Abstract
The present work addresses a facile synthesis of Indium doped zinc oxide (IZO) cellulose acetate nanocomposite membrane. The membrane was prepared by casting method. Various weights of In:ZnO nanoparticles were added to solution formed by dissolution of cellulose acetate granules in acetone. The harvested membrane, after acetone evaporation, was characterized by various techniques including X ray diffraction, scanning electron microscopy, energy dispersive X ray and elemental mapping, Fourier transform infrared spectroscopy. The results show that the In:ZnO nanoparticles are well embedded in the cellulose acetate host matrix. The elemental mapping reveals that the nanoparticles are uniformly distributed. The optical characterization reveals the reduction of the transmittance in the UV (A and B range) of the CA/IZO composite with increasing the weight of the added IZO powder. This reduction was attributed to ZnO UV absorption. No noticeable peak assigned to ZnO bond are observed. However, IR peaks are shifted towards the higher wavenumber due to the change of the bonds environment with including IZO in the CA matrix. The antibacterial action of the synthetized nanocomposite membranes was tested against Escherichia coli (E. coli). Staphylococcus aureus (S. aureus). The assay results have shown that the membrane has no activity against (E. coli). In contrary, the synthetized membrane exhibits an interesting antibacterial activity against S. aureus. The inhibition region varies from 6 to 15 mm with increasing the weight ratio of filler. A zone of inhibition (ZOI) of 18 mm was observed for the membrane prepared with 30% wt. of In:ZnO. We noticed that the ZOI radius increases with the added weight of IZO. Due the settling down of the nanoparticles only one face of the membrane exhibits an antibacterial activity.
Similar content being viewed by others
Change history
12 September 2022
A Correction to this paper has been published: https://doi.org/10.1007/s10904-022-02477-9
References
L.E. Aguilar, A. Ghavami Nejad, C.H. Park, C.S. Kim, Nanomedicine 13(2), 527 (2017)
G. El-Barbary, M.K. Ahmed, M.M. El-Desoky, A.M. Al-Enizi, A.A. Alothman, A.M. Alotaibi, A. Nafady, Synth. Met. 278, 116824 (2021)
S. Beis, S. Monteiro, R. Santos, A.S. Figueiredo, M. Guadalupe, M. Sanchez-Loredo, M.A. Lemos, F. Lemos, M. Minhalma, M. Norberta de Pinho, Water Res. 149, 225 (2019)
Y. Wu, G. Xu, W. Zhang, C. Song, L. Wang, X. Fang, L. Xu, S. Han, J. Cui, L. Gan, Carbohydr. Polym. 267, 118166 (2021)
J. Lostea, J.-M. Lopez-Cuesta, L. Billona, H. Garay, M. Save, Progress Polym. Sci. 89, 133 (2019)
M. Abbas, M. Buntinx, W. Deferme, R. Peeters, Nanomaterials 9, 1494 (2019)
M. Choi, G. Murillo, S. Hwang, J.W. Kim, J.H. Jung, C.Y. Chen, M. Lee, Nano Energy 33, 462 (2017)
E. Tang, S. Dong, Colloids Polym. Sci. 287, 1025 (2009)
S. Tachikawa, A. Noguchi, T. Tsuge, M. Hara, O. Odawara, H. Wada, Materials 4, 1132 (2011)
S. Li, M.M. Lin, M.S. Toprak, D.K. Kim, M. Muhammed, Nano Rev. 1, 1 (2010)
S. Zinatloo-Ajabshir, S.A. Heidari-Asil, M. Salavati-Niasari, Sep. Purif. Technol. 280(1), 119841 (2022)
H. Etemadi, S. Afsharkia, S. Zinatloo-Ajabshir, E. Shokri, Polym. Eng. Sci. 61, 2364–2375 (2021)
S. Zinatloo-Ajabshir, M. Mousavi-Kamazani, Ceram. Int. 47(17), 23702–23724 (2021)
H. Safajou, M. Ghanbari, O. Amiri, H. Khojasteh, F. Namvar, S. Zinatloo-Ajabshir, M. Salavati-Niasari, Int. J. Hydrogen Energy 46(39), 20534–20546 (2021)
S. Sharaf, M.E. El-Naggar, Cellulose 25(9), 5195–5204 (2018)
M.S. Abdelrahman, T.A. Khattab, A. Aldalbahi, M.R. Hatshan, M.E. El-Naggar, J. Environ. Chem. Eng. (2020). https://doi.org/10.1016/j.jece.2020.104573
A. Aldalbahi, M.E. El-Naggar, M.K. Ahmed, G. Periyasami, M. Rahaman, A.A. Menazea, J. Mater. Res. Technol. 9, 15045 (2020)
A. Aldalbahi, M. El-Naggar, T. Khattab, M. Abdelrahman, M. Rahaman, A. Alrehaili, M. El-Newehy, Polymers 12, 2501 (2020)
A. Abdel-Karim, M.E. El-Naggar, E.K. Radwan, I.M. Mohamed, M. Azaam, E.R. Kenawy, Chem. Eng. J. 405, 126964 (2021)
A. Zucchelli, M.L. Focarete, C. Gualandi, S. Ramakrishna, Polym. Adv. Technol. 22, 339–349 (2011)
A.R. Unnithan, G. Gnanasekaran, Y. Sathishkumar, Y.S. Lee, C.S. Kim, Carbohydr. Polym. 102, 884 (2014)
T.J. Sill, H.A. von Recum, Biomaterials 29, 1989 (2008)
S. Tungprapa, I. Jangchud, P. Supaphol, Polymer 48, 5030 (2007)
T.P. Armedya, M.F. Dzikri, S.C.W. Sakti, A. Abdulloh, Y. Raharjo, S. Wafiroh, M.Z. Fahmi, BioNanoScience 9, 274 (2019)
A.W. Jatoi, Z. Khatri, F. Ahmed, M.H. Memon, J. Surf. Deterg. 18, 205 (2015)
A. W., Jatoi, I. S. Kim, and Q.Q. Ni, Appl. Nanoscience, 1 (2018)10.
H. Lee, A.W. Jatoi, Y. Kyohei, K.-O. Kim, K.H. Song, J. Lee, Text. Res. J. 88, 630 (2018)
A.R. Unnithan, G. Gnanasekaran, Y. Sathishkumar, Y.S. Lee, C.S. Kim, Carbohyd. Polym. 102, 884 (2014)
S.K. Nethi, S. Das, C.R. Patra, S. Mukherjee, Biomater. Sci. 7, 2652 (2019)
S. Subhadarshini, R. Singh, D.K. Goswami, A.K. Das, N.C. Das, Langmuir 35(52), 17166–17176 (2019)
S. Subhadarshini, R. Singh, A. Mandal, S. Roy, S. Mandal, S. Mallik, D.K. Goswami, A.K. Das, N.C. Das, Langmuir 37(31), 9356–9370 (2021)
S. Subhadarshini, E. Pavitra, G.S.R. Raju, N.R. Chodankar, D.K. Goswami, Y.-K. Han, Y.S. Huh, NCh. Das, A.C.S. Appl, Mater. Interfaces 12(26), 29302–29315 (2020)
S. Subhadarshini, E. Pavitra, G.S.R. Ma Raju, N.R. Chodankar, A. Mandal, S. Roy, S. Mandal, M.V. Basaveswara Rao, D.K. Goswami, Y. Suk Huh, N.C. Das, Ceram. Int. 47(11), 15293–15306 (2021)
S. Beisl, S. Monteiro, R. Santos, A.S. Figueiredo, M.G. Sanchez-Loredo, M.A. Lemos, F. Lemos, M. Minhalma, M. Norberta de Pinho, Synth. Met. 278, 116824 (2021)
M.R. Amin, M.A. Chowdhury, M.A. Kowser, Heliyon 5, 02009 (2019)
S.I. Al-Saeedi, N.S. Al-Kadhi, G.M. Al-Senani, O.A. Almaghrabi, A. Nafady, Int. J. Biol. Macromol. 182, 464 (2021)
A.W. Jatoi, H. Ogasawara, I.S. Kim, Q.Q. Ni, Mater. Sci. Eng. C 110, 110679 (2020)
J.R. Ricardo, I.P. Matos, C. Chaparro, J.C. Silva, M.A. Valente, J.P. Borges, P.I. Soares, Carbohydr. Polym. 198, 9 (2018)
M.K. Ahmed, A.A. Menazea, A.M. Abdelghany, Int. J. Biol. Macromol. 155, 636 (2020)
A.A. Aly, M.K. Ahmed, Int. J. Pharm. 598, 120325 (2021)
M.Z. Fahmi, R.A. Prasetya, M.F. Dzikri, S. Candra, W. Sakti, B. Yuliarto, I. Ferdiansjah, Mater. Chem. Phys. 250, 123055 (2020)
Z. Kalaycıoğlu, N. Kahya, V. Adımcılar, H. Kaygusuz, E. Torlak, G. Akın-Evingür, F.B. Erim, Eur. Polym. J. 133, 109777 (2020)
A.A. Badawy, A.F. Ghanem, M.A. Yassin, A.M. Youssef, M.H. Abdel Rehim, Environ. Nanotechnol. Monit. Manage. 16, 0501 (2021)
M.K. Haider, A. Ullah, M. Nauman Sarwar, Y. Saito, L. Suna, S. Park, I.S. Kim, Int J. Biol. Macromol. 173, 315–326 (2021)
Z. Lu, J. Gao, Q. He, J. Wu, D. Liang, H. Yang, Carbohydr. Polym. 156, 460 (2017)
P.K. Dutta, S. Tripathi, G.K. Mehrotra, J. Dutta, Food Chem. 114, 1173 (2009)
I.S. Elashmawi, E.M. Abdelrazek, A.M. Hezma, A. Rajeh, Phys. B Condens. Matter 434, 57 (2014)
E.M. Abdelrazek, I.S. Elashmawi, A. Hezma, A. Rajeh, Int. J. Modern Appl. Phys. 1, 83 (2012)
S.M. Hassan, A.I. Ahmed, M.A. Mannaa, Ceram. Int. 44, 6201 (2018)
R. Brayner, R. Ferrari-Iliou, N. Brivois, S. Djediat, M.F. Benedetti, F. Fievet, Nano Lett. 6, 866 (2006)
G.X. Tong, F.F. Du, Y. Liang, Q. Hu, R.N. Wu, J.G. Guan, X. Hu, J. Mater. Chem. B 1, 454 (2013)
R.R. Krishna, T.K. Ranjit, C.M. Adhar, Langmuir 27, 4020 (2011)
J. Nicole, R. Binata, T.R. Koodali, C.M. Adhar, Microbiol. Lett. 279, 71 (2008)
M.E. Culica, A.L. Chibac-Scutaru, V. Melinte, S. Coseri, Materials 13, 2955 (2020). https://doi.org/10.3390/ma13132955
K. Ravichandrana, R. Rathia, M. Banetoc, K. Karthikaa, P.V. Rajkumara, B. Sakthivela, R. Damodaran, Ceram. Int. 41, 3390 (2015)
S. Anithaa, S. Muthukumaran, Mater. Sci. Eng. C 108, 110387 (2020)
Acknowledgements
This research work was funded by institutional Fund Projects under Grant number (IFPRC-197-130-2020). Therefore, authors gratefully acknowledge technical and financial support from the Ministry of Education and King Abdulaziz University, Jeddah Saudi Arabia.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no conflict of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
The original version of this article was revised: The original version of this article unfortunately contained two mistakes. The co-author N.H. Alonizan is affiliated only to the following institution:
Department of Physics, College of Science, Imam Abdulrahman Bin Faisal University, P.O. Box 1982, Dammam, 31441, Saudi Arabia.
The grant number in the Acknowledgments section should be IFPRC-197-130-2020. The Acknowledgments section should read as follows:
Acknowledgments
This research work was funded by institutional Fund Projects under Grant number (IFPRC-197-130-2020). Therefore, authors gratefully acknowledge technical and financial support from the Ministry of Education and King Abdulaziz University, Jeddah Saudi Arabia.
The original article was corrected.
Rights and permissions
Springer Nature or its licensor holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Aida, M.S., Alonizan, N.H., Hussein, M.A. et al. Facile Synthesis and Antibacterial Activity of Bioplastic Membrane Containing In Doped ZnO/Cellulose Acetate Nanocomposite. J Inorg Organomet Polym 32, 1223–1233 (2022). https://doi.org/10.1007/s10904-021-02171-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10904-021-02171-2