Abstract
Plane strain analytical solutions to estimate purely elastic, partially plastic and fully plastic deformation behavior of rotating functionally graded (FGM) hollow shafts are presented. The modulus of elasticity of the shaft material is assumed to vary nonlinearly in the radial direction. Tresca’s yield criterion and its associated flow rule are used to formulate three different plastic regions for an ideal plastic material. By considering different material compositions as well as a wide range of bore radii, it is demonstrated in this article that both the elastic and the elastoplastic responses of a rotating FGM hollow shaft are affected significantly by the material nonhomogeneity.
Similar content being viewed by others
References
Gere J.M. and Timoshenko S.P. (1990). Mechanics of Materials. PWS-Kent Publishing, Boston
Budynas R.G. (1999). Advanced Strength and Applied Stress Analysis. McGraw-Hill, New York
Lindner T. and Mack W. (1998). Residual stresses in an elastic–plastic shaft with fixed ends after previous rotation. J. Appl. Mathe. Mech. ZAMM 78: 75–86
Gamer U. and Lance R.H. (1983). Stress distribution in a rotating elastic–plastic tube. Acta Mech. 50: 1–8
Mack W. (1991). Rotating elastic–plastic tube with free ends. Int. J. Solids Struct. 27: 1461–1476
Mack W. (1991). The rotating elastic–plastic solid shaft with free ends. Tech. Mech. 12: 119–124
Gamer U., Mack W. and Varga I. (1997). Rotating elastic–plastic solid shaft with fixed ends. Int. J. Eng. Sci. 35: 253–267
Eraslan A.N. (2002). On the linearly hardening rotating solid shaft. Euro. J. Mech. A/Solids 22: 295–307
Eraslan A.N. (2004). Von Mises’ yield criterion and nonlinearly hardening rotating shafts. Acta Mech. 168: 129–144
Eraslan, A.N., Mack, W.: A computational procedure for estimating residual stresses and secondary plastic flow limits in nonlinearly strain hardening rotating shafts. Forschung Im Ingenieurwesen/Eng. Res. 69, 65–75 (2005)
Eraslan A.N. and Akis T. (2006). On the plane strain and plane stress solutions of functionally graded rotating solid shaft and solid disk problems. Acta Mech. 181: 43–63
Akis T. and Eraslan A.N. (2006). The stress response and onset of yield of rotating FGM hollow shafts. Acta Mech. 187: 169–187
Eraslan A.N. and Akis T. (2005). Elastoplastic response of a long functionally graded tube subjected to internal pressure. Turkish J. Eng. Environ. Sci. 29: 361–368
Zimmerman R.W. and Lutz M.P. (1999). Thermal stresses and thermal expansion in a uniformly heated functionally graded cylinder. J. Therm. Stresses 22: 177–188
Horgan C.O. and Chan A.M. (1999). The pressurized hollow cylinder or disk problem for functionally graded isotropic linearly elastic materials. J. Elast. 55: 43–59
Tutuncu N. and Ozturk M. (2001). Exact solution for stress in functionally graded pressure vessels. Composites Pt. B 32: 683–686
Güven U. and Baykara C. (2001). On stress distributions in functionally graded isotropic spheres subjected to internal pressure. Mech. Res. Commun. 28: 277–281
Liew K.M., Kitipornchai S., Zhang X.Z. and Lim C.W. (2003). Analysis of thermal stress behavior of functionally graded hollow circular cylinders. Int. J. Solids Struct. 40: 2355–2380
Sahin A. (2004). An interface crack between a graded coating and a homogeneous substrate. Turkish J. Eng. Environ. Sci. 28: 135–148
Eslami M.R., Babaei M.H. and Poultangari R. (2005). Thermal and mechanical stresses in a functionally graded thick sphere. Int. J. Pressure Vessels Piping 82: 522–527
Timoshenko S.P. and Goodier J.N. (1970). Theory of Elasticity. McGraw-Hill, New York
Mendelson A. (1968). Plasticity: Theory and Application. Macmillan, New York
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Akis, T., Eraslan, A.N. Exact solution of rotating FGM shaft problem in the elastoplastic state of stress. Arch Appl Mech 77, 745–765 (2007). https://doi.org/10.1007/s00419-007-0123-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00419-007-0123-3