Abstract
The Alborz tokamak is a D-shape cross section tokamak that is under construction in Amirkabir University of Technology. The most important part of the tokamak design is the design of TF coils. In this paper a refined design of the TF coil system for the Alborz tokamak is presented. This design is based on cooper cable conductor with 5 cm width and 6 mm thickness. The TF coil system is consist of 16 rectangular shape coils, that makes the magnetic field of 0.7 T at the plasma center. The stored energy in total is 160 kJ, and the power supply used in this system is a capacitor bank with capacity of C = 1.32 mF and V max = 14 kV.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
The tokamak is a toroidal plasma confinement system, the plasma being confined by a magnetic field. The principal magnetic field is the toroidal magnetic field [1]. Alborz tokamak is a D-shape cross section tokamak and the most important part of the design of this tokamak is the design of TF coils and its power supply.
Some tokamaks has circular cross section [2, 3] but many of advanced tokamaks have typically D-shape or non-circular cross section [4–19] and some of them has superconducting field coils [12–20].
In this paper we are present the design of TF coils and give the major parameters of tokamak like major radius, maximum plasma current, number of TF coils, number of total turns and current per turn for a non-circular cross section TF coil. And we assume that some of the parameters like maximum current carrying by the cooper cable, the capacity of the power supply, maximum operational voltage, required safety factor, aspect ratio and the cross section shape of vacuum vessel and the toroidal magnetic field in plasma center, are known.
In addition we must consider about the magnetic field ripple. The magnetic field ripple is inversely proportional to the number of TF coils and by increase of their number is decreased [21]. Number of TF coils is normally about 12–36 coils [22, 23]. The ripple magnitude due to the finite number of TF coils and the size of the ports of vacuum vessel, determine the number, size and shape of TF coils [24]. Axisymmetry of magnetic field topology insures good classical particle confinement. However, due to discreteness of the TF coil system, it is unavoidable to have some ripple component in the toroidal magnetic field [24, 25].
The TF coils are wound around the vacuum vessel. The vacuum vessel provides a suitable condition for plasma shaping, baking, confinement, stability and supervising [22, 23, 26].
In some tokamaks for investigate of toroidal field behavior, use a detailed Finite Element Method (FEM) [7, 27–29] and in this paper we use a detailed 3D finite element method for all component of TF coils.
Calculation of Major and Minor Radius and Turn Numbers of TF Coils
At first we consider about the assumptions. The goal is the design of a tokamak with D-shape cross section, that has a aspect ratio of 3 (A = R/a = 3). We expect that the toroidal magnetic field at the center of the vacuum vessel is 0.7 T. The power supply used in this system is a capacitor bank of 1.32 mF, and V max = 14 kV that has energy of \( E = \frac{1}{2} \) CV 2 = 129 kJ. Currently, the range of safety factor on the edge of plasma for stable operation of tokamaks is usually between 3 and 4, while it takes on a minimum value of unity at the axis of plasma due to nonlinear sawtooth oscillation [30]. To satisfy this criteria, we set the safety factor 3 (q = 3). The coil material is cooper and it’s area is 5 cm × 6 mm, that can carry 12 kA of transient current, that is I max = 12 kA. Thus the circuit diagram of power supply and TF coils is depicted in Fig. 1, that V is the power supply voltage.
After switch S is closed, the stored energy in C transfer to L, and gives
for C = 1.32 mF, V max = 14 kV, I max = 12 kA, gives
and the cycle period is
The magnetic field inside a toroidal solenoid is
B T is toroidal magnetic field, N is the number of turns, I is turn’s current, and R is major radius.
By substitution of I = 12 kA, B T = 0.7 T, and R = 3a gives
and the inductance of a toroidal coil with N turn is
where r is minor radius of coil. For insulation and assembly pieces and to avoid of sharp variation of magnetic field of adjacent coils, we put a distance of 5 cm between coils and vacuum vessel. And since the width of cable is 5 cm, the minor radius of TF coils is
as depicted in Fig. 2.
Thus
by substituting of (1) in (2) gives
Winding of TF Coils
By attention to major and minor radius of vacuum vessel and the width of cables (5 cm), the schematic of the vacuum vessel as viewed from above is depicted in Fig. 2. By consideration of ports for diagnostic and vacuum systems, and gas injection, we must arrange the TF coils to n group. Because the requirement port diameter is about 10 cm and by consider to its caps and junctions, we need 14 cm width and width of a cable is about 9 mm. The circumference of outer side of vacuum vessel is 2π × 0.6 m. then
Thus the number of coils is 16 and the number of turns per coils is 10.
The schematic of TF coils is depicted in Fig. 3.
We must consider that every coil consist of 10 turns.
Calculation of Plasma Current
By writing Ampere’s law [1] in the form
That B θ is poloidal magnetic field and I p (r) is plasma current
That j(r′) is the current density inside r, and by using the
And taking r = a, the edge value of q is
By substituting of values for this tokamak, for q = 3, the maximum value of I p is
The parameters of Alborz tokamak are shown in Table 1.
Simulation of Toroidal Magnetic Field
Cross section of TF coils is depicted in Fig. 2. Here we simulate the toroidal magnetic field by FEM (Finite Element Method). By using this method, the shape of toroidal magnetic field is as Fig. 4.
Figure 5 illustrated the toroidal magnetic field in 0′ and 11.25′. (a) is in 0′ and (b) is in 11.25′, that is between coils.
The average magnetic field through 360 degree is as Fig. 6 that varies by 1/R.
Toroidal field in R o = 0.45 m is 0.85 T.
Summary
By using of capacitor bank of C = 1.32 mF and V max = 14 kV as toroidal coils power supply, and by consider of cooper coils with area of 0.05 × 0.006 m2, we gives I max = 12 kA, that gives a tokamak with R o = 0.45 m, a = 0.15 m, and B T = 0.85 T. This tokamak is under construction in Amirkabir university of technology. The expected parameters of this tokamak is shown in Table 2.
References
J. Wesson, Tokamaks (Clarendon, Oxford, 2004)
V.P. Smirnov, Nucl. Fusion 50, 014003 (2010). doi:10.1088/0029-5515/50/1/014003
O. Neubauer et al., Fusion Sci. Technol. 47 (2005)
J.A. Schmidt, IEEE (1995)
G.H. Neilson et al., IEEE (1994)
J.L. Luxon, Nucl. Fusion 42, 614–633 (2002)
D.A. Gates et al., Fusion Eng. Des. 86, 41–44 (2011)
S.O. Dean et al., J. Fusion Energ. 17(4) (1998)
J. A. Schmidt et al., J. Fusion Energ. 12(3) (1993)
G.H. Neilson et al., J. Fusion Energ. 18(3) (1999)
J.D. Callen et al., J. Fusion Energ. 15(3/4) (1996)
E. Salpietro et al., Fusion Eng. Des. 46, 151–158 (1999)
W. Chen et al., Fusion Eng. Des. 83, 45–49 (2008)
G. Calabro et al., Fusion Eng. Des. 84, 522–525 (2009)
H.K. Park et al., Fusion Eng. Des. 85, 1981–1985 (2010)
B.C. Kim et al., Fusion Eng. Des. 83, 573–579 (2008)
D.M. Gao et al., IEEE (1994)
G.S. Lee et al., Nucl. Fusion, 41(10) (2001)
G.S. Lee et al., Fusion Eng. Des. 46, 405–411 (1999)
W.T. Reiersen et al., IEEE (1998)
F. Bellina et al., IEEE Trans. Magn. 24(2) (1988)
V.A. Krylov et al., Fusion Eng. Des. 56–57, 825–829 (2001)
V.A. Korotkov et al., Fusion Eng. Des. 56–57, 831–835 (2001)
B.J.Lee et al., IEEE (1998)
B. Lee et al., Fusion Technol. 36 (1999)
R.E. Rocco, IEEE (1995)
A.M. Miri et al., IEEE 467 (1999)
Y. Krivchenkov et al., IEEE (1996)
R.L. Myatt, IEEE Trans. Magn. 30(4) (1984)
F. Dini et al., J. Fusion Energ. 28, 282–289 (2009)
Open Access
This article is distributed under the terms of the Creative Commons Attribution Noncommercial License which permits any noncommercial use, distribution, and reproduction in any medium, provided the original author(s) and source are credited.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This is an open access article distributed under the terms of the Creative Commons Attribution Noncommercial License (https://creativecommons.org/licenses/by-nc/2.0), which permits any noncommercial use, distribution, and reproduction in any medium, provided the original author(s) and source are credited.
About this article
Cite this article
Mardani, M., Amrollahi, R. & Saramad, S. Preliminary Design of Alborz Tokamak. J Fusion Energ 31, 175–178 (2012). https://doi.org/10.1007/s10894-011-9449-5
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10894-011-9449-5