four simulations with velocities of 1 m/s and lower, no effect of the inertial forces on the deformation pattern is observed. To quantify the effect of inertial forces, it is necessary to analyze the displacements of the blocks relative to the movement of the baseplate. A null or small relative displacement indicates that the block only shifted with the baseplate, and inertial forces did not add additional displacement. Conversely, a large vector of relative displacement indicates a considerable influence of inertial forces. This result only applies to the blocks which rest on a moving plate and thus might help differentiate which plate(s) moved during the earthquake(s).
Figure 8 summarizes the vectors of relative displacement between blocks and the baseplate for the low slip velocities. It is evident that the blocks to the right (east) of the fault line show only small vectors of relative displacement. The largest of these occur in the southern shell close to the fault line, where the shell is pulled apart. The largest overall displacement occurs left of the fault line on the locked plate. During the movement of the western plate, the fortification wall is pulled apart and the blocks on the western plate are dragged along with the movement of the eastern plate as long as the friction between interlocking ashlars is large enough. It is important to note that this pulling does not affect the outer shell of the wall section based on the moving plate because its movement is hampered by filling which is backing the shell. Therefore, only the blocks of the inner shell show relative displacement to the baseplate that does not result from inertial forces, but can be attributed to the pulling. The relative displacement vectors of the four simulations shown in Fig. 8 are similar, a strong indicator that no significant inertial forces contributed to the deformation pattern.
In simulations with slip velocities above 2 m/s, both first and second failure mechanisms occurred. Figure 9 shows the absolute displacement vectors (including the displacement of the baseplate). The total deformation in the simulation with 1 m/s slip velocity is the result of the plate movement and a pulling effect (Fig. 8). At a slip velocity of 3 m/s, numerous blocks drop out of the outer shell in the range of the moving plate in the direction of ground motion (first failure mechanism) and out of the inner shell in opposite direction of the ground motion (second failure mechanism). This is the effect of inertial forces during the stop and start phase of movement, respectively. In the simulation with the highest slip velocity, the fortification wall tilts in the direction opposite to the ground motion due to strong inertial forces. In this case, the fortification wall would suffer total destruction if there were no construction ramps buffering the blocks. The strength of the pulling is also influenced by slip velocity. At low slip velocities, the pulling effect reached blocks at larger distance from the fault line than at higher slip velocities (Fig. 9), with the latter causing a “sharper cut” of the wall.
In the other simulations of the first scenario, further movement directions were examined. In six simulations, both plates were moved in opposite directions (Fig. 7c) with velocities of 0.5 m/s, 1 m/s, 2 m/s, 3 m/s, 4 m/s, and 5 m/s, and subsequently, the western plate moved southwards (Fig. 7d) with 1 m/s, 2 m/s, 3 m/s, 4 m/s, and 5 m/s. In further two simulations of this scenario, both plates were moved northward (Fig. 7e) with different displacements and slip velocities.
The quality of the fit between simulation results and the in-situ deformation was quantified with the ICP method in the form of the residual distance between both datasets (Rusinkiewicz and Levoy 2001). The median of the residual distances is a measure of how well the simulations fit the observations; the mean deviation of the median (MD) is a measure for the spread of the residual distances. Where both the median and the MD values are small, the calculations are judged to agree well with the observations (cf. Table 3). Figure 10 shows the MD values in relation to the median of the RMS values for all simulations of the first scenario. It is evident that both the displacement velocity and movement direction strongly influence the deformation in the simulation and thus change the quality of the fit. This result positively clarifies that deformation pattern is measurably influenced by slip velocity. Those cases where the eastern plate was locked and the western plate moved in a southern direction show the largest misfit. The simulations where the western plate is locked and the eastern plate moves north show the best fit, and the simulation with a slip velocity of 3 m/s constitutes the preferred scenario.
5.2 Second scenario
Based on the results of the first scenario, in the second scenario simulations, the western plate was kept locked and velocities above 1 m/s were considered. In this way, the current hypothesis assuming two earthquakes shifted the fortress wall was tested. The total displacement of 1.75 m was separated into two movements. In the first stage, the eastern plate was shifted 1.25 m north with 1 m/s, 2 m/s, 2.5 m/s, 3 m/s, 4 m/s, and 5 m/s slip velocity in six different simulations. With the exception of the somewhat smaller dislocations, the results of these tests were similar to the results of the first scenario with the same slip velocities. In the second stage, each end state of the simulations of the first stage was offset by another 0.5 m with slip velocities of 1 m/s, 2 m/s, 3 m/s, 4 m/s. to 5 m/s. The median and MD of these calculations are listed in Table 4.
Figure 11 compares the results of the second scenario in the same manner as in Fig. 10. The different combinations of the two movements have a discernible effect on deformation. The simulation with the best fit to the observations has a slip velocity of 3 m/s for the displacement of 1.25 m in the first stage and a slip velocity of 1 m/s for the second stage offset of 0.5 m. Comparing the best fit of results from both scenarios shows an overall better fit for the second scenario and strongly supports the two-earthquake hypothesis.
6 Discussion
We examine the deformation of the northern fortification wall of the ruin of the crusader fortress of Tell Ateret with DE models. The historical record and the geological observations support the hypothesis that two earthquakes, the first on 20 May 1202 and the second on 30 October 1759, successively deformed the fortification walls of the fortress (Ellenblum et al. 2015). We show that slow creep movement is unlikely to have caused the observed damage because such motion would not have produced the observed deformations by inertial forces. Based on the results of our simulations and a quantitative comparison to observations from the laser scan reconstruction, the most likely scenario is that two distinct plate movements, where the first offset is 1.25 m at a slip velocity 3 m/s and the second offset 0.5 m at 1 m/s.
Intensities and magnitudes for both the two historical earthquakes have been previously derived from the historical information. The results of our simulations can also be compared to the macroseismic studies. Ambraseys and Melville (1988) estimated an intensity of IX for the earthquake in 1202. Based on the relationship between MM intensity and PGA in California after Wald et al. (1999), an intensity IX would correspond to a PGA between 6.38 and 12.16 m/s2. The cycloidal pulse for the first movement with an offset of 1.25 m and a slip velocity of 3 m/s had a PGA of 11.3 m/s2 and lies within the range given by Wald et al. (1999). The second cycloidal pulse with an offset of 0.5 m and a slip velocity of 1 m/s had a PGA of 3.14 m/s2. This translates to an intensity VII for the 1759 event, which agrees with the results given by Sbeinati et al. (2005).
To estimate the magnitude of the simulated events, a relationship for earthquakes in the Middle East from Ambraseys and Melville (1982) can be used:
where L is the rupture length and D is the relative displacement in cm. Daëron et al. (2005) suggest the potential rupture lengths of 200 km and 50 km for the 1202 and 1759 events, respectively. With 1.25 m offset, the 1202 event corresponds to a magnitude of MS 7.4 and the second event in 1759 with an offset of 0.5 m results in a magnitude of MS 6.7. Both magnitude values lie in the range of published estimate for these earthquakes (Ambraseys and Melville 1988; Ambraseys and Barazangi 1989; Marco et al. 1997).
Previous archaeoseismic studies at the southern end of Tel Ateret (Ellenblum et al. 2015) revealed repeated rupturing of constructions since the post–Iron Age II era and the authors estimated an average slip rate at the site of 2.6 mm/year. This slip rate is significantly less than estimated from GPS surveys with a lower margin of 4.9 ± 1.4 mm/year (Le Beon et al. 2008; Sadeh et al. 2012; Masson et al. 2015; Wechsler et al. 2018) and the longer-term geologic slip rates of ~5 mm/year (e.g. Marco and Klinger 2014) and 7 mm/year reported for farther north in Syria (Meghraoui et al. 2003). Even though these disparate estimates indicate a certain unevenness in the spatial and temporal distribution of slip along the DSF, the archaeologically determined value of 2.6 mm/year can be compared to the results of this study. Assuming that the whole stress on the fault segment at Tel Ateret was released during the 1202 earthquake, the 818 years since the event would accumulate to a 2.1 m deficit in displacement. If we subtract the 0.5 m slip of the 1759 earthquake, a deficit of about 1.6 m remains. According to Ambraseys and Melville (1988), the deficit is equivalent to a gap of a magnitude MS 7.5 earthquake in this part of the Jordan valley (assuming the geodetic slip rate of 5 mm/year the magnitude would be MS 7.8.).
The uncertainties in our approach using a discrete element model are inherent given that the model is only an approximation to the real geometry of the fortification wall and cannot be an exact copy. The material parameters of the model are based on literature values which are, at best, in the range of the used building materials. Further, only a simple ground motion model (cyclic pulse) was used. In all scenarios, the full displacement was assigned to the main earthquake; the assumption that aftershocks also contributed to displacement were not considered. However, we show that inertial forces contribute to the deformation. Therefore, splitting the offset to a main shock and aftershocks would decrease these inertial forces. In addition, the precise slip markers provided by the archaeological walls was considered sufficient justification for using one horizontal movement for each event and neglecting the possible effect of vertical components.
Both terrestrial laser scans that were made at the site (DTM and PCL) provide a possibility for comparison with future surveys. The PCL was made in 2013 and with the estimated minimum slip rate at the site of 2.6 mm/year, a re-scanning after a period of some 10 years should be sufficient to detect creep effects by comparing the two point clouds. And in the event of an earthquake, there is, of course, the opportunity to compare pre- and post-event deformation. A precondition for future comparisons is that the site is sufficiently protected from further deterioration by weather and/or looting.
7 Conclusions
This archaeoseismological study presents the first time that a DEM has been used to deduce dynamic source parameters of an earthquake from the observed deformation of an ancient structure. The DEM results provided a quantifiable differentiation in the deformation pattern of the wall of Tel Ateret based on the variation of key earthquake source parameters: direction of motion, displacement, and slip velocity. Based on the modelling results, post-seismic creep has been excluded as the main reason for the offset. In addition, best fit estimates between model deformations and laser scans of the contemporary ruins support the hypothesis that two rapid movements of the Arabian plate are more likely to have caused the observed deformations than a single movement of the Arabian plate or a major movement of the Sinai Plate. For the best-fitting simulation, the earthquake of May 20th 1202 was associated with an offset of 1.25 m at a slip velocity of 3 m/s. The consequent earthquake, of 30 October 1759, resulted in an offset of 0.5 m at a slip velocity of 1 m/s. In context of the historical record, these values agree well with the previous investigations of these earthquakes. The 1.25 m and 0.5 m slip, with no significant creep contribution, indicates a slip deficit at the Ateret of about 1.6 m and corresponds to an earthquake of magnitude 7.4.
The number of simulations that are possible such as in this study has practical limits (at this time) due to computation times. Particularly, some of the simulations with slow slip velocities took more than a week of computation time on an average performing workstation. Future advances in software code, advanced macro models of brick and mortar systems, and increased hardware capabilities will allow an increased the number of simulations and thus allow more parameter variations, paving the way for probabilistic modelling in quantitative archaeoseismological studies.
References
Alexandris A, Protopapa E, Psycharis I (2004) Collapse mechanisms of masonry buildings derived by the distinct element method. In: Proceedings of the 13th World Conference on Earthquake Engineering 59, No. 548
Alfonsi L, Cinti FR, Di Mauro D, Marco S (2012) Archaeoseismic evidence of two neolithic (7,500-6,000 B.C.) earthquakes at Tell es-Sultan, Ancient Jericho, Dead Sea fault. Seismol Res Lett 83:639–648. https://doi.org/10.1785/0220110144
Altunel E, Meghraoui M, Karabacak V, Akyüz SH, Ferry M, Yalçner Ç, Munschy M (2009) Archaeological sites (Tell and Road) offset by the Dead Sea Fault in the Amik Basin, Southern Turkey. Geophys J Int 179:1313–1329. https://doi.org/10.1111/j.1365-246X.2009.04388.x
Ambraseys NN (2009) Earthquakes in the Mediterranean and Middle East: a multidisciplinary study of seismicity up to 1900. Cambridge University Press, Cambridge
Ambraseys, Jackson, (1998) Faulting associated with historical and recent earthquakes in the Eastern Mediterranean region. Geophysical Journal International 133 (2):390-406
Ambraseys NN, Barazangi M (1989) The 1759 earthquake in the Bekaa valley: Implications for earthquake hazard assessment in the eastern Mediterranean region. J Geophys Res 94:4007–4013
Ambraseys N., Melville C. (1982). A history of Persian Earthquakes, Cambridge
Ambraseys NN, Melville CP (1989) Evidence for intraplate earthquakes in northwest Arabia. Bull. Seism. Soc Am 79:1279–1281
Ambraseys NN, Melville CP (1988) An analysis of the eastern Mediterranean earthquake of 20 May 1202. In: Lee WKH, Meyers H, Shimazaki K (eds) Historical seismograms and earthquakes of the world. Academic Press, San Diego, pp 181–200
Anvi R (1999). Jericho earthquake, comprehensive macroseismic analysis based on contemporary sources. PhD dissertation, Ben Gurion University, Israel, 90 p.
Anvi R, Bowman D, Shapira A, Nur A (2002) Erroneous interpretation of historical doc- uments related to the epicenter of the 1927 Jericho earthquake in the Holy Land. J. Seismol. 6, 469–476.
Austin SA, Franz GW, Frost EG (2010) Amos’s Earthquake: An Extraordinary Middle East Seismic Event of 750 B.C. International Geology Review 42:657–671
Ben-Menahem A (1979) Earthquake catalog for the Middle East (92 B.C.–1980 A.D.). Boll. Geofis. Teor. Appl. 21, 245–310.
Ben-Menahem A (1981) Variation of slip and creep along the levant rift over the past 4500 years. Tectonophysics 80:183–197
Ben-Menahem A (1991) Four thousand years of seismicity along the Dead Sea Rift. Journal of Geophysical Research: Solid Earth 96:20195–20216
Ben-Menahem A, Aboodi E (1981) Micro- and macroseismicity of the Dead Sea rift and off-coast eastern Mediterranean. Tectonophysics 80:199–233
Barber M (1998) Frontier warfare in the Latin Kingdom of Jerusalem: the campaign of Jacob’s Ford, 1178-9. In: France J, Zajac WG (eds) The crusades and their sources. Aldershot, Brookfield, pp 9–22
Bartov Y, Steinitz G, Eyal M, Eyal Y (1980) Sinistral movement along the Gulf of Aqaba—Its age and relation to the opening of the Red Sea. Nature 285:220–221
Begin BZ, Steinberg DM, Ichinose GA, Marco S (2005) A 40,000 Years Unchanging Seismic Regime in the Dead Sea Rift. Geology 33:257–260
Bourbie T, Coussy O, Zinszner B (1987) Acoustic of porous media. Gulf Publishing Co., Houston
Bowles LE (1996) Foundation analysis and design. McGraw-Hill, New York
Bui TT, Limam A, Sarhosis V, Hjiaj M (2017) Discrete element modelling of the in-plane and out-of-plane behaviour of dry-joint masonry wall constructions. Engineering Structures 136:277–294
Condor CR, Kitchner HH (1882) The Survey of Western Palestine. Memoirs of the Topography, Orography, Hydrography, and Archaeology. Palestine Exploration Fund, London, 226-227.
Daëron M, Klinger Y, Tapponnier P, Elias A, Jacques E, Sursock A (2005) Sources of the large A.D. 1202 and 1759 Near East earthquakes. Geology 33:529. https://doi.org/10.1130/G21352.1
Darawcheh R, Margottini C, Paolini S (2000) The 9 July 551 AD Beirut Earthquake, East- ern Mediterranean region. J. Earthq. Eng. 4, 403–414.
Ellenblum R (1998) Frankish Rural Settlement in the Latin Kingdom of Jerusalem. Cambridge University Press, Cambridge
Ellenblum R (2003) Frontier activities: the transformation of a Muslim sacred site into the Frankish Castle of Vadum Iacob. Crusades 2:83–97
Ellenblum R (2007) Crusader castles and modern histories: Cambridge University Press. England, Cambridge
Ellenblum R, Marco S, Agnon A, Rockwell T, Boas A (1998) Crusader castle torn apart by earthquake at dawn, 20 May 1202. Geology 26:303–306. https://doi.org/10.1130/0091-7613
Ellenblum R, Marco S, Kool R, Davidovitch U, Porat R, Agnon A (2015) Archaeological record of earthquake ruptures in Tell Ateret, the Dead Sea Fault. Tectonics 34:2105–2117. https://doi.org/10.1002/2014TC003815
Freund R (1965) A model of the structural development of Israel and adjacent areas since Upper Cretaceous times. Geol Mag 102:189–205
Gomez F, Nemer T, Tabet C, Khawlie M, Meghraoui M, Barazangi M (2007) Strain partitioning of active transpression with the Lebanese restraining bend of the Dead Sea Fault (Lebanon and SW Syria). Geol Soc, London, Special Publications 290:285–303. https://doi.org/10.1144/290.10
Gomez F, Meghraoui M, Darkal AN, Hijazi F, Mouty M, Suleiman Y, Sbeinati R, Darawcheh R, Al-Ghazzi R, Barazangi M (2003) Holocene faulting and earthquake recurrence along the Serghaya branch of the Dead Sea fault system in Syria and Lebanon. Geophysical Journal International 153:658–674
Guidoboni E, Comastri A (2005) Catalogue of earthquakes and tsunamis in the Mediterranean area from the 11th to the 15th Century. Istituto Nazionale di Geofisica, Bologna
Hamiel Y, Amit R, Begin ZBB, Marco S, Katz O, Salamon A, Zilberman E, Porat N (2009) The seismicity along the Dead Sea fault during the last 60,000 years. Bull Seismol Soc Am 99:2020–2026. https://doi.org/10.1785/0120080218
Hinzen K-G (2009) Simulation of toppling columns in archaeoseismology. Bull Seismol Soc Am 99:2855–2875. https://doi.org/10.1785/0120080241
Hinzen K-G, Montabert A (2017) Rectangular blocks vs polygonal walls in archaeoseismology. Ann Geophys 60. https://doi.org/10.4401/ag-7127
Hinzen K-G, Arav R, Filin S, Marco S, Schweppe G (2017) High resolution DTM reveals tectonic signal of the Dead Sea Fault at the Ateret archaeological site. Seismol Res Lett 88:531–723. https://doi.org/10.1785/0220170035
Hough SE, Avni R (2009) The 1170 and 1202 CE Dead Sea Rift earthquakes and long-term magnitude distribution of the Dead Sea Fault Zone. Israel Journal of Earth Sciences 58:295–308
Kamai R, Hatzor YH (2008) Numerical analysis of block displacements in ancient masonry structures: a new method to estimate historic ground motions. Int J Numer Anal Methods Geomech 32:1321–1340
Karcz I, Kafri U (1978) Evaluation of suposed archaeoseismic damage in Israel. J Archaeol Sci 5:237–253
Karcz I (2004) Implications of some early Jewish sources for estimates of earthquake hazard in the Holy Land. Annals of Geophysics, v. 47, p. 759–792.
Krausz K (2002) Tragverhalten gemauerter Tonnengewölbe mit Stichkappen. Universität Stuttgart, Dissertation
Le Beon M, Klinger Y, Amrat AQ, Agnon A, Dorbath L, Baer G, Ruegg J-CC, Charade O, Mayyas O (2008) Slip rate and locking depth from GPS profiles across the southern Dead Sea Transform. J Geophys Res 113:1–19. https://doi.org/10.1029/2007JB005280
Lemos JV, Oliveira CS, Navarro M (2015) 3-D Nonlinear behavior of an obelisk subjected to the Lorca May 11, 2011 Strong Motion Record. Eng Fail Anal 58:212–228
Lourenco PB, Oliveira DV, Roca P, Orduna A (2005) Dry joint stone masonry wall subjected to in-plane combined loading. J Struct Eng 131:1665–1673
Marco S, Klinger Y (2014) Review of on-fault palaeoseismic studies along the dead sea fault. In: Garfunkel Z, Ben-Avraham Z, Kagan E (eds) Dead Sea Transform Fault System: Reviews, Springer, 6:183–205. doi:https://doi.org/10.1007/978-94-017-8872-4_7
Marco S, Hartal M, Hazan N, Lev L, Stein M (2003) The surface rupture of the January 18, 749 earthquake excavated in Tiberias, in Feinstein, S., Agnon, A., Farber, E., Ezra, S., Avni, Y., and Levi, Y. eds., Isr. Geol. Soc. Ann. Meeting, En Boqeq, p. 80.
Marco S, Agnon A, Ellenblum R, Eidelman A, Basson U, Boas A (1997) 817-year-old walls offset sinistrally 2.1 m by the Dead Sea Transform, Israel. J Geodyn 24:11–20
Marco S, Rockwell TK, Heimann A, Frieslander U, Agnon A (2005) Late Holocene activity of the Dead Sea Transform revealed in 3D palaeoseismic trenches on the Jordan Gorge segment. Earth Planet Sci Lett 234:189–205. https://doi.org/10.1016/j.epsl.2005.01.017
Masson F, Hamiel Y, Agnon A, Klinger Y, Deprez A (2015) Variable behavior of the Dead Sea Fault along the southern Arava segment from GPS measurements. Compt Rendus Geosci 347:161–169. https://doi.org/10.1016/j.crte.2014.11.001
Meghraoui M, Gomez F, Sbeinati R, van der Woerd J, Mouty M, Darkal AN, Radwan Y, Layyous I, al Najjar H, Darawcheh R, Hijazi F, al-Ghazzi R, Barazangi M (2003) Evidence for 830 years of seismic quiescence from palaeoseismology, archaeoseismology and historical seismicity along the Dead Sea fault in Syria. Earth Planet Sci Lett 210:35–52
Migowski C, Agnon A, Bookman R, Negendank JFW, Stein M (2004) Recurrence pattern of Holocene earthquakes along the Dead Sea transform revealed by varve-counting and radiocarbon dating of lacustrine sediments. Earth and Planetary Science Letters 222:301–314
Nemer T, Meghraoui M (2006) Evidence of coseismic ruptures along the Roum fault (Lebanon): a possible source for the AD 1837 earthquake. Journal of Structural Geology 28:1483–1495
Nemer T, Meghraui M (2020) A non-active fault within an active restraining bend: the case of the Hasbaya fault, Lebanon. J Struct Geol 136:104060. https://doi.org/10.1016/j.jsg.2020.104060
Nemer T, Meghraoui M, Khair K (2008) The Rachaya-Serghaya fault system (Lebanon). Evidence of coseismic ruptures, and the AD 1759 earthquake sequence. J Geophys Res 113:B05312
Niemi TM, Zhang HW, Atallah M, Harrison JBJ (2001) Late Pleistocene and Holocene slip rate of the Northern Wadi Araba fault, Dead Sea Transform, Jordan. J Seismol 5:449–474. https://doi.org/10.1023/A:1011487912054
Oliveira DV, Greechi G, McCall A, Noh J, Speer E, Tohidi M (2012) Seismic analysis of the Roman temple of Evora, Portugal. In: 15th World Conference on Earthquake Engineering. Sociedade Portuguesa de Engenharia Sísmica 1-10
Psycharis IN, Lemos JV, Papastamatiou DY, Zambas C, Papantonopoulos C (2003) Numerical study of the seismic behavior of a part of the Parthenon Pronaos. Earthq Eng Struct Dyn 32:2063–2084
Quennell AM (1956) Tectonics of the Dead Sea rift. In: Congreso Geologico Internacional, 20th sesion edn. Asociacion de Servicios Geologicos Africanos, Mexico City, pp 385–405
Rusinkiewicz S, Levoy M (2001 Efficient variants of the ICP algorithm. In: Proceedings Third International Conference on 3-D Digital Imaging and Modeling 145–152. doi:https://doi.org/10.1109/IM.2001.924423
Sadeh M, Hamiel Y, Ziv A, Bock Y, Fang P, Wdowinski S (2012) Crustal deformation along the Dead Sea Transform and the Carmel Fault inferred from 12 years of GPS measurements. J Geophys Res Solid Earth 117:8. https://doi.org/10.1029/2012JB009241
Sbeinati MR, Darawcheh R, Mouty M, Compositori E (2005) The historical earthquakes of Syria: an analysis of large and moderate earthquakes from 1365 B.C. to 1900 A.D. Ann Geophys 48:347–435
Schweppe G (2019) The discrete element method in archaeoseismological research—two case studies in Israel. University of Cologne, Doctoral dissertation
Schweppe G, Hinzen K-G, Reamer SK, Fischer M, Marco S (2017) The ruin of the Roman Temple of Kedesh, Israel: example of a precariously balanced archaeological structure used as a seismoscope. Ann Geophys 60:7152. https://doi.org/10.4401/ag-7152
Stiros SC, Jones RE (eds.) (1996) Archaeoseismology. BritishSchool at Athens, Fitch Laboratory Occasional Paper 7
Turcotte T, Arieh E (1988) Catalog of Earthquakes in and around Israel. Israel Electric Corporation, Haifa.
Wald DJ, Quitoriano V, Heaton TH, Kanamori H (1999) Relationships between peak ground acceleration, peak ground velocity, and modified Mercalli intensity in California. Earthquake Spectra 15:557–564. https://doi.org/10.1193/1.1586058
Wechsler N, Rockwell TK, Klinger Y (2018) Variable slip-rate and slip-per-event on a plate boundary fault: The Dead Sea fault in northern Israel. Tectonophysics 722:210–226
Wells DL, Coppersmith KJ (1994) New empirical relationships among magnitudes, rupture length, rupture width, rupture area, and surface displacement. Bull Seismol Soc Am 84:974–1002
Zohar M, Salamon A, Rubin R (2017) Earthquake damage history in Israel and its close surrounding—evaluation of spatial and temporal patterns. Tectonophysics 696:1–13. https://doi.org/10.1016/j.tecto.2016.12.015
Zhang J, Makris N (2001) Rocking Response of Free-Standing Blocks under Cycloidal Pulses. Journal of Engineering Mechanics 127:473–483
Acknowledgements
We thank Elisa J. Kagan and Erez Hasul who helped us during the scanning of the northern section of the ruins. Fieldwork and processing of the DEM of Ateret were in part done by Reuma Arav and Sagy Filin. The main software tool 3DEC was made available for this study, thanks to the ITASCA Educational Program (IEP) by the ITASCA Consulting Group Inc. We especially thank Lothar te Kamp for the mentorship in the course of the IEP. We are indebted and thankful to our friend and colleague Ronnie Ellenblum, who led the excavations at Tell Ateret and passed away in January 2021.
Funding
Open Access funding enabled and organized by Projekt DEAL. The study was in part funded by a grant #1165 of the German Israel Foundation (GIF) to KGH and SM.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Appendix
Appendix
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Schweppe, G., Hinzen, KG., Reamer, S.K. et al. Reconstructing the slip velocities of the 1202 and 1759 CE earthquakes based on faulted archaeological structures at Tell Ateret, Dead Sea Fault. J Seismol 25, 1021–1042 (2021). https://doi.org/10.1007/s10950-021-10009-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10950-021-10009-0