Abstract
Clostridioides difficile infections are a significant threat to our healthcare system, and rapid and accurate diagnostics are crucial to implement the necessary infection prevention and control measurements. Nucleic acid amplification tests are such reliable diagnostic tools for the detection of toxigenic Clostridioides difficile strains directly from stool specimens. In this multicenter evaluation, we determined the performance of the revogene C. difficile assay. The analysis was conducted on prospective stool specimens collected from six different sites in Europe. The performance of the revogene C. difficile assay was compared to the different routine diagnostic methods and, for a subset of the specimens, against toxigenic culture. In total, 2621 valid stool specimens were tested, and the revogene C. difficile assay displayed a sensitivity/specificity of 97.1% [93.3–99.0] and 98.9% [98.5–99.3] for identification of Clostridioides difficile infection. Discrepancy analysis using additional methods improved this performance to 98.8% [95.8–99.9] and 99.6% [99.2–99.8], respectively. In comparison to toxigenic culture, the revogene C. difficile assay displayed a sensitivity/specificity of 93.0% [86.1–97.1] and 99.5% [98.7–99.9], respectively. These results indicate that the revogene C. difficile assay is a robust and reliable aid in the diagnosis of Clostridioides difficile infections.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
Clostridioides difficile infections (CDI), caused by the Gram-positive, spore-forming anaerobic bacterium Clostridioides difficile (C. difficile), create a tremendous burden on our healthcare system. In Europe alone, approximately 124.000–172.000 CDI cases are identified on a yearly basis, and CDI Management attributed costs approach €3.000 million [1,2,3,4]. Furthermore, CDI remains underdiagnosed with approximately 39,000 missed cases yearly, as reported by the EUCLID study, due to unawareness of the condition, unawareness of when to request a CDI test and nonoptimal testing strategies [5, 6]. Therefore, the true CDI burden on the healthcare system remains unknown. However, together with the emergence of hypervirulent C. difficile strains (e.g., 027/NAP1 strain), this CDI problematic has fueled the development of (i) new technologies for diagnosing CDI, (ii) new therapeutic strategies, and (iii) optimized protocols for CDI infection prevention and control, to reduce the CDI-associated healthcare burden [7, 8].
To better understand the complex CDI problem, the European Society of Clinical Microbiology and Infectious Diseases (ESCMID) established a workgroup of international experts to define uniform European guidelines. Importantly, these guidelines provide detailed diagnostic guidance for routine detection of C. difficile [9]. Recently, the guidelines were updated to incorporate more novel technological developments, specifically to cover the expansion in available nucleic acid amplification techniques (NAAT) [10]. Overall, it was concluded that a two-step algorithm, consisting of a highly sensitive screening test followed by a more specific confirmatory test detecting free toxins, is required because stand-alone methods failed to reach adequate positive predictor values [10]. In addition, the inability to differentiate CDI patients from C. difficile carriers when testing for the presence of a toxigenic strain rather than free toxins further limited the use of certain stand-alone techniques. Further, defining optimal diagnostic pathways requires the incorporation of both the performance and the effectiveness of testing (i.e., time to result, workflow, etc.). However, it remains difficult to quantify these aspects, and often there is a lack of sufficient literature data. Nonetheless, toxigenic culture and cell culture cytotoxicity neutralization assay (CCNA) were identified as not suitable for routine application due to their complexity and long turnaround time [11].
In parallel with the emergence of European CDI guidelines, the healthcare system has been steadily restructuring. The upcoming trend (as described by the WHO) of both centralization and decentralization arose from continuous pressure on the healthcare system due to aging of the population and the economic restraints on the health sector. This restructuring has since fueled the emergence of larger centralized laboratories, serving multiple hospitals simultaneously, to improve the efficiency of laboratory testing. However, a centralized lab environment has the disadvantage that it creates a delay in result reporting due to the requirement of specimen transport. This opens the door for the implementation of more advanced technologies. With respect to CDI, the delay to result imposed by transport of the specimen to the laboratory followed by a multistep diagnostic approach in the laboratory might be detrimental to CDI outcome [12]. This does not only impact infection prevention and control measurements but proper patient management in general. Recent reports regarding the increase in CDI incidence hint toward an unresolved issue and the need for further improvement in the efficiency of CDI diagnostics and infection prevention and control measurements [13,14,15].
In contrast to the centralization of lab infrastructure, a separate and opposite field of point-of-care testing (POCT) has emerged simultaneously. One of the purposes of POCT platforms is to decentralize certain parts of central laboratory testing to reduce time to result and improve clinical decision making. Here, we report the results of a multicenter study in Europe for identification of toxigenic C. difficile strains using a new molecular platform called revogene™ from GenePOC Inc. (Quebec, Canada), recently acquired by Meridian Biosciences, that might suit as POCT platform with the right test menu in the future.
Methods
Study design
From January to December 2017, the manufacturer coordinated the data collection and analysis of different local microbiology laboratories and national and/or regional reference laboratories for Clostridioides difficile across Europe. In total, six laboratories (representatives of the following countries: (i) France, (ii) the Netherlands, (iii) Belgium, (iv) the UK, (v) Switzerland, and (vi) Italy) participated in this study with the purpose of evaluating the revogene™ C. difficile assay (abbreviated to “revogene” in the data analysis) in comparison to their routine diagnostic methods. The different laboratories were unaware of the participation of the other laboratories for the duration of their study. The participating laboratories were carefully chosen to obtain sufficient data from various CDI approaches used in Europe for detection of toxigenic C. difficile and CDI. The difference in the workflows used as reference was necessary for a well-rounded evaluation of the system, considering the gold standard ESCMID defined for CDI identification is different from the algorithm it recommends for actual CDI diagnosis, as it is too slow [9, 10]. This particular site selection therefore allowed a performance evaluation in terms of accuracy of identification both in the absolute and within a time-sensitive frame.
All evaluation sites collected unformed stool specimens, in a prospective manner, from their routine for the duration of their respective study. Routine testing was mostly performed in parallel to the revogene assay to avoid any bias as consequence of prolonged specimen storage. Collection, transport, and handling of the stool specimens occurred according to the local guidelines while in accordance with the specifications of the different manufacturers. For all the evaluation sites, the manufacturer provided the necessary equipment to work with the revogene C. difficile assay.
Of note, in Switzerland, two distinct sites participated in the study design: (i) Bioanalytica (oversaw data management) and (ii) Lucerne Cantonal Hospital (all specimens were transported to Bioanalytica for testing with the revogene, which was performed within 5 days of original specimen collection). Furthermore, Bioanalytica collected stool specimens from two subpopulations of patients: (i) patients suspected of CDI and (ii) outpatients not suspected of CDI. For the latter population, stool specimens from outpatients with a negative BD MAX™ Enteric Bacterial panel (BD) were selected for testing. The epidemiological findings of this investigation fall outside the scope of this publication. However, all specimens were tested with the proper methodology to be included in the performance calculations.
Definitions
As none of the microbiology laboratories used exactly the same methodology, either due to the fact that they used different CDI diagnostics algorithms or diagnostic tests from different manufacturers, general definitions were put in place to standardize the data analysis. Two main definitions were adopted: (i) CDI cases and (ii) C. difficile carriers (or “carriers” in short). A CDI case was defined when free toxin was detected directly from stool specimens. A C. difficile carrier was defined by the presence of a toxigenic strain in stools without any detectable free toxin.
For two sites (France and the Netherlands), the gold standards used to define CDI cases and C. difficile carriers were, respectively, CCNA and toxigenic culture, in accord with ESCMID guidelines [9, 10]. As for the remaining four sites (the UK, Belgium, Switzerland, and Italy), all used as gold standard different variations of the diagnostic algorithm currently recommended as a suitable, faster alternative to CCNA and toxigenic culture [10]. In general, stool samples found positive for toxin A/B to enzyme immunoassay (EIA) were considered CDI cases. On the other hand, C. difficile carriers were defined for EIA-negative specimens in which either the presence of toxin genes could be demonstrated through NAAT testing or toxigenic culture–proved positive.
A detailed overview of the different testing algorithms and commercial tests used at the different sites is provided in Table 1.
Discrepancy analysis
In case of discrepant results between the revogene and the routine methodology (and/or golden standard method), additional testing was performed. Table 1 provides an overview of the methodology used to resolve the discrepancies at each site (when available).
Data analysis and statistics
Sensitivity, specificities, and positive and negative predictive values are expressed as percentages. Confidence intervals were determined with Clopper-Pearson method.
Results
Inclusion rate and valid results
A total of 2662 unformed stool specimens were prospectively collected and tested with their routine CDI diagnostic algorithm, in parallel with the revogene, across six different evaluation sites in Europe. A total of 41 specimens (1.5%) were excluded from further analysis of which 21 (0.79%) due to invalid revogene results, 2 (0.08%) due to testing of external controls, 7 (0.26%) due to not in agreement with the manufacturer’s specifications, and 11 (0.41%) due to lack of sufficient reference data. For the 2621 specimens that were included in the analysis, 4.2% displayed an unresolved/indeterminate result with the revogene assay on initial testing, but after repetition, all specimens gave a valid result.
Site by site results
Table 2 provides a detailed overview of the performance characteristics for each site that participated in the multicenter study for identification of (i) CDI and (ii) tcdB+ strains, which is the sum of the number of CDI cases and the number of C. difficile carriers. Sensitivity/specificity of the revogene C. difficile assay for identification of CDI fluctuated between 85–100% and 97–100%, respectively. For the identification of tcdB+ strains, sensitivity/specificity fluctuated between 84–100% and 96–100%, respectively.
Revogene C. difficile overall performance
Identification of CDI and tcdB+ strains
According to the definitions described in the Methods section, Fig. 1 provides an overview of pooled performance of the revogene assay (as stand-alone method) for identification of CDI cases and tcdB+ strains. Overall, the revogene assay performed well with a sensitivity/specificity of 97.1% [93.3–99.0] and 98.9% [98.4–99.2] for identifying CDI cases and 91.9% [88.2–94.8] and 98.7% [98.2–99.1] for identifying tcdB+ strains. After resolving discrepancies with additional testing, the sensitivity/specificity improved to 98.8% [95.8–99.9] and 99.6% [99.2–99.8] for identifying CDI cases and to 95.7% [92.8–97.7] and 99.4% [99.0–99.8] for identification of tcdB+ stains.
Comparison to toxigenic culture
Three of the six evaluation sites performed toxigenic culture on all specimens tested which allowed us to compare the revogene assay against this gold standard method (Fig. 2). Overall, the revogene assay performed well with sensitivity/specificity of 90.4% [82.6–95.5] and 98.5% [97.4–99.2], respectively. This performance corresponded to a positive and negative predictive value (PPV/NPV) of 87.6% [80.1–92.3] and 98.9% [97.9–99.4], respectively, with a reported overall prevalence of 10.6% [8.7–12.9]. After resolving the discrepancies, the sensitivity, specificity, PPV, and NPV improved to 93.0 [86.1–97.1], 99.5 [98.7–99.9], 95.9 [89.7–98.4], and 99.1% [98.2–99.6], respectively.
Revogene assay as part of a multistep algorithm
In the above analysis, the revogene performance is determined as stand-alone method against the reference method. However, the European Society of Clinical Microbiology and Infectious Diseases (ESCMID) does not recommend the use of a single commercial test as stand-alone test for diagnosing CDI [9]. Therefore, we extended our data analysis to incorporate the revogene assay as part of a multistep (i.e., two- or optional three-steps) algorithm, with the revogene assay either at the (i) front of the algorithm, to be tested on all specimens (i.e., revogene -TOX), or (ii) at the end of the algorithm, as confirmatory test (GDH-TOX-revogene).
Overall, the revogene-TOX algorithm performed well with a sensitivity/specificity of 96.8% [92.1–99.1] and 100% [99.8–100] for identifying CDI cases and 92.2% [88.0–95.3] and 98.6% [98.0–99.1] for identifying tcdB+ strains (Fig. 3). Resolution of the discrepancies improved the sensitivity/specificity performance to 97.6% [93.2–99.5] and 100% for identifying CDI cases and 95.8% [92.4–98.0] and 99.3% [98.8–99.7] for identifying tcdB+ strains. On the other hand, the GDH-TOX-revogene algorithm performed similarly with a sensitivity/specificity of 100% [97.1–100] and 100% [99.8–100] for identifying CDI cases and 89.6% [85.1–93.2] and 99.8% [99.4–99.9] for identifying tcdB+ strains (Fig. 4). Resolution of the discrepancies improved the sensitivity/specificity performance to 92.0% [87.8–95.1] and 99.9% [99.7–100] for identifying tcdB+ strains.
Discussion
Despite significant effort and various strategies to improve CDI diagnostics, C. difficile remains a global healthcare burden that keeps challenging all stakeholders, from nurse to clinical microbiologist, to improve in their current field to overcome this global threat. At the beginning of the century, molecular biology techniques opened the door to improved diagnostics, but despite the enormous progression made in that field, molecular diagnostic techniques (like NAAT) remain underutilized when it comes to diagnosing CDI. Recently, the amount of available molecular NAAT assays for detection of CDI have vastly expanded which made the technology more accessible, especially in the central laboratory, and competitive in terms of pricing. However, with the emergence of POCT testing, NAAT technology for infectious diseases is now also more accessible to smaller labs, or it could be used to equip satellite labs connected to a central lab for urgent testing. In this work, we report the results from a multicenter Clostridioides difficile study that assessed the performance of a novel molecular platform (i.e., revogene™) from Meridian Biosciences Canada Inc. (Quebec, Canada). The revogene assay targets the tcdB gene of toxigenic C. difficile and required minimal hands-on time, and results were available in approximately an hour. The 1 to 8 flexible throughput combined with the ease of use would allow this platform to be implemented in both small satellite and central labs.
In this multicenter study, the revogene assay was capable of adequately identifying CDI cases and tcdB+ strains. However, current diagnostic guidelines in Europe recommend to perform a two-step algorithm for the identification of CDI cases [10]. In contrast, the recently updated clinical practice guidelines for CDI (by the IDSA and SHEA societies) state that it would be acceptable to use a stand-alone NAAT assay for diagnosis CDI under the condition that pre-defined criteria for stool specimen submission are used by clinicians and laboratory personnel [16]. Interestingly, here, we only observed minor differences between the revogene assay (stand-alone) and revogene-TOX algorithm in terms of correctly identifying CDI cases and tcdB+ strains. Due to the fact that in both scenarios (i.e., revogene and revogene-TOX) the same dataset was analyzed with the same definition for CDI cases and tcdB+ carriers, this might raise doubt on the usefulness of the confirmatory TOX test in such a two-step algorithm. However, it must be noted that the absence of the TOX test would not allow differentiation of CDI from asymptomatic carriage of C. difficile. When comparing the revogene-TOX and GDH-TOX-revogene algorithm, we also only observed some minor differences in performance which raises the general question about how to best define the balance between algorithm performance and time to result. However, this topic falls out of the scope of the current work, and additional research is required to answer this question.
A major strength of this work was the multicenter approach that allowed us to (i) capture data on the different C. difficile diagnostic methodologies used across Europe and (ii) gather an extensive dataset to determine the performance characteristics of the revogene assay. The work was further strengthened due to standardization of the dataset through the use of definitions for CDI and tcdB+ strains. This allowed us to compare different diagnostic algorithms for CDI under the same conditions. However, the fact that different CDI diagnostic methodologies were used and standardization of the data was required also imposes a limitation to the study as the results cannot be extrapolated and properly compared to the current available literature.
An added value of this system is a decrease in the turnaround time (TAT): This was extremely significant in the Belgian and French sites (23–47-h reduction), which are reference centers where culturing is conducted for epidemiological reasons; nonetheless, sites which already used workflows considered time-accurate for CDI diagnosis showed a decrease in TAT, if less marked (1 h for the Netherlands and Switzerland, 2 h for Italy and UK).
In conclusion, the revogene C. difficile molecular assay for detection of the tcdB gene of toxigenic Clostridioides difficile is a high quality and simple to use diagnostic test providing reliable results in approximately an hour. This makes the revogene assay suitable for implementation as diagnostic utility, either as frontline/confirmatory test in a multistep algorithm or as stand-alone method if used with proper institutional criteria for collection of CDI-suspected stool specimens.
References
Zarb P, Coignard B, Griskeviciene J, Muller A, Vankerckhoven V, Weist K et al (2012) The European Centre for Disease Prevention and Control (ECDC) pilot point prevalence survey of healthcare-associated infections and antimicrobial use. Euro Surveill 17(46)
Kuijper EJ, Coignard B, Tüll P, ESCMID Study group for Clostridium difficile; EU Member States; European Centre for Disease Prevention and Control (2006) Emergence of Clostridium difficile-associated disease in North America and Europe. Clin Microbiol Infect 12:2–18
Bouza E (2012) Consequences of Clostridium difficile infection: understanding the healthcare burden. Clin Microbiol Infect 18:5–12
HOPE (2013) Clostridium difficile infection in Europe, a CDI Europe report. Available from: http://www.multivu.com/assets/60637/documents/60637-CDI-HCP-Report-original.pdf
Davies KA, Longshaw CM, Davis GL, Bouza E, Barbut F, Barna Z et al (2014) Underdiagnosis of Clostridium difficile across Europe: the European, multicentre, prospective, biannual, point-prevalence study of Clostridium difficile infection in hospitalized patients with diarrhea (EUCLID). Lancet Infect Dis 14(12):1208–1219
Acalá L, Martín A, Martín M, Sánchez-Somolinos M, Catalân P, Pelâez T et al (2012) The undiagnosed cases of Clostridium difficile infection in a whole nation: where is the problem? Clin Microbiol Infect 18(7):E204–E213
Ooijevaar RE, van Beurden YH, Terveer EM, Goorhuis A, Bauer MP, Keller JJ et al (2018) Update of treatment algorithms for Clostridium difficile infection. Clin Mircobiol Infect. https://doi.org/10.1016/j.cmi.2017.12.022
Krutova M, Kinross P, Barbut F, Hajdu A, Wilcox M, Kuijper E (2017) How to: surveillance of Clostridium difficile infections. Clin Microbiol Infect. https://doi.org/10.1016/j.cmi.2017.12.008
Crobach MJ, Dekkers OM, Wilcox MH, Kuijper EJ (2009) European Society of Clinical Microbiology and Infectious Diseases (ESCMID): data review and recommendations for diagnosing Clostridium difficile-infection (CDI). Clin Microbiol Infect 15(12):1053–1066
Crobach MJ, Planche T, Eckert C, Barbut F, Terveer EM, Dekkers OM et al (2016) European Society of Clinical Microbiology and Infectious Diseases: update of the diagnostic guidance document for Clostridium difficile infection. Clin Microbiol Infect 22:S63–S81
Van Dorp SM, Notermans DW, Alblas J, Gastmeier P, Mentula S, Nagy E et al (2016) Survey of diagnostic and typing capacity for Clostridium difficile infection in Europe, 2011 and 2014. Euro Surveill 21(29). https://doi.org/10.2807/1560-7917.ES.2016.21.29.30292
Barbut F, Surgers L, Eckert C, Visseaux B, Cuignet M, Mesquita C et al (2014) Does a rapid diagnosis of Clostridium difficile infection impact on quality of patient management? Clin Microbiol Infect 20(2):136–144
Alicino C, Giacobbe DR, Durando P, Bellina D, DI Bella AM, Paganino C et al (2016) Increasing incidence of Clostridium difficile infections: result from a 5-year retrospective study in a large teaching hospital in the Italian region with the oldest population. Epidemiol Infect 144(12):2517–2526
Vindigni SM, Surawicz CM (2015) C. difficile infection: changing epidemiology and management paradigms. Clin Transl Gastroenterol 6:e99. https://doi.org/10.1038/ctg.2015.24
Barbut F, Ramé L, Petit A, Suzon L, de Chevigny A, Eckert C (2015) Prevalence of Clostridium difficile infection in hospitalized patients with diarrhea: results of a French prospective multicenter bi-annual point prevalence study. Presse Med 44(4 Pt 1):e75–e83
McDonald LC, Gerding DN, Johnson S, Bakken JS, Carroll KC, Dubberke ER et al (2018) Clinical practice guidelines for Clostridium difficile infection in adults and children: 2017 update by the Infectious Diseases Society of America (IDSA) and Society for Healthcare Epidemiology of America (SHEA). Clin Infect Dis 66(7):e1–e48
Acknowledgements
revogene C. Difficile study group
Johan van Broeck
Michel Delmée
Funding
This study was supported by grants from GenePOC, now part of Meridian Biosciences.
Author information
Authors and Affiliations
Consortia
Corresponding author
Ethics declarations
Conflict of interest
All principal investigators from each site received financial support from GenePOC, now part of Meridian Biosciences, for conference attendance to present their respective data as part of this multicenter evaluation.
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Sambri, V., Gateau, C., Zannoli, S. et al. Diagnosing Clostridioides difficile infections with molecular diagnostics: multicenter evaluation of revogene C. difficile assay. Eur J Clin Microbiol Infect Dis 39, 1169–1175 (2020). https://doi.org/10.1007/s10096-020-03829-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10096-020-03829-4