Abstract
The main problems for ultrasonic inspection of austenitic stainless steel welds are low signal to noise ratio (SNR) and detection accuracy, caused by anisotropic and heterogeneous material structure with bulky columnar crystal. In order to overcome the problems mentioned above, a linear frequency modulated (LFM) pulse with a large time-bandwidth product can be used as the exciting signal in the ultrasonic inspection of the austenitic stainless steel welds, which can both enhance the average transmitted power and increase the SNR and time resolution by pulse compression process. Therefore, the ultrasonic time-of-flight diffraction (TOFD) technique with the LFM excitation was carried out to realize an accurate sizing and locating detection in austenitic stainless steel welds. Compared with the conventional TOFD testing, the SNR can be increased 12–15 dB, and the measured accuracy is also enhanced obviously. Accordingly the measured depth error is less than 0.81 % and the length error is less than 2.5 %. The proposed method can both enhance the capabilities of the ultrasonic inspection of austenitic welds and the measurement accuracy of ultrasonic TOFD testing.
Similar content being viewed by others
References
Chassignole, B., Guerjouma, R.El, Ploix, M.A.: Ultrasonic and structural characterization of anisotropic stainless steel welds: towards a higher reliability in ultrasonic non-destructive testing. NDT & E Int. 43(4), 273–282 (2010)
Ogilvy, J.A.: Ultrasonic beam profiles and beam propagation in an austenitic weld using a theoretical ray tracing model. Ultrasonics 24(6), 337–347 (1986)
Harker, A.H., Ogilvy, J.A., Temple, J.A.G.: Modeling ultrasonic inspection of austenitic welds. J. Nondestruct. Eval. 9(2/3), 155–165 (1990)
Baek, E., Yim, H.: Numerical modeling and simulation for ultrasonic inspection of anisotropic austenitic welds using the mass-spring lattice model. NDT & E Int. 44(7), 571–582 (2011)
Spies, M., Rieder, H.: Synthetic aperture focusing of ultrasonic inspection data to enhance the probability of detection of defects in strongly attenuating materials. NDT & E Int. 43(5), 425–431 (2010)
Höhne, C., Kolkoori, S., Rahma, M.U., et al.: SAFT imaging of transverse cracks in austenitic and dissimilar welds. J. Nondestruct. Eval. 32(1), 51–66 (2013)
Praveen, A., Vijayarekha, K., Abraham, S.T., et al.: Signal quality enhancement using higher order wavelets for ultrasonic tofd signals from austenitic stainless steel welds. Ultrasonics 53(6), 1288–1292 (2013)
Mahaut, S., Godefroit, J.L., Roy, O., Cattiaux, G.: Application of phased array technique to coarse grain components inspection. Ultrasonics 42(1–9), 791–796 (2004)
Ye, J., Kim, H.J., Song, S.J., et al.: Model-based simulation of focused beam fields produced by a phased array ultrasonic transducer in dissimilar metal welds. NDT & E Int. 44(3), 290–296 (2011)
Lam, F., Szilard, J.: Pulse compression techniques in ultrasonic non-destructive testing. Ultrasonics 14(3), 111–114 (1976)
Jeong, J.S., Chang, J.H., Shung, K.K.: Pulse compression technique for simultaneous HIFU surgery and ultrasonic imaging: a preliminary study. Ultrasonics 52(6), 730–739 (2012)
Tanabe, M., Yamamura, T., Okubo, K., Tagawa, N.: Medical ultrasound imaging using pulse compression technique based on split and merge strategy. Jpn. J. Appl. Phys. 49(7), 07HF15 (2010)
Gan, T.H., Hutchins, D.A., Billson, D.R., et al.: The use of broadband acoustic transducers and pulse-compression techniques for air-coupled ultrasonic imaging. Ultrasonics 39(3), 181–194 (2001)
Gan, T.H., Hutchins, D.A., Green, R.J.: A swept frequency multiplication technique for air-coupled ultrasonic NDE. IEEE Trans. Ultrason. Ferroelectr. Freq. Control 51(10), 1271–1279 (2004)
Gan, T.H., Hutchins, D.A., Green, R.J., et al.: Noncontact, high-resolution ultrasonic imaging of wood samples using coded chirp waveforms. IEEE Trans. Ultrason. Ferroelectr. Freq. Control 52(2), 280–288 (2005)
Gang, T., Sheng, Z.Y., Tian, W.L.: Time resolution improvement of ultrasonic TOFD testing by pulse compression technique. Insight 54(4), 193–197 (2012)
Cong, S., Gang, T., Zhang, J.Y.: Parameter design of linear frequency modulated excitation waveform for ultrasonic nondestructive testing of metallic materials. J. Nondestruct. Eval. 33(4), 684–693 (2014)
Levanon, N., Mozeson, E.: Radar Signals, pp 24–28, pp 54–67. Wiley, New York (2004)
Charlesworth, J.P., Temple, J.A.G.: Engineering Applications of Ultrasonic Time-of-Flight Diffraction, 2nd edn., pp 20–40, pp 93–101, pp 207–210. Research Studies Press, Somerest (2001)
Chen, T.L., Que, P.W., Zhang, Q., et al.: Ultrasonic nondestructive testing accurate sizing and locating technique based on time-of-flight-diffraction method. Russ. J. Nondestruct. Test. 41(9), 57–68 (2005)
Acknowledgments
Projects(51175113, 51105033) supported by Natural Science Foundation of China, international cooperation project (2007DFR70070).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Cong, S., Gang, T. & Zhang, Jy. Ultrasonic Time-of-Flight Diffraction Testing with Linear Frequency Modulated Excitation for Austenitic Stainless Steel Welds. J Nondestruct Eval 34, 8 (2015). https://doi.org/10.1007/s10921-015-0281-0
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s10921-015-0281-0