Abstract
This paper describes the preparation of crack-free stainless steel 316L/alumina functionally graded material (SUS316L/Al2O3 FGM) by spark plasma sintering (SPS). The sintering of individual powders and their composites was first studied to find an optimum SPS condition to get both materials and their mixtures highly dense. Sintering of cylindrical-shaped FGM pellets (ϕ20 mm) with various numbers of interlayers of 1, 2, 3, 4, and 9 was then carried out where the kind of and location of related cracking were carefully examined. The FGMs faced the problem of cracking mainly in the radial direction near the Al2O3-rich layers regardless of the number of layers or the gradient compositional profile. An yttrium-stabilized zirconia (3Y-ZrO2) was added thereafter to the gradient on the expense of Al2O3 content (up to 50 vol.%) and no radial cracking was found. Defects-free FGM pellets were successfully produced by interposing 19 interlayers between the SUS316L and Al2O3 ends. The Vickers hardness profile was determined throughout the cross-section of sintered FGM and it was varying steadily through the gradient from 2.0 GPa at the SUS316L surface to 14.4 GPa at the Al2O3 surface.
Similar content being viewed by others
References
Shen M, Bever MB (1972) J Mater Sci 7:741. doi:https://doi.org/10.1007/BF00549902
Bever MB, Duwez PE (1972) Mater Sci Eng 10:1
Kawasaki A, Watanabe R (1987) J Jpn Inst Met 51:525
Niino M (1990) J Jpn Soc Powder Powder Metall 37:241
Kieback B, Neubrand A, Riedel H (2003) Mater Sci Eng A632:81
Watanabe R, Nishida T, Hirai T (2003) Met Mater Int 9:513
Ilschner B (1993) J Phys IV 3:763
Cherradi N, Kawasaki A, Gasik M (1994) Compos Eng 4:883
Miyamoto Y, Kaysser WA, Rabin BH, Kawasaki A, Ford RG (1999) Functionally graded materials: design, processing and applications. Kluwer Academic Publishers, Boston
Niino M, Kisara K (2004) J Jpn Soc Powder Powder Metall 51:242
Grujicic M, Zhao H (1998) Mater Sci Eng A252:117
Matsuno S, Inomoto H, Ameyama K (2000) In: Proceedings of powder metallurgy world congress exhibition 2000, p 745
Shinagawa K (2000) Computer aided design of graded powder compacts to control sintering defects, Functionally Graded Materials in the 21st Century. A Workshop on Trends and Forecasts, Tsukuba, Japan
Pietrzak K, Kaliński D, Chmielewski M (2007) J Eur Ceram Soc 27:1281
Liu H, Tao J, Gautreau Y, Zhang P, Xu J (2009) Mater Des 30:2785
Orrù R, Licheri R, Locci AM, Cincotti A, Cao G (2009) Mater Sci Eng R 63:127
Tokita M (1997) In: Proceeding of the international symposium on microwave, plasma and thermomechanical processing of advanced materials, Osaka University, Japan, p 69
Hong-wei N, Hang H, Guang-qiang L, Jing L (2008) J Iron Steel Res Int 15:73
Xu Z, Jia C, Kuang C, Chu K, Qu X (2009) J Alloys Compd 484:924
Kim B, Hiraga K, Morita K, Yoshida H (2007) Scr Mater 57:607
Gao L, Hong JS, Miyamoto H, Torre SDDL (2000) J Eur Ceram Soc 20:2149
Tokita M, Kawahara M, Mizuuchi K, Makino Y (2009) J Jpn Soc Powder Powder Metall 56:383
Hong C, Zhang X, Li W, Han J, Meng S (2008) Mater Sci Eng A498:437
Zhang X, Li W, Hong C, Han W, Han J (2008) Scr Mater 59:1214
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Radwan, M., Nygren, M., Flodström, K. et al. Fabrication of crack-free SUS316L/Al2O3 functionally graded materials by spark plasma sintering. J Mater Sci 46, 5807–5814 (2011). https://doi.org/10.1007/s10853-011-5536-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10853-011-5536-2