Abstract
In 2011, an amplification map achieved by macroseismic information was developed for Switzerland using the collection of macroseismic intensity observations of past earthquakes. For each village, a ΔIm was first derived, which reflects the difference between observed and expected macroseismic intensities from a region-specific intensity prediction equation. The ΔIm values are then grouped into geological/tectonic classes, which are then presented in the macroseismic amplification map. Both, the intensity prediction equation and the macroseismic amplification map are referenced to the same reference soil condition which so far was only roughly estimated. This reference soil condition is assessed in this contribution using geophysical and seismological data collected by the Swiss Seismological Service. Geophysical data consist of shear-wave velocity profiles measured at the seismic stations and earthquake recordings, used to retrieve empirical amplification functions at the sensor locations. Amplification functions are referenced to a generic rock profile (Swiss reference rock condition) that is well defined, and it is used for the national seismic hazard maps. Macroseismic amplification factors Af, derived from empirical amplification functions, are assigned to each seismic station using ground motion to intensity conversions. We then assess the factors dΔf defined as the difference between Af and ΔIm. The factor dΔf accounts for the difference between the reference soil condition for the intensity prediction equation and the Swiss reference rock. We finally analysed relationships between Af and proxies for shear-wave velocity profiles in terms of average shear-wave velocity over defined depth ranges, such as VS,30, providing an estimate of the reference shear velocity for the intensity prediction equation and macroseismic amplification map. This study allows linking macroseismic intensity observations with experimental geophysical data, highlighting a good correspondence within the uncertainty range of macroseismic observations. However, statistical significance tests point out that the seismic stations are not evenly distributed among the various geological–tectonic classes of the macroseismic amplification map and its revision could be planned merging classes with similar behaviour or by defining a new classification scheme.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
Site-specific seismic hazard assessment requires an estimate of site effects, quantifying frequency-dependent amplification due to geological settings (e.g. Roten et al. 2008; Panzera et al. 2016; Michel et al. 2017). In urban areas struck by earthquakes, an alternative method to identify amplification zones consists in the use of macroseismic observations (e.g. Carlino et al. 2010; Sbarra et al. 2012; Panzera et al. 2018). In few cases, this approach was also applied at the national level (e.g. Sousa and Oliveira 1996; Fäh et al. 2011). Although such national macroseismic amplification maps allow detecting the average behaviour at the regional scale, they are not applicable locally (Pettenati et al., 2018).
A macroseismic amplification map for Switzerland (Fig. 1) was developed from the collection of macroseismic intensity observations of past earthquakes and taking into account a set of geological–tectonic classes (Kaestli and Fäh 2006; Fäh et al. 2011). The map is presented in terms of ΔIm, which is the average of the difference between observed and expected macroseismic intensities from a region-specific intensity prediction equation for each geological–tectonic class (Fäh et al. 2011). Both, the intensity prediction equation and the macroseismic amplification map are referenced to the same reference soil condition which was so far only estimated by expert opinion. The macroseismic amplification map for Switzerland is implemented in the Swiss Seismological Service (SED) shake map tool (Cauzzi et al. 2015) to account for site effects at the national scale.
Geophysical and seismological data collected by SED in the framework of different national projects are used here to check and validate the macroseismic amplification map. The geophysical data consist of shear-wave velocity profiles measured at seismic stations (Fäh et al. 2009; Michel et al. 2014; Poggi et al. 2017; Hobiger et al. 2017) using passive and/or active seismic methods. As for seismological data, earthquake recordings are used to retrieve empirical amplification functions at the sensor locations using the spectral modelling method (Edwards et al. 2013). Amplification functions are referenced to a generic rock profile (Swiss reference rock condition) that is well defined (Poggi et al. 2011). The national seismic hazard maps (Wiemer et al. 2016) refer to this generic rock profile. The elastic and the anelastic Fourier amplification functions are converted to pseudo-spectral acceleration (PSA) amplification functions resorting to random vibration theory (SMSIM code - Boore, 2003).
Using these datasets, we investigate the reference soil conditions of the regional intensity prediction equation and the related macroseismic amplification map. Such information is needed to compare probabilistic seismic hazard assessment in ground motion on a well-defined reference rock profile with that for macroseismic intensity.
2 Macroseismic amplification map
Macroseismic observations (intensity data points (IDP)) are routinely collected by SED after felt events. The macroseismic data are validated and stored in a dedicated database. This database also comprises reports and macroseismic data points from historical events. The macroseismic intensity dataset includes around 35,000 intensity assignments collected from 17,000 settlements in Switzerland and for 720 earthquakes since 1850 (Kaestli and Fäh 2006), as well as macroseismic data for the time before 1850 for all events that reached EMS-98 intensity VI. This macroseismic dataset was used for the compilation of the EMS-98 intensity amplification map of Switzerland (Fig. 1). The macroseismic amplification factors are defined relative to a macroseismic intensity prediction equation and calibrated on a set of geological soil classes as documented in Fäh et al. (2011). The mapped values refer to a soil reference condition that is different to the Swiss reference rock (VS,30 = 1105 m/s) proposed by Poggi et al. (2011) and used in the calculation of the Swiss seismic hazard (Wiemer et al. 2016). This should be accounted for by a constant correction term which, as proposed by Fäh et al. (2011), is about 1/2 intensity units (namely 0.47). Such correction allows the necessary adjustment to the Swiss reference rock condition.
The IDP were grouped into soil classes defined by a combination of geological and tectonic characteristics, drawn from the geological map of Switzerland 1:500,000 (Swisstopo 2005). Median ΔIm were computed for the defined geological soil and rock classes. The resulting ΔIm range between − 0.31 (in the Swiss Alps) and + 1.05 intensity units (in the Basel region and in the alluvium-filled alpine basins). The map is delivered in vector format whose polygons enclose areas with equal macroseismic amplification factor. For polygons without an assignment, the amplification was defined as ‘unknown’. This macroseismic amplification map was implemented in the ShakeMap tool (USGS code as described in Wald et al. 2005) at SED and tested in combination with the Swiss stochastic ground motion prediction equation, in the sense that we can reproduce at the national scale the ground shaking scenario of the strong historical earthquakes in Switzerland (Cauzzi et al. 2015). Reference soil conditions and uncertainties related to these amplifications were never assessed thoroughly so far, but this is a key issue when comparing seismic hazard estimated in macroseismic intensity with the one in ground motion. Macroseismic information can also be used in support to regional studies for the identification of areas of anomalous seismic response (e.g. Fäh et al. 2011). Due to the large uncertainty, however, this information should always be complemented with other kind of observations at the local scale.
3 Seismic site response observed at seismic stations
3.1 Soil class categorisation and empirical amplification functions
The national seismic networks of Switzerland (Fig. 2) comprise almost 200 permanent stations equipped with accelerometers and/or with velocimeters (strong motion—SSMNet and broadband—SDSNet). In this study, stations in tunnels and boreholes were discarded, thus leaving 132 free-field and urban free-field sites. Their distribution in the Swiss territory is illustrated in Fig. 2, whereas Tables 1 and 2 summarise the distribution according to the soil classification in the Swiss building codes SIA-261 (2014) and in the geology/tectonic units of the macroseismic amplification map, respectively. The soil classification is assigned based on S-wave measurements available for 91 station sites. As for the geological/tectonic units of the macroseismic amplification map, only 109 of the 132 considered seismic station sites have an assignment. The other 23 stations are mostly located on rock formations for which no IDP are available.
For each of the considered seismic stations, empirical amplification functions are routinely computed by using the SED system after each earthquake, using empirical spectral modelling (Edwards et al. 2013). The method is equivalent to the well-known approach in which source, path, and site effects are separated through a generalised inversion (Field and Jacob, 1995). In particular, for each recorded event, the source spectrum is computed with associated stress drop and moment magnitude, taking into account regional geometrical decay and path attenuation (Edwards and Fäh 2013). Finally, the elastic site amplification function is extracted for each processed earthquake, resulting in event-specific amplification added to the statistical representation of the database site response functions. With time, after many processed earthquakes, the robustness of the station amplification results is improving (Edwards et al. 2013). Finally, resorting to random vibration theory (SMSIM code - Boore 2003), a PSA amplification function is obtained. The reference soil condition of the amplification functions is the Swiss reference rock model (Table 1).
3.2 PSA amplification to macroseismic amplification factors
A macroseismic amplification factor ΔIm was assigned to each seismic station according to the station position in the macroseismic amplification map. At the same time, a set of macroseismic amplification factors Af was derived from the measured PSA amplification factors (Amp(T)), using the ground motion to intensity conversion equations (GMICE), proposed by Faenza and Michelini (2010 and 2011), FM10&11:
where IMCS is the macroseismic intensity in Mercalli–Cancani–Sieberg, PGV is the peak ground velocity, PGA is the peak ground acceleration, and SA is the spectral acceleration at 0.3, 1.0, and 2.0 s period T. The FM10&11 relationships are suitable for Switzerland and are implemented in SED-ShakeMap (Cauzzi et al. 2015). Moreover, the FM10&11 relationships have the advantage that they were developed using orthogonal regression, making possible their use in two directions, from ground motion parameters to intensity and from intensity to ground motion parameters. Each equation allows deriving an intensity increment Af:
where b is the slope coefficient of the relationships [1] to [5]. Although the amplification map of Switzerland is based on EMS-98, it shares almost similar intensity values with the MCS up to about intensity VIII (e.g. Musson et al. 2010; Cauzzi et al. 2015; Panzera et al. 2018). Therefore, sets of Af values were derived from PSA amplification functions at the periods of 0.3 s, 1.0 s, and 2.0 s, as well as for PGV and PGA.
4 Comparison between ΔIm and Af factors
In Fig. 3, the Af values are plotted against ΔIm, highlighting very low coefficients of correlation R-squared (R2) due to the structure of macroseismic intensity that is conserved in the ΔIm (Pettenati and Sirovich 2007). The coefficient of correlation is estimated as the ratio between the sum of squares due to regression (RSS) and total sum of squares (TSS). Moreover, the high ΔIm variability is expected, if we consider that the macroseismic map does not capture small-scale variations in seismic site response, because it is built considering average ΔIm in an area.
The linear fits in Fig. 3 were computed for two different datasets which differ only for the ΔIm assigned to the alluvial plains (grey points with blue dots and grey points with red dots). Fäh et al. (2011) obtained for this geologic/tectonic unit a median macroseismic amplification factor 0.33, but they suggested to use conservatively the 75th percentile value 1.05 in the shake map application (Cauzzi et al. 2015). In this way, the authors wanted to account for the urban development in the twentieth century into areas of unfavourable soil behaviour in alluvial plains. These areas are not sufficiently covered by historical IDP used to derive the amplification map.
Since the soil S-wave velocity reference for ΔIm is lower than the rock reference for Af, the curves in Fig. 3 are above the 1:1 green lines. Moreover, for PGA, PGV, and SA at 0.3 s, the curves are almost parallel to the 1:1 green lines, which is desirable. For the SA periods 1.0 and 2.0 s, the curves are not parallel to the 1:1 curve, with a decreasing trend towards higher ΔIm. With increasing ΔIm, observed amplification Af, derived from ground motion at longer periods, becomes smaller with respect to T = 0.3 s. For longer periods, the influence of the deeper structure is more relevant. Therefore, it seems that the deeper structure is not reflected in the amplification derived from IDP. When the conservative 75th percentile of the observed ΔIm for alluvial plains is used, for the periods 1.0 and 2.0 s, the linear fit line falls below the 1:1 green line, which is unphysical (Fig. 3). In this case, at ΔIm = 0.0, the Af, obtained as dΔf = Af − ΔIm, is in the range 0.18–0.46 (Fig. 3), and it is higher if only PGA, PGV, and T = 0.3 s are considered (0.28 ≤ dΔf ≤ 0.46). The linear fits performed using median values of the observed ΔIm show slope coefficients higher than 0.82 for PGA, PGV, and T = 0.3 s, and it is possible to observe that the linear fit lines lie always above the 1:1 green lines. At ΔIm = 0.0, the Af, obtained as dΔf = Af − ΔIm, is in the range 0.27–0.56 (Fig. 3). For PGA, PGV, and T = 0.3 s, the range is narrower (0.32 ≤ dΔf ≤ 0.56). The latter is the closest dΔf = Af − ΔIm to the suggested constant correction term of 0.47 (1/2 intensity units) of Fäh et al. (2011), which was suggested to account for the necessary adjustment to Swiss reference rock conditions.
The dΔf computed for each considered seismic station site can also be analysed to assess if their distribution is normal and to determine its mean value (Fig. 4). Using the Kolmogorov–Smirnov test (Murphy et al. 1968), we found, with a 95% confidence level, that the data are significantly drawn from a normal distribution (p value ≥ 0.05), although distributions are moderately skewed (skewness ≤ 0.5). The analysis was performed using the median ΔIm for alluvial plains. The dΔf are distributed following a normal distribution, with the mean dΔf values between 0.17 and 0.52. These values are in agreement with the one observed in Fig. 3.
From the performed analysis, we obtain that the macroseismic amplification map and consequently ΔIm values are better represented when Af is computed at T = 0.3 s, PGV, and PGA. Most of the observed ΔIm were derived from intensities in the lower intensity grades below VI. At these intensities, no damage occurs, and intensity is best correlated with PGV and PGA (e.g. Omine et al. 2008). Therefore, observed Af derived from PGV and PGA might best compare to ΔIm. The correction factor (mean dΔf) due to the different soil/rock references is therefore best measured from PGV (0.37 ≤ dΔf ≤ 0.42) and PGA (0.52 ≤ dΔf ≤ 0.56). This range of values is the closest to the constant correction of 0.47 (1/2 intensity units) suggested by Fäh et al. (2011). When we consider intensity grades, where damage to buildings is described (VI and above), we should not use PGA anymore, but PGV and SA at the period of the buildings (e.g. Wu, 2003). For the Swiss building stock, Michel et al. (2017) suggested SA at 0.3 s when considering the vibration periods of typical buildings. Therefore, for the higher intensity grades, the best selection to correct for the difference in reference soil/rock condition is from T = 0.3 s (0.31 ≤ dΔf ≤ 0.32, see Figs. 3 and 4), together with PGV (0.37 ≤ dΔf ≤ 0.42, see Figs. 3 and 4).
5 Reference soil condition from the available V S,30 of the geologic/tectonic units
In section 3, we have shown that there exists a discrepancy of dΔf between Af and ΔIm, which can be explained in terms of different reference soil/rock conditions. In particular, the Swiss reference rock used in the computation of the empirical amplification functions is stiffer than the one expected for the macroseismic amplification map. This aspect can be highlighted using the IDP and corresponding VS,30 values for each geologic unit (Table 2).
Figure 5 shows that only 8 classes, with a low number of intensity observations (< 100), have no VS,30 measurements. About 40% of the IDP belong to ‘fluvioglacial/glaciolacustrine gravels’ and ‘moraines on midland molasses’ formations. The weighted average of VS,30 \( \Big({\overline{\ V}}_{S,30} \)) and the corresponding standard deviation (σVS, 30) were computed using the following relationships:
where M is the number of weight that are not equal to zero in each soil class.
From this analysis, it is possible to affirm that most of the IDP have a VS,30 in the range 258–687 m/s with an average value of 472 ± 214 m/s. Moreover, it is also possible to highlight that the highest and lowest VS,30 values are related to few IDP on the ‘malm cover’ and ‘organic soil formations’.
In order to highlight the soil classes for which the macroseismic amplification map might underestimate or overestimate the amplification level, the dΔf were plotted versus the SIA-261 (2014) soil classification (Fig. 6 and Table in supplementary material S1 in which the obtained dΔf values for each SIA-261 (2014) soil class are summarised). From Fig. 6, it is possible to infer that, as expected, dΔf is negative for soil class A and it is positive for the remaining soil classes. For soil type A, there are many instrumented sites on hard rock conditions with high S-wave velocities (soil class A is defined as VS,30 ≥ 800 m/s), while IDP in localities on hard rock are expected to be rare, because urbanised areas generally are not on hard rock but on sediments or weathered sedimentary rock. Therefore, the macroseismic amplification map does not cover well sites on hard rock. This trend is well observed in all the considered spectral ordinates, but particularly for T = 0.3 s, PGV, and PGA (Fig. 6). Moreover, it is possible to presume that the first soil class (starting with hard material soil class A), in which a positive ΔIm is expected for the macroseismic amplification map, is in the velocity range of soil class B (500 ≤ VS,30 < 800 m/s). In particular, this analysis reveals that the average dΔf for soil classes B and C are the closest to the values in Fig. 3, confirming that these two classes are the most represented in the dataset used to draw the macroseismic amplification map. The dΔf for these classes can be explained mainly as difference between the reference soil condition for the intensity prediction equation and the Swiss reference rock. For soil class A, dΔf is lower than 0.20 (average value of all the considered SA for soil class B), meaning that the macroseismic amplification map is slightly overestimating amplification. On the other hand, for soil class D, dΔf is always much higher with respect to the other soil classes and mainly above dΔf > 0.40 (average value of all the considered SA for soil class C). The overestimation on soil class A and underestimation on soil class D are due to the fact that the macroseismic amplification map was derived considering observations mainly from soil classes B and C (more favourable to human settlement). This means that the macroseismic amplification map underestimates the amplification on sites with soil class D, as already suggested by Fäh et al. (2011).
The analysis was also performed plotting the VS,30 versus dΔf (Fig. 7), obtaining similar results as in Fig. 6. In particular, for SA (0.3 s), PGV, and PGA, dΔf with VS,30 between about 400 and 600 m/s are the closest to the values in Fig. 3; dΔf for VS,30 lower than 300 m/s are always the highest; and the dΔf with VS,30 higher than 625 m/s tend to be negative. This means that the macroseismic amplification map has the tendency to provide too high values for non-weathered rock materials and too low values for the soft sediments in soil class D. Moreover, from Fig. 7, we can provide an estimate of the reference soil condition of the macroseismic amplification map, in terms of a VS,30 range of 400–600 m/s.
6 Relationships between Af and V S proxy
The relationships between macroseismic intensity increment Af and simplified site response proxies; the quarter-wavelength velocity (VQWL) at 0.3 s, 0.5 s, and 1.0 s; and the average velocity (VS,Z), with Z equal to 10, 20, 30, 50, and 100 m, were derived at each seismic station from measured velocity profiles. In Figs. 8 and 9, we show the scatterplot VS,Z versus Af for spectral period 0.3 s and PGV, but in supplementary material S0, the scatterplots for spectral periods 1.0 s and 2.0 s as well as for PGA are also available. The VS,Z, when plotted versus Af, highlight a non-linear distribution of points. Therefore, several non-linear curves were tested for the fit, assuming as best a logarithmic function having the following form:
where VX is either VS,Z or VQWL. Such functional form is suggested in empirical ground motion prediction equations (e.g. Cauzzi et al. 2015) to account for the site amplification. From our analysis, we excluded too low and too high Af estimating the mean and standard deviation values for each considered SA period. This selection was made in order to remove seismic stations located in peculiar geologic settings. The VX values were then subdivided in bins of 100 m/s, with associated mean and standard deviation. In a similar fashion, Af falling in each velocity bin were averaged and the standard deviation was computed (blue squares and bars in Figs. 8 and 9 and in Fig. S0). The best fit was found assuming both VX and Af as affected by errors, using then \( {\sigma}_{V_X} \) and σAf standard deviations as weights. In this way, points with high standard deviations were weighted less in the fitting. Moreover, the non-linear fit was made forcing the curve through the coordinates VX equal to Swiss rock reference condition and Af = 0, for all the considered SA (green diamond in Figs. 8 and 9 and in Fig. S0).
The obtained regression equations, with the corresponding coefficient of determination (R2), are plotted in Figs. 8 and 9 (S0 for PGA and the other spectral periods). For all the considered SA periods, the R2 is high enough to affirm that a good correlation exists between the considered parameters. Anyway, in general, the best correlation with the considered proxies is obtained with Af estimated at 0.3 s and from PGV (Table 3). For the spectral periods 1.0 s and 2.0 s, the decrease in R2 could be explained considering that velocity proxies alone are not sufficient to explain low frequency site effects (e.g. valleys). For PGA, the correlation decreases with increasing thickness of the considered structure.
The dΔf obtained in the analysis of Fig. 3 can be used to infer an indication on the macroseismic amplification map VX soil reference condition. Therefore, the dΔf of the considered SA, PGV, and PGA were used to find the corresponding VX (yellow diamonds in Figs. 8 and 9 and in Fig. S0) of the reference soil condition in the ‘macroseismic amplification’ map. Table 4 summarises the VX value at which ΔIm = 0 is expected. The estimated values are only indicative, as especially dΔf are affected by high variability (see Fig. 3). The mean values for the different VX in Table 4 can be considered a representation of the reference velocity profile of the ‘macroseismic amplification’ map.
7 Statistical significance of geological/tectonic classification with respect to the Af
We also tested the significance of the geological/tectonic classification of the macroseismic amplification map when this is related to the measured site response at seismic stations. We verified if the local amplifications observed at stations from the same geological/tectonic unit are homogeneous and if each unit actually differs from the amplification behaviour observed at the other formations.
For this purpose, we first classified the amplification factors for PSA (Amp) at period T of 0.3, 1.0, and 2.0 s; PGV; and PGA measured at every Swiss station, according to the geological/tectonic affiliation of the latter. The number of stations belonging to each unit is generally quite low (Table 2; in average 3.22 stations per class), with 11 classes lacking any stations. We assumed to be able to make some inference on the statistical significance of the amplification behaviour of the units hosting at least 4 stations. Only 7 units fulfil this criterion: ‘moraines on midland molasses’, ‘alluvial plains, debris cones’, ‘fluvioglacial/glaciolacustrine gravels’, ‘Gneiss micaschist’, ‘Muschelkalk Jura chain (Mesozoic)’, and ‘upper freshwater molasses’.
Figure 10, first five panels, displays the distribution of the considered Amp by geologic/tectonic class; factors from individual sites appear to approximately follow a consistent behaviour within each class, with moderate scatter (in 77% of the cases, the standard deviation of log(Amp) for an individual class is smaller than the σ of the overall population). Some classes (e.g. ‘upper freshwater molasses’) bear greater homogeneity (smaller σ) than others (e.g. ‘moraines on midland molasses’), generally in a consistent way for all periods.
The standard deviations for each class of the PSA amplification factors were also translated into σ of macroseismic intensity increment (σ(Af) in Fig. 10 lower right subplot), applying Eqs. 1–5; hence, they can be collated with the corresponding σ from the IDP database (Fäh et al. 2011). The numerical values are reported in Table 5. Standard deviations derived from empirical amplifications at Swiss stations are generally lower (by ~ 25%) than the σ(Af) directly obtained from the IDP. Interestingly, geological classes with wider variability in macroseismic data (black dashed line in Fig. 10) preserve higher values of standard deviations also when the latter are indirectly extracted from recorded earthquake data (coloured lines). This suggests that some classes are intrinsically characterised by a higher (or a lower) variance of the site response, independently of the method used to estimate it.
To determine the amplification ordinate (PGA, T = 0.3–2.0 s, PGV) for which the geological/tectonic subdivision of the ‘macroseismic amplification’ map is more successful in defining homogeneous classes, we compute for each ordinate a pseudo-coefficient of determination:
where TSS is the total sum of the squares over the entire population of n amplification factors in log scale ai (log(Amp)), and SSD is the sum of the squared differences between each aj and the average \( \overline{a_c} \) from its class. A high pseudoR2 (its maximum value being 1) means that the considered classification groups the amplification factors into internally consistent subgroups; vice versa, values close to 0 denote an ineffective categorisation. According to the pseudoR2 we obtained, the ‘macroseismic amplification’ map classification is the most effective for PGV (pseudoR2 = 0.42), followed by the 0.3 s spectral period (0.39), PGA and 1 s spectral period (0.35), and finally 2 s spectral period (0.28). This behaviour was already highlighted by several authors (e.g. Wu 2003; Kaka and Atkinson 2004) who found that earthquake damage statistics show a closer correlation with the PGV distribution; in fact, PGV is a more reliable indicator of seismically induced strains in the shallow subsurface, thus more in accordance with damage distribution.
Finally, to determine whether the empirically observed amplification for a given class differs significantly from the behaviour of the other units, we collated the average log(Amp) values from every couple of considered classes through the unequal variances t test (Welch 1947; see Bergamo et al. 2019 for similar applications). When the test’s null hypothesis—which the two populations’ means are statistically equivalent (with a 90% confidence level)—is verified, the two geological/tectonic units then have similar amplification behaviours; if the hypothesis is rejected, we infer that the two classes may have significantly different average responses. The matrices in Fig. 11 represent the outcomes of the statistical test for each spectral period and for every classes pair. In all panels, many couples of classes present statistically equivalent mean amplifications (red squares); we actually have only one case (Gneiss Micaschist, period 0.3 s) where a subgroup succeeds in having an average amplification value not equivalent to any of the other classes. PGV has the highest number of class pairs with not equivalent means (12 out of 21 possible unordered couples), while PGA has the lowest (7 out of 21); as for PSA amplification factors, the not equivalent pairs amount to 11.
8 Discussion and concluding remarks
In this work, we collate macroseismic intensity observations in terms of ΔIm (local response expressed in macroseismic amplification) with experimental geophysical data, highlighting a good correspondence. The ΔIm in the current Swiss macroseismic amplification map refer to another S-wave velocity reference than the one (VS,30 = 1105 m/s; Poggi et al. 2011) used in the calculation of the empirical amplification functions (Edwards et al. 2013) and for the Swiss seismic hazard (VS,30 of 1105 m/s; Wiemer et al. 2016). Fäh et al. (2011) suggested a constant correction term of about + 1/2 intensity units (namely 0.47), accounting for the necessary adjustment of the macroseismic amplification map to the Swiss reference rock. In this study, this correction value dΔf was assessed by comparing empirical amplification observed at seismic stations and converted to amplification in intensity (Af), with the values of the macroseismic amplification map at the instrumented sites (ΔIm).
Most of the observed ΔIm used to derive the macroseismic amplification map refer to lower-grade intensities, below intensity VI (Fäh et al. 2011). At these intensities, no damage occurs, and intensity is best correlated with PGV and PGA (e.g. Omine et al. 2008). Therefore, observed Af derived from PGV and PGA might be preferred when compared to ΔIm. The dΔf due to the different soil/rock references is therefore measured best from PGV (0.42, 0.37; from Figs. 3 and 4) and PGA (0.56, 0.52; from Figs. 3 and 4). These values are in agreement with the constant correction of 0.47 or 1/2 (intensity units) suggested by Fäh et al. (2011). When we consider intensity grades in which damage to buildings is described (VI and above), PGA should preferably be weighted less than PGV and SA at the period of the buildings, to correct for the difference in reference soil/rock conditions. For longer periods (high-rise buildings), the influence of the deeper structure could be more relevant. The dΔf therefore becomes smaller with increasing periods. Moreover, it appears that the deeper structure is less reflected in the amplification derived from IDP. For the Swiss building stock, it is suggested that SA at 0.3 s (0.32, 0.31; from Figs. 3 and 4) together with PGV (0.42, 0.37; from Figs. 3 and 4) might be the best selection to correct for the difference in reference soil/rock conditions.
The reference soil conditions of the macroseismic amplification map have been assessed using different techniques. The IDP were subdivided in each geological/tectonic unit as in the macroseismic amplification map and plotted together with the average VS,30 values (Fig. 5). This analysis reveals that most of the IDP have a VS,30 in the range 258–687 m/s with an average value of 472 ± 214 m/s. This suggests that the map is derived using mostly observations from soil classes B and C. For this reason, the dΔf were also plotted versus building code SIA-261 (2014) soil classification, confirming that average dΔf for soil classes B and C are the closest to those found in this study. This corresponds to a VS,30 value in the range of about 400–600 m/s for the soil reference condition of the macroseismic amplification map. It was shown that the macroseismic amplification map has the tendency to provide too high values for non-weathered rock materials and too low values for the soft sediments in soil class D.
The VS,30 values obtained with the previous methods are slightly lower than 640 ± 58 m/s derived from the relationships between Af and VS,30 site proxy. Macroseismic amplification factors Af, derived from the measured empirical amplifications, were correlated in this approach with site response proxies, such as the quarter-wavelength velocity (VQWL) at 0.3 s, 0.5 s, and 1.0 s, and travel time averaged velocities (VS,Z). The results point out that the best correlations are obtained for SA at 0.3 s, PGV, and PGA. Using these relationships and the obtained dΔf, it was possible to retrieve an estimate of the soil reference condition proxies for the macroseismic amplification map in terms of VS,Z. In particular, the VS,30 value of the reference soil is about 640± 58 m/s. Using these different methods, we can also define a lower bound of 450 m/s and an upper bound of 700 m/s for VS,30 of the macroseismic amplification map soil reference. Uncertainties are high due to the properties of macroseismic intensity, as shown in Figs. 3, 5, and 10.
Finally, we assessed the statistical significance of the geological/tectonic classification of the macroseismic amplification map with respect to the empirical amplification data at instrumented sites. This analysis highlights that presently, it is not possible to evaluate systematically the significance of the geological/tectonic units in the macroseismic amplification map, basing the analysis on site response data collected at the available instrumented sites. The number of stations is in fact insufficient, and these are not evenly distributed among the various units. However, the analysis was carried out on a limited number of soil classes (7) in the macroseismic amplification map, evidencing that these classes host stations that generally show an internally consistent site response pattern; however, not necessarily all macroseismic units differ significantly in their average behaviour. This fact opens up to the possibility of reviewing the macroseismic amplification map by merging classes with similar behaviour or by defining a new classification scheme based also on other proxies besides geology and tectonics.
References
Bergamo P, Hammer C, and Fäh D. (2019) SERA WP7/NA5–task 7.4 towards improvement of site characterization indicators. Seismology and Earthquake Engineering Research Infrastructure Alliance for Europe (SERA) project, Deliverable D7.4. (http://www.sera-eu.org/en/Dissemination/deliverables/, last retrieved on 26.06.2020)
Boore DM (2003) 85.13 SMSIM: stochastic method simulation of ground motion from earthquakes. In: International Geophysics. pp 1631–1632
Carlino S, Cubellis E, Marturano A (2010) The catastrophic 1883 earthquake at the island of Ischia (Southern Italy): macroseismic data and the role of geological conditions. Nat Hazards 52:231–247. https://doi.org/10.1007/s11069-009-9367-2
Cauzzi C, Edwards B, Fäh D, Clinton J, Wiemer S, Kästli P, Cua G, Giardini D (2015) New predictive equations and site amplification estimates for the next-generation Swiss ShakeMaps. Geophys J Int 200:421–438. https://doi.org/10.1093/gji/ggu404
Edwards B, Fäh D (2013) Measurements of stress parameter and site attenuation from recordings of moderate to large earthquakes in Europe and the Middle East. Geophys J Int 194:1190–1202. https://doi.org/10.1093/gji/ggt158
Edwards B, Michel C, Poggi V, Fäh D (2013) Determination of site amplification from regional seismicity: application to the Swiss national seismic networks. Seismol Res Lett 84:611–621. https://doi.org/10.1785/0220120176
Faenza L, Michelini A (2010) Regression analysis of MCS intensity and ground motion parameters in Italy and its application in ShakeMap. Geophys J Int 180:1138–1152. https://doi.org/10.1111/j.1365-246X.2009.04467.x
Faenza L, Michelini A (2011) Regression analysis of MCS intensity and ground motion spectral accelerations (SAs) in Italy. Geophys J Int 186:1415–1430. https://doi.org/10.1111/j.1365-246X.2011.05125.x
Fäh D, Fritsche S, Poggi V, et al (2009) Determination of site information for seismic stations in Switzerland, Swiss Seismological Service technical report: SED/PRP/R/004/20090831
Fäh D, Giardini D, Kästli P, et al (2011) ECOS-09 earthquake catalogue of Switzerland release 2011. Report and database. Sed/Ecos/R/001/20110417
Field EH, Jacob KH (1995) A comparison and test of various site response estimation techniques, including three that are not reference site dependent. Bull Seismol Soc Am 85:1127–1143
Hobiger M, Fäh D, Scherrer C, et al (2017) The renewal project of the Swiss Strong Motion Network (SSMNet). In: Proceedings of the 16th World Conference on Earthquake engineering (16WCEE). Santiago de Chile, Chile
Kaestli P, Fäh D (2006) Rapid estimation of macroseismic effects and Shakemaps using macroseismic data. In: 1st European Conf. Earthquake Engineering and Seismology. Geneva, Switzerland, p 1535
Kaka SLI, Atkinson GM (2004) Relationships between instrumental ground-motion parameters and modified Mercalli intensity in eastern North America. Bull Seismol Soc Am 94:1728–1736. https://doi.org/10.1785/012003228
Michel C, Edwards B, Poggi V, Burjanek J, Roten D, Cauzzi C, Fah D (2014) Assessment of site effects in Alpine regions through systematic site characterization of seismic stations. Bull Seismol Soc Am 104:2809–2826. https://doi.org/10.1785/0120140097
Michel C, Fäh D, Edwards B, Cauzzi C (2017) Site amplification at the city scale in Basel (Switzerland) from geophysical site characterization and spectral modelling of recorded earthquakes. Phys Chem Earth, Parts A/B/C 98:27–40. https://doi.org/10.1016/j.pce.2016.07.005
Murphy BP, Chakravarti IM, Laha RG, Roy J (1968) Handbook of methods of applied statistics. Vol. I: Techniques of computation, descriptive methods and statistical inference. Appl Stat 17:293. https://doi.org/10.2307/2985652
Musson RMW, Grünthal G, Stucchi M (2010) The comparison of macroseismic intensity scales. J Seismol 14:413–428. https://doi.org/10.1007/s10950-009-9172-0
Omine H, Hayashi T, Yashiro H, Fukushima S (2008) Seismic risk analysis method using both PGA and PGV. In: Proceeding of the 14th World Conference on Earthquake Engineering. Beijing, China
Panzera F, D’Amico S, Lombardo G, Longo E (2016) Evaluation of building fundamental periods and effects of local geology on ground motion parameters in the Siracusa area, Italy. J Seismol 20:1001–1019. https://doi.org/10.1007/s10950-016-9577-5
Panzera F, Lombardo G, Imposa S, Grassi S, Gresta S, Catalano S, Romagnoli G, Tortorici G, Patti F, di Maio E (2018) Correlation between earthquake damage and seismic site effects: the study case of Lentini and Carlentini, Italy. Eng Geol 240:149–162. https://doi.org/10.1016/j.enggeo.2018.04.014
Pettenati F, Sirovich L (2007) Validation of intensity‐based source inversion of three destructive Californian earthquakes. Bull Seismol Soc Am. 97:1587–1606
Pettenati F, Sirovich L, Sandron D (2018) Modern techniques of treating damage patterns (intensity) to retrieve information on the 6 May 1976 M 6.4 earthquake. Boll Geof Teor 59(4):445–462. https://doi.org/10.4430/bgta0250
Poggi V, Burjánek J, Michel C, Fäh D (2017) Seismic site-response characterization of high-velocity sites using advanced geophysical techniques: application to the NAGRA-Net. Geophys J Int 210:645–659. https://doi.org/10.1093/gji/ggx192
Poggi V, Edwards B, Fäh D (2011) Derivation of a reference shear-wave velocity model from empirical site amplification. Bull Seismol Soc Am 101:258–274. https://doi.org/10.1785/0120100060
Roten D, Fäh D, Olsen KB, Giardini D (2008) A comparison of observed and simulated site response in the Rhône valley. Geophys J Int 173:958–978. https://doi.org/10.1111/j.1365-246X.2008.03774.x
Sbarra P, De Rubeis V, Di Luzio E et al (2012) Macroseismic effects highlight site response in Rome and its geological signature. Nat Hazards 62:425–443. https://doi.org/10.1007/s11069-012-0085-9
SIA-261 (2014). SIA 261 Azioni sulle strutture portanti. Compiled by: SIA (Società svizzera degli ingegneri e degli architetti) Copyright © 2014 by SIA Zurich
Sousa ML, Oliveira CS (1996) Hazard mapping based on macroseismic data considering the influence of geological conditions. Nat Hazards 14:207–225
Swisstopo (2005) Geological map of Switzerland 1:500 000. Compiled by: Geological Institute, University of Bern, and Federal Office for Water und Geology. ISBN number: 3–906723–39-9
Swisstopo (2020) The large-scale topographic landscape model of Switzerland swissTLM3D. https://shop.swisstopo.admin.ch/it/products/landscape/tlm3D
Wald DJ, Worden BC, Lin K, Pankow K (2005) ShakeMap manual: technical manual, user’s guide, and software guide. U. S. Geological Survey, Techniques and Methods 12-A1, pp. 132. https://doi.org/10.3133/tm12A1
Welch BL (1947) The generalization of ‘student’s’ problem when several different population variances are involved. Biometrika 34:28–35. https://doi.org/10.1093/biomet/34.1-2.28
Wiemer S, Danciu L, Edwards B, et al (2016) Seismic hazard model 2015 for Switzerland (SUIhaz2015)
Wu Y-M (2003) Relationship between peak ground acceleration, peak ground velocity, and intensity in Taiwan. Bull Seismol Soc Am 93:386–396. https://doi.org/10.1785/0120020097
Acknowledgements
The authors thank the Editors Prof. Dario Alberallo and Dr. Franco Pettenati and an anonymous reviewer, whose comments have greatly helped improve the article.
Funding
Open access funding provided by Swiss Federal Institute of Technology Zurich. This work was made in the frame of the Risk Model Switzerland project financed by contributions from the Swiss Federal Office for the Environment (FOEN), Swiss Federal Office for Civil Protection (FOCP), and Eidgenössische Technische Hochschule Zürich (ETHZ).
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Panzera, F., Bergamo, P. & Fäh, D. Reference soil condition for intensity prediction equations derived from seismological and geophysical data at seismic stations. J Seismol 25, 163–179 (2021). https://doi.org/10.1007/s10950-020-09962-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10950-020-09962-z