Abstract
Investigations of the surface physicochemical properties of polylactic acid and polylactic acid/hydroxyapatite composite in a 70/30 ratio modified by atmospheric pressure low-temperature glow discharge argon plasma with the pulse duration of 1 μs and 5 μs and repetition rate of 100 kHz are described. Plasma modification of such materials may significantly affect physicochemical properties of surface. The polymerization of l-lactide was carried out at a temperature of 155 °C for 6 h. X-ray diffraction analysis shows that the degree of crystallinity of polylactic acid and composites based on polylactic acid/hydroxyapatite composite increases after plasma treatment due to polymer chain disruption. Infrared spectroscopy indicates that the –C=O absorption band intensity increases with plasma pulse duration, in turn indicating oxidation processes occurring in the polylactic acid surface layers. The wettability characteristics of the materials are improved by the plasma treatment, resulting in decreased water, glycerol, and ethylene glycol contact angle, and enhanced free surface energy.
Similar content being viewed by others
References
Pukhova IV (2015) The effect of ion implantation on the surface polymer dielectric resistance. Reports of Tomsk State University of Control Systems and Radioelectronics, vol 38, pp 79–82 (in Russian)
Garlotta D (2001) A literature review of poly(lactic acid). J Polym Environ 9:63–84. https://doi.org/10.1023/A:1020200822435
Mehta R, Kumar V, Bhunia H, Upadhyay SN (2005) Synthesis of poly(lactic acid): a review. J Macromol Sci Part C 45:325–349. https://doi.org/10.1080/15321790500304148
Ma Z, Gao C, Ji J, Shen J (2002) Protein immobilization on the surface of poly-l-lactic acid films for improvement of cellular interactions. Eur Polym J 38:2279–2284. https://doi.org/10.1016/S0014-3057(02)00119-2
Ng HM, Bee ST, Ratnam CT, Sin LT, Phang YY, Tee TT, Rahmat AR (2014) Effectiveness of trimethylopropane trimethacrylate for the electron-beam-irradiation-induced cross-linking of polylactic acid. Nuclear Instrum Methods Phys B 319:62–70. https://doi.org/10.1016/j.nimb.2013.10.027
Loo JSC, Ooi CP, Boey FYC (2005) Degradation of poly (lactide-coglycolide) (PLGA) and poly(-lactide) (PLA) by electron beam radiation. Biomaterials 26:1359–1367. https://doi.org/10.1016/j.biomaterials.2004.05.001
Izdebska-Podsiadły J, Dorsam E (2017) Effects of argon low temperature plasma on PLA film surface and aging behaviors. Vacuum 145:278–284. https://doi.org/10.1016/j.vacuum.2017.09.001
Techaikool P, Daranarong D, Kongsuk J, Boonyawan D, Haron N, Harley WS, Thomson KA, Foster J, Punyodom W (2017) Effects of plasma treatment on biocompatibility of poly[(l-lactide)-co-(ε-caprolactone)] and poly[(l-lactide)-co-glycolide] electrospun nanofibrous membranes. Soc Chem Ind 66:1640–1650. https://doi.org/10.1002/pi.5427
Moraczewski K, Mroz W, Budner B, Malinowski R, Zenkiewicz M (2016) Laser modification of polylactide surface layer prior autocatalytic metallization. Surf Coat Technol 304:68–75. https://doi.org/10.1016/j.surfcoat.2016.06.085
Zaidi L, Bruzaud S, Kaci M, Boumaud A, Gautier N, Grohens Y (2013) The effects of gamma irradiation on the morphology and properties of polylactide/Cloisite 30B nanocomposites. Polym Degrad Stab 98:341–348. https://doi.org/10.1016/j.polymdegradstab.2012.09.014
Chen JP, Su CH (2011) Surface modification of electrospun PLLA nanofibers by plasma treatment and cationized gelatin immobilization for cartilage tissue engineering. Acta Biomater 7:234–243. https://doi.org/10.1016/j.actbio.2010.08.015
Ho MH, Lee JJ, Fan SC, Wang DM, Hou LT, Hsieh HJ, Lai JY (2007) Efficient modification on PLLA by ozone treatment for biomedical applications. Macromol Biosci 7:467–474. https://doi.org/10.1002/mabi.200600241
Bartolo P, Kruth JP, Silva J, Levy G, Malshe A, Rajurkar K, Mitsuishi M, Ciurana J, Leu M (2012) Biomedical production of implants by additive electro-chemical and physical processes. CIRP Ann Manuf Technol 61:635–655. https://doi.org/10.1016/j.cirp.2012.05.005
Sviridov DV (2003) Ion implantation in polymers: chemical aspects, chemical problems of the development of new. Mater Technol 1:88–106
Popok VN (2012) Ion implantation of polymers: formation of nanoparticulate materials. Rev Adv Mater Sci 30:1–26
Tóth A, Kereszturi K, Mohai M, Bertóti I (2010) Plasma based ion implantation of engineering polymers. Surf Coat Technol 204:2898–2908. https://doi.org/10.1016/j.surfcoat.2009.12.004
Schiller TL, Sheeja D, McKenzie DR, McCulloch DG, Lau DSP, Burn S, Tay BK (2004) Plasma immersion ion implantation of poly(tetrafluoroethylene). Surf Coat Technol 483:177–178. https://doi.org/10.1016/S0257-8972(03)00916-2
Slepickova Kasalkova N, Slepicka P, Bacakova L, Sajdl P, Svorcik V (2013) Biocompatibility of plasma nanostructured biopolymers. Nucl Instrum Methods Phys Res 307:642–646. https://doi.org/10.1016/j.nimb.2012.10.035
Khorasani MT, Mirzadeh H, Irani S (2008) Plasma surface modification of poly (l-lactic acid) and poly (lactic-co-glycolic acid) films for improvement of nerve cells adhesion. Radiat Phys Chem 77:280–287. https://doi.org/10.1016/j.radphyschem.2007.05.013
Sokullu-Urkac E, Oztarhan A, Tihminlioglu F, Nikolaev A, Brown I (2012) Oxidation behavior of C- and Au-ion-implanted biodegradable polymers. IEEE Trans Plasma Sci 40:863–869. https://doi.org/10.1109/TPS.2011.2179677
Gao M, Sun L, Guo Y, Shi J, Zhang J (2017) Modification of polyethylene terephthalate (PET) films surface with gradient roughness and homogenous surface chemistry by dielectric barrier discharge plasma. Chem Phys Letters 689:179–184. https://doi.org/10.1016/j.cplett.2017.10.009
Song AY, Oh YA, Roh SH, Kim JH, Min SC (2015) Cold oxygen plasma treatments for the improvement of the physicochemical and biodegradable properties of polylactic acid films for food packaging. Food Eng Mater Sci 81:86–96. https://doi.org/10.1111/1750-3841.13172
Tverdokhlebov SI, Bolbasov EN, Shesterikov EV, Antonov LV, Golovkin AS, Matveev VG, Petlin DG, Anissimov YG (2015) Modification of polylactic acid surface using RF plasma discharge with sputter deposition of a hydroxyapatite target for increased biocompatibility. Appl Surf Sci 329:32–39. https://doi.org/10.1016/j.apsusc.2014.12.127
Gordeeva OS, Botvin VV, Filimoshkin AG (2015) Synthesis of oligomers from l-lactic acids and lactide from these oligomers. In: Multifunctional chemical materials and technologies, International scientific conference vol 2, pp 71–73
YeG Shapovalova, Ly’tkina DN, Kurzina IA, Kzhy’shkovska YG (2016) Preparation of biocompatible composites based on poly-l-lactide/hydroxyapatite and investigation of their anti-inflammatory activity. Key Eng Mater 683:475–480. https://doi.org/10.4028/www.scientific.net/KEM.683.475
Korotchenko NM, Rasskazova LA (2014) The method of obtaining silicon-modified hydroxyapatite using microwave radiation (NR TSU) Ru 2507151 (in Russian)
Syusyukina VA, Shapovalova YG, Korotchenko NM, Kurzina IA (2017) Structural-phase state and surface properties of composite materials based on polylactide and hydroxyapatite. Russ J Appl Chem 90:106–112. https://doi.org/10.1134/S1070427217010165
Savkin KP, Bugaev AS, Vizir AV, Gushenets VI, Nikolaev AG, Oks EM, Puhova IV, Frolova VP, Shandrikov MV, Yushkov GY (2016) Atmospheric plasma generator based on the discharge in argon flow. In: International congress on energy fluxes and radiation effects conference proceedings, vol 157, p 193
Savkin KP, Nikolaev AG, Vizir AV, Oks EM, Yushkov GYu, Shandrikov MV, Frolova VP, Vasenina IV (2018) Atmospheric pressure discharge plasma source for biocompatible polymers treatment. Russ Phys J 728:13–17 (in Russian)
Inagaki M, Kang F (2016) Materials science and engineering of carbon characterization. Elsevier, London, pp 153–173
Bico J, Thiele U, Quere D (2002) Wetting of textured surfaces. Colloids Surf 206:41–46. https://doi.org/10.1016/S0927-7757(02)00061-4
Yang J, Wan Y, Yang J, Bei J, Wang S (2003) Plasma-treated, collagen-anchored polylactone: its cell affinity evaluation under shear or shear-free conditions. J Biomed Mater Res 67A:1139–1147. https://doi.org/10.1002/jbm.a.10034
Shen H, Hu X, Yang F, Bei J, Wang S (2007) Combining oxygen plasma treatment with anchorage of cationized gelatin for enhancing cell affinity of poly(lactide-co-glycolide). Biomaterials 28:4219–4230. https://doi.org/10.1016/j.biomaterials.2007.06.004
Guerrouani N, Baldo A, Bouffin A, Drakides C, Guimon MF, Allylamine AM (2007) Plasma-polymerization on PLLA surface evaluation of the biodegradation. J Appl Polym Sci 105:1978–1986. https://doi.org/10.1002/app.26388
Beamson G, Briggs D (1992) High resolution XPS of organic polymers. Wiley, Chichester
Kondyurin A, Bilek M (2008) Ion beam treatment of polymers. Elsevier, London
Bohner M (2000) Calcium orthophosphates in medicine: from ceramics to calcium phosphate cements. Injury 31:37–47. https://doi.org/10.1016/S0020-1383(00)80022-4
Layrolle P (1998) Sol–gel synthesis of amorphous calcium phosphate and sintering into microporous hydroxyapatite bioceramics. J Am Ceram Soc 81:1421–1428. https://doi.org/10.1111/j.1151-2916.1998.tb02499.x
Legeros RZ, Lin S, Rohanizadeh R, Mijares D, Legeros JP (2003) Biphasic calcium phosphate bioceramics: preparation, properties and applications. J Mater Sci Mater Med 14:201–209. https://doi.org/10.4028/www.scientific.net/kem.240-242.473
Averyanova M, Bertrand P, Verquin B (2011) Manufacture of Co-Cr dental crowns and bridges by selective laser melting technology. Virtual Phys Prototype 6:179–185. https://doi.org/10.1080/17452759.2011.619083
Nakamoto K (2008) Infrared and Raman spectra of inorganic and coordination compounds. Wiley, New York
Chichti E, Henrion G, Cleymand F, Jamshidian M, Linder M, Arab-Tehrany E (2013) Effects of Ar–N2–O2 microwave plasma on poly-l-lactic acid thin films designed for tissue engineering. Plasma Process Polym 10:535–543. https://doi.org/10.1002/ppap.201200124
Pankaj SK, Bueno-Ferrer C, Misra NN, O’Neill L, Jiménez A, Bourke P, Cullen PJ (2014) Characterization of polylactic acid films for food packaging as affected by dielectric barrier discharge atmospheric plasma. Innov Food Sci Emerg Technol 21:107–113. https://doi.org/10.1016/j.ifset.2013.10.007
Tenn N, Follain N, Fatyeyeva K, Poncin-Epaillard F, Labrugere C, Marais S (2014) Impact of hydrophobic plasma treatments on the barrier properties of poly(lactic acid) films. RSC Adv 4:5626–5637. https://doi.org/10.1039/C3RA45323E
Acknowledgements
This work was supported by the Tomsk State University Competitiveness Improvement Program under Grant. Special thanks are extended to the Center for Collective Use at National Research Tomsk State University, the Nanomaterials and Nanotechnologies Research Centre at National Research Tomsk Polytechnic University, and the Thin Films Laboratory of the Institute of Physics of the University of São Paulo, Brazil.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that there is no conflict of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Laput, O., Vasenina, I., Salvadori, M.C. et al. Low-temperature plasma treatment of polylactic acid and PLA/HA composite material. J Mater Sci 54, 11726–11738 (2019). https://doi.org/10.1007/s10853-019-03693-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10853-019-03693-4