Abstract
The uniaxial compressive strength (UCS) of rocks is an essential input parameter for engineering design in mining and civil engineering. This research aimed to investigate the relationship between nano-mechanical properties and macroscopic mechanical properties that result from microstructural constituents of rock materials. Grid nanoindentation technique was applied to a small sample volume to measure nano-mechanical properties such as hardness (Hi) and elastic modulus (Ei) of bulk and major mineral constituents of granite and carbonate rocks. The material Hi and Ei were compared to UCS of the rocks and related to their mineral composition and microstructure, which were detected by X-ray diffraction and petrographic thin sections analysis, respectively. The results show that the mean UCS of the investigated materials correlates well with bulk and major mineral hardness and elastic modulus, with granite showing the highest values, followed by limestone and dolomitic marble. The potential correlations between the UCS and Hi and Ei were investigated using simple regression and multiple linear regression analysis. Except for the weak correlations obtained from dolomitic marble (UCS-Ei), the results show noteworthy correlations between UCS-Hi and UCS-Ei with R2 ranging from 81.5 to 97.5% along with good statistical indices (RMSE and VAF), the best correlation being obtained using MLR. Due to constraints associated with the assessment of standard specimens for compression tests as well as existing indirect methods of determining UCS, the indentation test could be considered a potential means to estimate the UCS from pieces of rock for proper design in mining and civil engineering projects.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Aladejare AE (2020) Evaluation of empirical estimation of uniaxial compressive strength of rock using measurements from index and physical tests. Journal of Rock Mechanics and Geotechnical Engineering 12(2):256–268. https://doi.org/10.1016/j.jrmge.2019.08.001
ASTM D2938–95 (1995) Standard test method for unconfined compressive strength of intact rock core specimens. ASTM International, West Conshohocken, PA
ASTM D5731–16 (2016) Standard test method for determination of the point load strength index of rock and application to rock strenght classifications. In ASTM International, West Conshohocken, PA
Bahaaddini M, Hosseinpour Moghadam E (2019) Evaluation of empirical approaches in estimating the deformation modulus of rock masses. Bull Eng Geol Env 78(5):3493–3507. https://doi.org/10.1007/s10064-018-1347-x
Ban H, Karki P, Kim YR (2013) Nanoindentation test integrated with numerical simulation to characterize mechanical properties of rock materials. J Test Evaluation 42(3). https://doi.org/10.1520/JTE20130035
Brown JM, Angel RJ, Ross NL (2016) Elasticity of plagioclase fledpsars. Journal of Geophysical Research: Solid Earth. https://doi.org/10.1002/2015JB012736.Received
Broz ME, Cook RF, Whitney DL (2006) Microhardness, toughness, and modulus of Mohs scale minerals. Am Miner 91(1):135–142. https://doi.org/10.2138/am.2006.1844
Cao J, Gao J, Nikafshan Rad H, Mohammed AS, Hasanipanah M, Zhou J (2021) A novel systematic and evolved approach based on XGBoost-firefly algorithm to predict Young’s modulus and unconfined compressive strength of rock. Engineering with Computers. https://doi.org/10.1007/s00366-020-01241-2
Constantinides G, Ravi Chandran KS, Ulm FJ, Van Vliet KJ (2006) Grid indentation analysis of composite microstructure and mechanics: principles and validation. Mater Sci Eng, A 430(1–2):189–202. https://doi.org/10.1016/j.msea.2006.05.125
Culshaw MG, Ulusay R (eds) (2015) The ISRM suggested methods for rock characterization, testing and monitoring: 2007–2014. Bull Eng Geol Environ 74:1499–1500. https://doi.org/10.1007/s10064-015-0780-3
Eliyahu M, Emmanuel S, Day-Stirrat RJ, Macaulay CI (2015) Mechanical properties of organic matter in shales mapped at the nanometer scale. Mar Pet Geol 59:294–304. https://doi.org/10.1016/j.marpetgeo.2014.09.007
Fan M, Jin Y, Chen M, Geng Z (2019) Mechanical characterization of shale through instrumented indentation test. J Petrol Sci Eng 174:607–616. https://doi.org/10.1016/j.petrol.2018.11.083
Faradonbeh RS, Taheri A, Sousa LR, e, & Karakus, M. (2020) Rockburst assessment in deep geotechnical conditions using true-triaxial tests and data-driven approaches. Int J Rock Mech Min Sci 128(February):104279. https://doi.org/10.1016/j.ijrmms.2020.104279
Freedman D, Diaconis P (1981) On the histogram as a density estimator:L2 theory. Zeitschrift Für Wahrscheinlichkeitstheorie Und Verwandte Gebiete 57(4):453–476. https://doi.org/10.1007/BF01025868
Ghasemi S, Khamehchiyan M, Taheri A, Nikudel MR, Zalooli A (2020) Crack evolution in damage stress thresholds in different minerals of granite rock. Rock Mech Rock Eng 53(3):1163–1178. https://doi.org/10.1007/s00603-019-01964-9
Gowida A, Elkatatny S, Gamal H (2021) Unconfined compressive strength (UCS) prediction in real-time while drilling using artificial intelligence tools. Neural Comput Appl 33(13):8043–8054. https://doi.org/10.1007/s00521-020-05546-7
Graham SP, Rouainia M, Aplin AC, Cubillas P, Fender TD, Armitage PJ (2021) Geomechanical characterisation of organic-rich calcareous shale using AFM and nanoindentation. Rock Mech Rock Eng 54:303–320. https://doi.org/10.1007/s00603-020-02261-6
Haftani M, Bohloli B, Nouri A, Maleki Javan MR, Moosavi M (2014) Size effect in strength assessment by indentation testing on rock fragments. Int J Rock Mech Min Sci 65:141–148. https://doi.org/10.1016/j.ijrmms.2013.10.001
Hyndman RJ, Koehler AB (2006) Another look at measures of forecast accuracy. Int J Forecast 22(4):679–688. https://doi.org/10.1016/j.ijforecast.2006.03.001
ISRM (1981) Rock characterisation testing and monitoring. In: Brown ET (ed) Pergamon press, Oxford, 211pp
ISRM (1989) Rock characterization testing and monitoring: International Society for Rock Mechanics Commission. Ed. E. T. Brown. Pergamon press, pp. 83–88
Jalali SH, Heidari M, Zarrinshoja M, Mohseni N (2019) Predicting of uniaxial compressive strength of some igneous and metamorphic rocks by block punch index and cylindrical punch index tests. Int J Rock Mech Min Sci 119(May):72–80. https://doi.org/10.1016/j.ijrmms.2019.04.013
Jing H, Nikafshan Rad H, Hasanipanah M, Jahed Armaghani D, Qasem SN (2021) Design and implementation of a new tuned hybrid intelligent model to predict the uniaxial compressive strength of the rock using SFS-ANFIS. Engineering with Computers 37(4):2717–2734. https://doi.org/10.1007/s00366-020-00977-1
Karakul H, Ulusay R (2013) Empirical correlations for predicting strength properties of rocks from P-wave velocity under different degrees of saturation. Rock Mech Rock Eng 46(5):981–999. https://doi.org/10.1007/s00603-012-0353-8
Komadja GC, Pradhan SP, Oluwasegun AD, Roul AR, Stanislas TT, Laibi RA, Adebayo B, Onwualu PA (2021) Geotechnical and geological investigation of slope stability of a section of road cut debris-slopes along NH-7 , Uttarakhand , India. Results Eng 10(May). https://doi.org/10.1016/j.rineng.2021.100227
Liu K, Ostadhassan M, Bubach B (2016) Applications of nano-indentation methods to estimate nanoscale mechanical properties of shale reservoir rocks. Journal of Natural Gas Science and Engineering 35:1310–1319. https://doi.org/10.1016/j.jngse.2016.09.068
Liu K, Ostadhassan M, Bubach B (2018) Application of nanoindentation to characterize creep behavior of oil shales. J Petrol Sci Eng 167:729–736. https://doi.org/10.1016/j.petrol.2018.04.055
Lu Y, Li Y, Wu Y, Luo S, Jin Y, Zhang G (2020) Characterization of shale softening by large volume-based nanoindentation. Rock Mech Rock Eng 53(3):1393–1409. https://doi.org/10.1007/s00603-019-01981-8
Maruvanchery V, Kim E (2020) Mechanical characterization of thermally treated calcite-cemented sandstone using nanoindentation, scanning electron microscopy and automated mineralogy. Int J Rock Mech Min Sci 125:104158. https://doi.org/10.1016/j.ijrmms.2019.104158
Munoz H, Taheri A, Chanda EK (2016) Fracture energy-based brittleness index development and brittleness quantification by pre-peak strength parameters in rock uniaxial compression. Rock Mech Rock Eng 49(12):4587–4606. https://doi.org/10.1007/s00603-016-1071-4
Mustafa S, Khan MA, Khan MR, Sousa LMO, Hameed F, Mughal MS, Niaz A (2016) Building stone evaluation-a case study of the sub-Himalayas, Muzaffarabad region, Azad Kashmir, Pakistan. Eng Geol 209:56–69. https://doi.org/10.1016/j.enggeo.2016.05.007
Ojo EB, Bello KO, Ngasoh OF, Stanislas TT, Mustapha K, Savastano H, Soboyejo W (2020) Mechanical performance of fiber-reinforced alkali activated un-calcined earth-based composites. Constr Build Mater 247:118588. https://doi.org/10.1016/j.conbuildmat.2020.118588
Oliver WC (2004) Measurement of hardness and elastic modulus by instrumented indentation: advances in understanding and refinements to methodology. J Mater Res 19:3–20
Oliver WC, Pharr GM (1992) An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J Mater Res 7(6):1564–1583. https://doi.org/10.1557/jmr.1992.1564
Özkan I, Erdem B, Ceylanoğlu A (2015) Characterization of jointed rock masses for geotechnical classifications utilized in mine shaft stability analyses. Int J Rock Mech Min Sci 73:28–41. https://doi.org/10.1016/j.ijrmms.2014.10.001
Sabatakakis N, Koukis G, Tsiambaos G, Papanakli S (2008) Index properties and strength variation controlled by microstructure for sedimentary rocks. Eng Geol 97(1–2):80–90. https://doi.org/10.1016/j.enggeo.2007.12.004
Sajid M, Coggan J, Arif M, Andersen J, Rollinson G (2016) Petrographic features as an effective indicator for the variation in strength of granites. Eng Geol 202:44–54. https://doi.org/10.1016/j.enggeo.2016.01.001
Sayers CM (2008) The elastic properties of carbonates. Leading Edge (tulsa, OK) 27(8):1020–1024. https://doi.org/10.1190/1.2967555
Shirani Faradonbeh R, Taheri A, Karakus M (2022) Fatigue failure characteristics of sandstone under different confining pressures. Rock Mech Rock Eng 55(3):1227–1252. https://doi.org/10.1007/s00603-021-02726-2
Slim M, Abedi S, Bryndzia LT, Ulm F-J (2019) Role of organic matter on nanoscale and microscale creep properties of source rocks. J Eng Mech 145(1):04018121. https://doi.org/10.1061/(asce)em.1943-7889.0001538
Sun C, Li G, Gomah ME, Xu J, Sun Y (2020a) Creep characteristics of coal and rock investigated by nanoindentation. Int J Min Sci Technol 36(6):769–776. https://doi.org/10.1016/j.ijmst.2020.08.001
Sun C, Li G, Zhang S, Xu J, Yang H (2020b) Mechanical and heterogeneous properties of coal and rock quantified and mapped at the microscale. Applied Sciences (switzerland) 10(1):342. https://doi.org/10.3390/app10010342
Taheri A, Zhang Y, Munoz H (2020) Performance of rock crack stress thresholds determination criteria and investigating strength and confining pressure effects. Constr Build Mater 243:118263. https://doi.org/10.1016/j.conbuildmat.2020.118263
Tandon RS, Gupta V (2015) Estimation of strength characteristics of different Himalayan rocks from Schmidt hammer rebound, point load index, and compressional wave velocity. Bull Eng Geol Env 74(2):521–533. https://doi.org/10.1007/s10064-014-0629-1
Ván P, Vásárhelyi B (2014) Sensitivity analysis of GSI based mechanical parameters of the rock mass. Periodica Polytechnica Civil Engineering 58(4):379–386. https://doi.org/10.3311/PPci.7507
Viktorov SD, Golovin YI, Kochanov AN, Tyurin AI, Shuklinov AV, Shuvarin IA, Pirozhkova TS (2015) Micro- and nano-indentation approach to strength and deformation characteristics of minerals. J Min Sci 50(4):652–659. https://doi.org/10.1134/S1062739114040048
Wang M, Wan W (2019) A new empirical formula for evaluating uniaxial compressive strength using the Schmidt hammer test. Int J Rock Mech Min Sci 123(September):104094. https://doi.org/10.1016/j.ijrmms.2019.104094
Whitney DL, Broz M, Cook RF (2007) Hardness, toughness, and modulus of some common metamorphic minerals. Am Miner 92(2–3):281–288. https://doi.org/10.2138/am.2007.2212
Yagiz S (2009) Predicting uniaxial compressive strength, modulus of elasticity and index properties of rocks using the Schmidt hammer. Bull Eng Geol Env 68(1):55–63. https://doi.org/10.1007/s10064-008-0172-z
Zhu W, Hughes JJ, Bicanic N, Pearce CJ (2007) Nanoindentation mapping of mechanical properties of cement paste and natural rocks. Mater Charact 58(11–12):1189–1198. https://doi.org/10.1016/j.matchar.2007.05.018
Acknowledgements
The authors would like to acknowledge the anonymous reviewers for providing constructive comments which have contributed to the improvement of the manuscript. A sincere acknowledgement to Dr. Ojo Emeso for the significant input in enhancing the quality of the presented work.
Funding
This work was supported by the African University of Science and Technology (AUST), Abuja, Nigeria under the Pan African Material Institute (PAMI), and African Development Bank (AfDB) programs. The first author acknowledges the Regional Scholarship Innovation Fund (RSIF-PASET).
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare no competing interests.
Rights and permissions
About this article
Cite this article
Komadja, G.C., Stanislas, T.T., Munganyinka, P. et al. New approach for assessing uniaxial compressive strength of rocks using measurement from nanoindentation experiments. Bull Eng Geol Environ 81, 299 (2022). https://doi.org/10.1007/s10064-022-02801-0
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s10064-022-02801-0