Abstract
This paper presents a dual-band 28/38 GHz two elements multiple-input multiple-output (MIMO) antenna with high isolation for 5G applications. The suggested antenna is a monopole with rectangular and triangle stubs added to the patch and a partial ground plane to achieve the dual band’s behavior. Two elements of the suggested antenna are combined and placed orthogonally to achieve the high isolation features of the MIMO configuration at 28/38 GHz. The MIMO configuration has a size of 27.65 \(\times\) 12 \(\times\) 0.273 mm3. The suggested MIMO prototype is fabricated and tested. The tested results achieved dual frequency bands with S11 lower than − 10 dB within two frequency bands (26–30 GHz and 36–41.5 GHz) and S21 lower than − 20 dB through the two operated bands. The suggested antenna has semi-omnidirectional radiation patterns in both planes. As well, its measured peak gain is 5.2 dBi and 5.3 dBi at the two operated frequency bands, respectively. Also, the MIMO parameters are extracted to validate the simulated results. The simulated and tested results have a good matching within the two operating bands which suggests the proposed structure be utilized in 5G communications.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
The rapid development of the fifth generation (5G) enhances the performance of the wireless communication systems such as increasing data rate, connectivity, and spectral efficiency and reducing the latency of these systems [1,2,3]. The data rate of the 5G systems is 10 times more than the 4G systems and has high connectivity between devices which achieves the Internet of Things (IoT) technology with high reliability [4]. The FCC assigned frequency bands from 25 GHz up to 70 GHz to be utilized for the 5G applications [2, 5]. These bands suffer from attenuation because of the path loss and atmospheric absorption which makes the antenna researchers design antenna with high gain and wideband features to tackle these problems [6,7,8,9,10]. Also, an increasing number of antenna elements (MIMO technology) enhances the transmission quality and increases the capacity of the system and reduces the multipath problems [11,12,13]. So, by introducing a MIMO system with high isolation between antenna elements, the overall performance of the system as high data rate, high capacity, lower multipath effect, and reliability can be improved [14,15,16]. Recently, a dual-band 28/38 GHz MIMO antenna is developed by researchers [7, 12, 17,18,19,20,21,22,23,24,25,26,27]. In [7], dual bands 27/39 GHz MIMO antenna with two elements, isolation higher than 25 dB, and peak gain around 5 dBi is introduced. A dual-band circular polarized 4 ports antenna operated at 28/38 GHz with isolation around 36 dB and peak gain higher than 7 dBi is discussed in [12]. In [17], a dual-band 28/38 GHz two elements MIMO antenna with 30 dB isolation and simulated peak gain of 7 dBi is achieved. A dual-band 28/38 circular polarized two ports MIMO antenna using an artificial neural network (ANN) is proposed in [18]. In [19], dual bands 28/38 GHz MIMO antenna with two ports, isolation higher than 25 dB, and peak gain around 1.7 dBi is introduced. A four-port MIMO antenna operated at 28/37 GHz is investigated in [20]. A dual-band 28/38 GHz slot MIMO antenna with two elements and isolation higher than 20 dB is introduced [21]. In [22], four ports dual-band 28/38 GHz antenna with more than 20 dB isolation and peak gain more than 7 dBi is accomplished. A dual-band four ports antenna worked at 28/38 GHz with isolation around 25 dB and peak gain higher than 5 dBi is discussed in [23]. In [24], a dual-band 28/38 GHz four elements MIMO antenna with 30 dB isolation and simulated peak gain of 9 dBi is achieved. A dual-band 28/38 2-port MIMO SIW antenna with peak gain higher than 5 dBi is proposed in [25]. A dual-band 28/38 GHz four elements MIMO/array antenna with a simulated peak gain of 9 dBi is investigated in [26]. In [27], six ports dual-band 28/38 GHz loop antenna with more than 25 dB isolation and simulated peak gain of more than 4.5 dBi is accomplished.
In this paper, a dual-band 28/38 GHz two elements MIMO antenna with high isolation for 5G applications is suggested. The triangle and rectangular stubs are merged with the patch to achieve the proposed 5G frequency bands. The two elements of the suggested antenna with a size of 27.65 \(\times\) 12 \(\times\) 0.203 mm3 are combined and placed orthogonally to achieve the high isolation features of the MIMO configuration. The HFSS commercial software is used in the antenna design. This paper has arranged with the following sections: first, Section II, the design of the single element antenna to achieve the desired 28/38 GHz frequency bands is discussed. Second, in Section III, the MIMO antenna design procedures are presented. Third, in Section IV, the MIMO tested results (impedance and radiation characteristics), and its diversity parameters such as envelop correlation coefficient (ECC), the diversity gain (DG), and channel capacity loss (CCL) are extracted and presented. Finally, the conclusion of the paper is introduced to summarize the antenna performance and presented in Section V.
2 Design Procedures for Single Antenna
The development of the suggested antenna is illustrated in Fig. 1. The antenna is designed using Rogers RO4003 substrate with thickness and dielectric constant of 0.203 mm and 3.55, respectively. As the initial start, the conventional patch antenna with a rectangular patch of W1 = 5 mm and L1 = 4 mm (antenna 1) with the full ground plane of 12 mm length, and microstrip line with Wf = 0.4 mm and Lf = 7 mm as shown in Fig. 1a, is designed to operate at fundamental mode around 30.5 GHz as shown in Fig. 2 (green dotted line). Second, a partial ground plane (Lg) with a length of 6 mm is utilized instead of the full ground plane (antenna 2) to enhance the antenna bandwidth. By adding rectangular stub (L2) of 2.1 mm and triangular stub (W2) of 2.05 mm on the same side of the rectangular patch, a resonance response extended with S11 lower than − 10 dB from 25.9 and 30.4 GHz as illustrated in Fig. 2 (antenna 3). Finally, to achieve the second resonance, another two rectangular stubs (L3) of 1 mm are added to achieve a response from 36.4 to 40.2 GHz as shown in Fig. 2 (antenna 4). The HFSS simulator is used to achieve the results of the suggested antenna.
Based on the previous design procedures, antenna 4 is considered the suggested antenna to produce the proposed 28/38 GHz frequency bands. So, the suggested antenna layout as shown in Fig. 3a is fabricated, and its prototype photograph with a launcher connector is illustrated in Fig. 3b.
The simulated as well as the tested S11 results with a frequency of the suggested single element dual-band antenna are displayed in Fig. 4. The simulated results are tested using the vector network analyzer (VNA) (Rohde & Schwarz ZVA 67), and achieved frequency bands are from 26 to 30 GHz in the first band, while the second frequency band is from 36.5 up to 40 GHz. However, the tested results are achieved frequency ranges from 28 to 29 GHz for the first band and from 37.5 up to 39 GHz for the second band. There is a small discrepancy between the two results due to the fabrication and measurements tolerance which cannot be tackled.
3 The Suggested MIMO Antenna and Parametric Analysis
The design of the two elements MIMO antenna and the technique used to eliminate the mutual coupling to enhance the antenna operation are investigated in this section. There are two configurations which are studied as shown in Fig. 5. The first one is the side-by-side orientation as shown in Fig. 5a, and the other is the orthogonal orientation as shown in Fig. 5b. The separation (d) between the 2 elements is the same in the two configurations. The simulation results of the two configurations are shown in Fig. 6 to show the effect of the antenna orientation on the matching and the isolation between the antenna elements. As shown in Fig. 6, the reflection coefficient of the two configurations is almost the same, while the isolation between antenna elements is enhanced in the case of the orthogonal orientation than the side-by-side orientation, especially at the lower frequency bands. So, orthogonal orientation is suggested in the MIMO antenna design.
The effect of the separation (d) between antenna elements on the antenna performance is illustrated in Fig. 7. When the separation (d) is changed from 3.55 to 4.3 mm, the isolation between elements is enhanced. So, the optimized distance (d) equals 4.3 mm to achieve the desired performance. The simulated surface current distributions for the suggested MIMO antenna at f = 28 GHz and f = 38 GHz are shown in Fig. 8. The results are extracted when port 1 is radiated and port 2 is matched to 50 Ω and verse versa. It is seen that, first, the current is collected around the rectangular stub and triangular stub at 28 GHz which means the two stubs are responsible for radiation at this frequency band, while the current is collected around the other two stubs (on the right of the patch) at 38 GHz. Second, the current is collected around the operated port with a small amount of current passed to other ports which validate the high isolation between ports.
4 The Tested Results and Investigation
The suggested MIMO antenna is fabricated on the same previous substrate, and the total size of the antenna equals W = 27.65 mm, L = 12 mm, and d = 4.3 mm. The fabricated prototypes with and without connectors are shown in Fig. 9. The two elements are added in orthogonal orientation as discussed in the previous section. Figure 10 illustrates the simulated and tested results of the suggested antenna. The antenna operated (from simulated results) at a frequency band from 25.9 to 30.6 GHz and from 36.1 to 40.3 GHz with isolation lower than 30 dB and 22.2 dB for the first and second bands, respectively. However, the antenna operated (from tested results) at frequency band from 27.5 to 29.4 GHz and from 36.4 to 41.9 GHz with isolation lower than 34 dB and 22.2 dB for the first and second bands, respectively. The differences between the two results are because of the fabrication and measurements tolerance which cannot be overcome.
The simulated and tested radiation pattern results (E-plane and H-plane) at 28 GHz and 38 GHz when antenna is excited at port 1, and terminated with 50 Ω load at port 2, are shown in Fig. 11. The antenna has a semi-omnidirectional pattern at the two frequency bands, and there is a consistent trend between the simulated and tested results with small differences between them because of the measurements setup. The technique used to measure the antenna gain is discussed in [24, 26]. Figure 12 shows the simulated and tested peak gain results of the suggested antenna when it is also excited at port 1. The measured peak gain is 5.2 dBi and 5.3 dBi at the operated frequency bands, respectively. Furthermore, the measured gains mimic the simulated one with a small discrepancy due to the tolerance of the measurement setup.
The quality of the suggested MIMO antenna is measured by extracting the ECC, DG, and CCL parameters. One of the important parameters is the ECC because it evaluates the correlation between ports. The lower values reflect the higher performance of the MIMO system. By suggesting uniform multipath, the ECC can be extracted and calculated from S-parameters as [28].
Figure 13 shows the simulated and tested ECC results with a frequency of the suggested 2 ports dual-band MIMO antenna. The value of the ECC is lower than 0.0001 in the first band and lower than 0.0002 in the second band (lower than the acceptable level of 0.5 [29]) with the good matching between the simulated and measured results.
The ECC can be connected with DG through Eq. (2) to judge the MIMO performance [30].
Figure 14 illustrates the simulated and tested DG results with a frequency of the suggested 2 ports dual-band MIMO antenna. The value of the DG equals around 9.99 in both bands with a good tendency between the two results.
The data rate transmitted in the communication channel can be evaluated by CCL (Bit/S/Hz) [29]. The CCL can be calculated using Eqs. (3) and (4) [30]
Figure 15 shows the simulated and tested CCL results with a frequency of the suggested 2 ports dual-band MIMO antenna. The CCL equals a value lower than 0.4 bit/s/Hz within the operated frequency bands.
Finally, Table 1 shows the comparison between the suggested antennas with other designs to judge the antenna performance. From Table 1, it is obvious that the suggested antenna can be recommended for the dual bands 28/38 5G systems.
5 Conclusion
Two elements with dual bands MIMO antenna have been suggested for 5G communications. The suggested antenna has been designed to operate at frequency bands from 26 GHz up to 30 GHz, from 36 GHz up to 41.5 GHz, and S21 lower than − 20 dB through the two operated bands. MIMO parameters as ECC, DG, and CCL have been extracted from simulated and measured results to validate the antenna design and show the high quality of the suggested two elements MIMO antenna. The simulated and tested results have a good trend within the two operating bands which suggests the proposed structure to be utilized in 5G communications.
Data Availability
There are no supplementary materials, and the data is available upon reasonable request.
References
Alassawi, Sarah A., Wael AE Ali, and Mohamed RM Rizk. "Compact Circular Ring Antenna for 5G Mobile Communication Applications." Journal of Nano-and Electronic Physics 13, no. 3 ,2021.
FCC Takes Steps to Make Millimeter Wave Spectrum Available for 5G, Federal Communications Commission, 2019
Rappaport, T.S., Xing, Y., MacCartney, G.R., Molisch, A.F., Mellios, E. and Zhang, J., "Overview of millimeter wave communications for fifth-generation (5G) wireless networks with a focus on propagation models". IEEE Transactions on antennas and propagation, 65(12), pp.6213-6230, 2017.
Loghin, D., Cai, S., Chen, G., Dinh, T.T.A., Fan, F., Lin, Q., Ng, J., Ooi, B.C., Sun, X., Ta, Q.T. and Wang, W., "The disruptions of 5G on data-driven technologies and applications". IEEE transactions on knowledge and data engineering, vol.32, no.6, 1179-1198, 2020.
Al-Falahy, Naser, and Omar YK Alani. "Millimeter wave frequency band as a candidate spectrum for 5G network architecture: A survey." Physical Communication, 32, 120–144, 2019.
Shayea, Ibraheem, Tharek Abd Rahman, Marwan Hadri Azmi, and Md Rafiqul Islam. "Real measurement study for rain rate and rain attenuation conducted over 26 GHz microwave 5G link system in Malaysia." IEEE Access 6. 19044–19064, 2018.
Ali, Wael, Sudipta Das, Hicham Medkour, and Soufian Lakrit. "Planar dual-band 27/39 GHz millimeter-wave MIMO antenna for 5G applications." Microsystem Technologies 27, 1 283-292, 2020.
Zahra, Hijab, Wahaj Abbas Awan, Wael Abd Ellatif Ali, Niamat Hussain, Syed Muzahir Abbas, and Subhas Mukhopadhyay. "A 28 GHz Broadband Helical Inspired End-Fire Antenna and Its MIMO Configuration for 5G Pattern Diversity Applications." Electronics 10, 4 405, 2021.
Hussain, Niamat, Wahaj Abbas Awan, Wael Ali, Syeda Iffat Naqvi, Abir Zaidi, and Tuan Tu Le. "Compact wideband patch antenna and its MIMO configuration for 28 GHz applications." AEU-International Journal of Electronics and Communications 132, 153612, 2021.
Ibrahim, Ahmed A., and Wael AE Ali. "High gain, wideband and low mutual coupling AMC-based millimeter wave MIMO antenna for 5G NR networks." AEU-International Journal of Electronics and Communications 142 153990, 2021.
Jilani, Syeda Fizzah, and Akram Alomainy. "Millimetre-wave T-shaped MIMO antenna with defected ground structures for 5G cellular networks." IET Microwaves, Antennas & Propagation 12, no. 5, pp. 672–677, 2018.
Alnemr, Fadwa, Mai Foua’ad Ahmed, and Abdulhamed Abdulmonem Shaalan. "A Compact 28/38 GHz MIMO Circularly Polarized Antenna for 5G Applications." Journal of Infrared, Millimeter, and Terahertz Waves 42, no. 3 (2021): 338–355.
Hala M M, Mohamed I A and Abdelhamed A S 2019 A Novel Dual-band 28/38 GHz Slotted Microstrip MIMO Antenna for 5G Mobile Applications Journal of Electromagnetic Waves and Applications 33 1581–1590
Yang, Binqi, Zhiqiang Yu, JiLan, Ruoqiao Zhang, Jianyi Zhou, and Wei Hong. "Digital beamforming-based massive MIMO transceiver for 5G millimeter-wave communications." IEEE Transactions on Microwave Theory and Techniques 66, no. 7, pp. 3403–3418, 2018.
Jo, Ohyun, Jung-Ju Kim, Jungmin Yoon, Dooseok Choi, and Wonbin Hong. "Exploitation of dual-polarization diversity for 5G millimeter-wave MIMO beamforming systems." IEEE Transactions on Antennas and Propagation 65, no. 12, pp. 6646-6655, 2017.
Mneesy, Tarek S., Radwa K. Hamad, Amira I. Zaki, and Wael A.E. Ali. "A Novel High Gain Monopole Antenna Array for 60 GHz Millimeter-Wave Communications." Applied Sciences 10, no. 13, pp. 4546, 2020.
Marzouk, Hala M., Mohamed Ismail Ahmed, and Abdel Hamied Abdel Meneam S. "Novel dual-band 28/38 GHz MIMO antennas for 5G mobile applications." Progress in Electromagnetics Research 93, pp.103–117, 2019.
Aliakbari, Hanieh, AbdolaliAbdipour, Alessandra Costanzo, Diego Masotti, Rashid Mirzavand, and PedramMousavi. "ANN-based design of a versatile millimetre-wave slotted patch multi-antenna configuration for 5G scenarios." IET Microwaves, Antennas & Propagation, Vol. 11, no. 9, PP. 1288–1295, 2017.
Hasan, M.N., Bashir, S. and Chu, S., Dual band omnidirectional millimeter wave antenna for 5G communications. Journal of Electromagnetic Waves and Applications, 33(12), pp.1581-1590, 2019.
Ikram, Muhammad, Yifan Wang, Mohammad S. Sharawi, and Amin Abbosh. "Dual band circular MIMO antenna system for 5G wireless devices. "In 2018 IEEE International Symposium on Antennas and Propagation & USNC/URSI National Radio Science Meeting, pp. 247–248.IEEE, 2018.
Omar, Amjad, Mousa Hussein, Indu J. Rajmohan, and Khaled Bathich. "Dual-band MIMO coplanar waveguide-fed-slot antenna for 5G communications." Heliyon , vol. 7, no. 4, p. e06779, 2021.
Aghoutane, Bilal, Sudipta Das, Mohammed EL Ghzaoui, B. T. P. Madhav, and Hanan El Faylali. "A Novel Dual Band High Gain 4-port Millimeter Wave MIMO Antenna Array for 28/37 GHz 5G Applications." AEU-International Journal of Electronics and Communications , vol. 145, no. 4, p. 154071, 2022.
Rafique, Umair, Shobit Agarwal, Nasir Nauman, Hisham Khalil, and Khalil Ullah. "Inset-fed Planar Antenna Array for Dual-band 5G MIMO Applications." Progress In Electromagnetics Research C, vol.112, ,pp. 83-98, 2021.
Farahat, Asmaa Elsayed, and Khalid Fawzy Ahmed Hussein. "28/38 GHz dual-band Yagi-Uda antenna with corrugated radiator and enhanced reflectors for 5G MIMO antenna systems." Progress In Electromagnetics Research C, vol.101,pp. 159–172, 2020.
Liu, Pengfei, Xiao-Wei Zhu, Yan Zhang, Xiang Wang, Chunfeng Yang, and Zhi Hao Jiang. "Patch antenna loaded with paired shorting pins and H-Shaped slot for 28/38 GHz dual-band MIMO applications." IEEE Access, vol. 8 , pp. 23705–23712, 2020.
Farahat, Asmaa E., and Khlaid FA Hussein. "Dual-band (28/38 GHz) MIMO antenna system for 5G mobile communications with efficient DoA estimation algorithm in noisy channels." The Applied Computational Electromagnetics Society Journal (ACES) , Vol. 36, No. 3, pp.282–294, 2021.
H. M. Marzouk, M. I. Ahmed, and A. A. Shaalan, “A Novel Dual-Band 28/38 GHz AFSL MIMO Antenna for 5G Smartphone Applications,” J. Phys. Conf. Ser., vol. 1447, no. 1, 2020
Ibrahim, Ahmed A., and Wael AE Ali. "High isolation 4-element ACS-fed MIMO antenna with band notched feature for UWB communications." International Journal of Microwave and Wireless Technologies, pp.1–11, 2021.
Aboelleil, Heba, Ahmed A. Ibrahim, and Ashraf AM Khalaf. "A compact multiple-input multiple-output antenna with high isolation for wireless applications." Analog Integrated Circuits and Signal Processing, vol. 108, pp. 17–24, 2021.
Ibrahim, Ahmed A., Jan Machac, and Raed M. Shubair. "Compact UWB MIMO antenna with pattern diversity and band rejection characteristics." Microwave and Optical Technology Letters, 59 6 1460-1464, 2017.
Funding
Open access funding provided by The Science, Technology & Innovation Funding Authority (STDF) in cooperation with The Egyptian Knowledge Bank (EKB).
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of Interest
The authors declare no competing interests.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Sabek, A.R., Ali, W.A.E. & Ibrahim, A.A. Minimally Coupled Two-Element MIMO Antenna with Dual Band (28/38 GHz) for 5G Wireless Communications. J Infrared Milli Terahz Waves 43, 335–348 (2022). https://doi.org/10.1007/s10762-022-00857-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10762-022-00857-3