Abstract
The design, in which the capsules are packed in the bed at different sections based on the Phase Change Material (PCM) melting temperature, is an effective method to improve the heat-storage performance of the latent heat energy storage system. A latent heat storage system was established in the present study in order to optimize the arrangement of cascaded PCM capsules. Four kinds of paraffin with different melting temperatures were selected as the PCM for the experiment. The effects of stage number, cascade ratio and melting temperature on the heat-storage performance of the latent heat storage system were investigated during the charging and discharging operations. The complete time of charge and discharge, heat storage-release capacity, energy efficiency, exergy efficiency and entransy dissipation (based on a new entransy theory) were computed for different arrangement cases, in order to analyze and evaluate the heat-storage performance of the system under different stage numbers and cascade ratios of PCMs. The results revealed that the arrangement of cascaded PCM capsules has an obvious effect on the heat-storage performance of the system. When more high melting PCMs are adopted, the heat storage-release capacity, energy efficiency and exergy efficiency increases, while the entransy dissipation decreases. However, the temperature increase becomes slow, and the charging or discharging process becomes long.
Similar content being viewed by others
Abbreviations
- c:
-
Specific heat (J·kg−1·K−1)
- Ex:
-
Exergy (kJ)
- Exsup :
-
Exergy transfer rate (kJ)
- Exs :
-
Exergy stored during heat storage
- Exsup :
-
Exergy transfer rate from HTF to PCMs (kJ)
- P:
-
Heat transfer rate (kJ·s−1)
- Q:
-
Thermal energy (kJ)
- T:
-
Temperature (K)
- t:
-
Time (s)
- T0 :
-
Reference temperature (K)
- ΔG:
-
Entransy increment (kJ)
- η :
-
Efficiency
- ϕ G :
-
Entransy dissipation
- f:
-
Fluid
- pcm:
-
Phase change material
- l:
-
Liquid phase
- s:
-
Solid phase
- in:
-
Inlet
- out:
-
Outlet
- ini:
-
Initial
- ex:
-
Exergy
- f:
-
Fluid
- ex:
-
Exergy
- in:
-
Inlet
- ini:
-
Initial
- l:
-
Liquid phase region
- out:
-
Outlet
- p:
-
Two-phase region
- pcm:
-
Phase changed material
- s:
-
Solid phase region
References
Z.H. Ge, F.Y. Zhang, Y.J. Zhang, Simulation on performance improvement of single thermocline energy storage tank. Proc. CSEE 39, 773–781 (2019)
H. Guo, Y.J. Xu, X.J. Zhang et al., Off-design performance of compressed air energy storage system with thermal storage. Proc. CSEE 39, 1366–1376 (2019)
M.M. Farid, A. Kanzawa, Thermal performance of a heat storage module using PCMs with different melting temperatures: mathematical modeling. J. Sol. Energy Eng. 111, 152–157 (1989)
R.V. Seeniraj, N.L. Narasimhan, Performance enhancement of a solar dynamic LHTS module having both fins and multiple PCMs. Sol. Energy 82, 535–542 (2008)
G. Alva, L. Liu, X. Huang et al., Thermal energy storage materials and systems for solar energy applications. Renew. Sustain. Energy Rev. 68, 693–706 (2017)
T. Watanabe, A. Kanzawa, Second law optimization of a latent heat storage system with PCMs having different melting points. Heat Recovery Syst. CHP 15, 641–653 (1995)
R. Domanski, G. Fellah, Exergy analysis for the evaluation of a thermal storage system employing PCMS with different melting temperatures. Appl. Therm. Eng. 16, 907–919 (1996)
Z.X. Gong, A.S. Mujumdar, Thermodynamic optimization of the thermal process in energy storage using multiple phase change materials. Therm. Eng. 17, 1067–1083 (1997)
Q. Mao, H. Chen, Y. Yang, Energy storage performance of a PCM in the solar storage tank. J. Therm. Sci. 28, 195–203 (2019)
X. Hou, Y. Xin, C. Yang et al., Three-dimensional heat transfer analysis for a thermal energy storage canister. J. Therm. Sci. 10, 52–57 (2001)
S. Shaikh, K. Lafdi, Effect of multiple phase change materials (PCMs) slab configurations on thermal energy storage. Energy Convers. Manag. 47, 2103–2117 (2006)
M. Fang, G. Chen, Effects of different multiple PCMs on the performance of a latent thermal energy storage system. Appl. Therm. Eng. 27, 994–1000 (2007)
J.N.W. Chiu, V. Martin, Multistage latent heat cold thermal energy storage design analysis. Appl. Energy 112, 1438–1445 (2013)
H.J. Xu, C.Y. Zhao, Thermodynamic analysis and optimization of cascaded latent heat storage system for energy efficient utilization. Energy 90, 1662–1673 (2015)
Y.B. Tao, Y.L. He, Y.K. Liu, W.Q. Tao, Performance optimization of two-stage latent heat storage unit based on entransy theory. Heat Mass Transf. 77, 695–703 (2014)
H.J. Xu, C.Y. Zhao, Thermal performance of cascaded thermal storage with phase-change materials (PCMs). Part I: steady cases. Heat Mass Transf. 106, 932–944 (2017)
H.J. Xu, C.Y. Zhao, Thermal performance of cascaded thermal storage with phase-change materials (PCMs). Part II: unsteady cases. Heat Mass Transf. 106, 945–957 (2017)
Y.K. Liu, Y.B. Tao, Thermodynamic analysis and optimization of multistage latent heat storage unit under unsteady inlet temperature based on entransy theory. Appl. Energy 227, 488–496 (2018)
Z.Y. Guo, H.Y. Zhu, X.G. Liang, Entransy—A physical quantity describing heat transfer ability. Heat Mass Transf. 50, 2545–2556 (2007)
X.T. Cheng, X.G. Liang, Entransy loss in thermodynamic processes and its application. Energy 44(1), 964–972 (2012)
X.T. Cheng, W.H. Wang, X.G. Liang, Optimization of heat transfer and heat-work conversionbased on generalized heat transfer law. Sci. China Technol. Sci. 55, 2847–2855 (2012)
X.T. Cheng, W.H. Wang, X.G. Liang, Entransy analysis of open thermodynamic systems. Chin. Sci. Bull. 57, 2934–2940 (2012)
J. Guo, X. Huai, The heat transfer mechanism study of three-tank latent heat storage system based on entransy theory. Heat Mass Transf. 97, 191–200 (2016)
G. Manfrida, R. Secchia, K. Stanczyk, Modelling and simulation of phase change material latent heat storages applied to a solar-powered organic rankine cycle. Energy 179, 378–388 (2016)
K.E. Elfeky, N. Ahmed, Q.W. Wang, Numerical comparison between single PCM and multi-stage PCM based high temperature thermal energy storage for CSP tower plants. Appl. Therm. Eng. 139, 609–622 (2018)
X.W. Cheng, X.Q. Zhai, Thermal performance analysis and optimization of a cascaded packed bed cool thermal energy storage unit using multiple phase change materials. Appl. Energy 215, 566–576 (2018)
B. Li, X.Q. Zhai, X.W. Cheng, Thermal performance analysis and optimization of multiple stage latent heat storage unit based on entransy theory. Heat Mass Transf. 135, 149–157 (2019)
H. Michels, R. Pitz-Paal, Cascaded latent heat storage for parabolic trough solar power plants. Sol. Energy 81, 829–837 (2007)
M. Ezra, Y. Kozak, V. Dubovsky, G. Ziskind, Analysis and optimization of melting temperature span for a multiple-PCM latent heat thermal energy storage unit. Appl. Therm. Eng. 93, 315–329 (2016)
L. Yang, X.S. Zhang, Charge performance of packed bed thermal storage unit with phase change material having different melting points. CIESC J. 63, 1032–1037 (2012)
Y. Zhao, Y. You, H.B. Liu, Experimental study on the thermodynamic performance of cascaded latent heat storage in the heat charging process. Energy 157, 690–706 (2018)
I. Dincer, M.A. Rosen, Thermal Energy Storage: Systems and Applications, 2nd edn. (Wiley, West Sussex, 2010).
A. Lake, B. Rezaie, Energy and exergy efficiencies assessment for a stratified cold thermal energy storage. Appl. Energy 220, 605–615 (1995)
Acknowledgement
This work was supported by the National Key R&D Program of China (No. 2017YFB0902100).
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Zhang, Z., Ci, Z. & Zhang, T. Heat-Storage Performance Optimization for Packed Bed Using Cascaded PCMs Capsules. Int J Thermophys 42, 72 (2021). https://doi.org/10.1007/s10765-021-02828-7
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s10765-021-02828-7