Abstract
Post-mortem computed tomography (PMCT) enables the creation of subject-specific 3D head models suitable for quantitative analysis such as finite element analysis (FEA). FEA of proposed traumatic events is an objective and repeatable numerical method for assessing whether an event could cause a skull fracture such as seen at autopsy. FEA of blunt force skull fracture in adults with subject-specific 3D models in forensic pathology remains uninvestigated. This study aimed to assess the feasibility of FEA for skull fracture analysis in routine forensic pathology. Five cases with blunt force skull fracture and sufficient information on the kinematics of the traumatic event to enable numerical reconstruction were chosen. Subject-specific finite element (FE) head models were constructed by mesh morphing based on PMCT 3D models and A Detailed and Personalizable Head Model with Axons for Injury Prediction (ADAPT) FE model. Morphing was successful in maintaining subject-specific 3D geometry and quality of the FE mesh in all cases. In three cases, the simulated fracture patterns were comparable in location and pattern to the fractures seen at autopsy/PMCT. In one case, the simulated fracture was in the parietal bone whereas the fracture seen at autopsy/PMCT was in the occipital bone. In another case, the simulated fracture was a spider-web fracture in the frontal bone, whereas a much smaller fracture was seen at autopsy/PMCT; however, the fracture in the early time steps of the simulation was comparable to autopsy/PMCT. FEA might be feasible in forensic pathology in cases with a single blunt force impact and well-described event circumstances.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
Autopsy and microscopy have remained the forensic pathologists’ most common tools for centuries [1]. With the introduction of post-mortem computed tomography (PMCT) to forensic pathology in the 1970s [2], a new tool became available. The forensic pathology community has since demonstrated how PMCT can be used for diagnostics, screening, identification, foreign object detection, 3D visualization, and 3D printing [3]. This paper aims to demonstrate how data from PMCT may be used for computer simulation of skull fractures to determine the plausibility of a proposed scenario.
The head is of great interest in forensic pathology as it often strikes objects or the ground in accidents and is an obvious target in assaults, and the brain is vulnerable to even small trauma [4]. Blunt force fracture of the neurocranium is seen in 5% of all forensic autopsies in Denmark [5], and almost all forensic cases of skull fracture have suffered lethal brain damage [6]. The skull fracture pattern may provide information on the shape and size of the object that caused the fracture, the number and order of impacts, and the force of the trauma, thus helping forensic pathologists infer the events leading to death [7]. Historically, forensic pathologists have relied on autopsy findings, scientific literature, experience, and available information on the proposed event when analysing skull fractures.
In 2006, finite element analysis (FEA) was introduced in forensic medicine [8, 9], giving forensic pathologists a new, potentially useful tool for skull fracture analysis. FEA is a computational technique often used in engineering to model and analyse complex systems by discretizing objects into a finite number of small elements and solving a series of partial differential equations [10, 11]. FEA enables objective evaluation of the probability of proposed traumatic events. Most head finite element models (FEMs) were developed for research focused on improving traffic safety or preventing traumatic brain injury, and not for forensic investigations [12]. In forensic pathology, FEA of gunshot trauma [13] and blunt force head injury in adults have been attempted [8, 9] using the Université Louis-Pasteur head model [14] and the Royal Institute of Technology’s Kungliga Tekniska Högskolan (KTH) head model [9]. Apart from the study on subject-specific infant skull fracture by Li et al. [15] and the study by Kleiven with analysis of fracture occurrence and -pattern [9], most of the finite element (FE) head models were coarse by modern standards, being comprised of fewer and larger elements than more recent FE head models such as the head model named “A Detailed and Personalizable Head Model with Axons for Injury Prediction” (ADAPT) [16]. More recent attempts with more detailed models were made by Jia et al. [17] and Gao et al. [18]; however, none of these models were subject-specific. Combining PMCT and FEA allows for subject-specific analysis of skull fractures. The 2021 ADAPT head model developed by KTH Royal Institute of Technology is anatomically detailed, can be personalized, and may be feasible for forensic use.
The objective of this study was to evaluate the feasibility of FEA for skull fracture in adults with subject-specific 3D FEMs obtained from PMCT and only the information available in routine cases as a tool in forensic pathology. For this, five cases of blunt force skull fracture involving falls from the department’s routine cases were simulated. Subject-specific versions of the ADAPT FEM, originally presented in [16], and later enhanced with an improved strain-rate dependent cranial material model [19], were used.
Methods
This section describes how suitable cases were identified, the necessary information about the traumatic event was determined, subjects’ PMCT images were segmented, segmented subjects’ images were morphed to the ADAPT model leading to subject-specific FE head models, and FEA performed.
Case identification
In a prior study, we had established a database of 250 deceased persons with blunt force skull trauma who were autopsied at the Department of Forensic Medicine at the University of Copenhagen between 2013 and 2019 [20]. From this database, we identified five cases suitable for FEA. The following criteria were used: (1) the deceased was an adult, (2) PMCT data of the head were available, (3) the event had only a single impact and a relatively simple skull fracture, (4) autopsy reports allowed assumptions of body movement at the traumatic event to estimate impact point and kinematics, and (5) police reports allowed event reconstruction to substantiate impact point and kinematics. Though the FEA itself is objective, the inclusion criteria 3 through 5 necessitated a partly subjective evaluation prior to analysis, the consequences of which will be discussed.
Cases, traumatic events, and scene parameters
The cases are described superficially to avoid identification, and only information relevant to the traumatic event and scene parameters is described here. Four skulls had simple, linear fractures in the occipital bone caused by falls from standing or low-speed traffic accidents. One case had more extensive fractures of the frontal bone from fall from height. In three cases, the cause of death was acute ischaemic heart disease or subarachnoid haemorrhage due to vascular malformation. In three cases, the deceased fell limp to the ground from a standing position and these impacts resulted in the cranial fractures, whilst in the remaining two cases, death was a result of injuries sustained in the traumatic event.
From a combination of PMCT, police reports, autopsy reports, and hospital records, if such were included in the police reports, a junior doctor and an experienced forensic pathologist inferred the events at injury and impact point to the head. Subsequently, and in line with generally accepted methods, the impact angle and velocity of the head were determined with personalized FE human body models [21, 22], accounting for age, sex, height, and weight [19]. The subject information is summarized in Table 1.
PMCT data
PMCT data were acquired with a Siemens Somatom Definition (Siemens Medical Solutions, Forchheim, Germany) using parameters listed in Table 2. The tube current varied due to automatic dose modulation.
3D segmentation of PMCT
The first step was to generate subject-specific 3D head models with the layers: (1) combined dense connective tissue scalp (skin) and soft tissue scalp (fat), (2) outer and inner table of cortical bone, (3) diploë, and (4) intracranial volume. This was done by segmentation of the PMCT images using 3D Slicer (v.4.11) [23]. In cases with extensive injury, craniotomy, or foreign bodies such as pressure gauges, the contra-lateral side was used as a basis for segmentation by mirroring the CT images as symmetry between the two halves of the skull was assumed. The facial bones and facial soft tissues were not segmented, and a mass corresponding to the mass of the missing face was later added to the models for FE using a semi-automated approach described below.
Subject-specific head model creation
The above segmented subject-specific 3D head models were combined with the ADAPT FEM to create subject-specific FEMs that preserved the subject-specific geometry and thickness of the skulls. This combination of subject and FEM is referred to as morphing and the process has previously been described in detail by Li [24]. Summarizing the morphing process, the subject-specific models were aligned with the ADAPT model in 3D Slicer (v.4.10.2) and registered with the module BRAINSdemonWarp [25] from which displacement fields representing the anatomical difference between the subjects and the baseline ADAPT FE model were obtained. The displacement fields were then used to morph the baseline ADAPT, leading to subject-specific head models. The ADAPT FE model is based on the ICBM152, an “average” head constructed from MRI scans of 152 adults [26]. The baseline ADAPT FE head model is shown in Fig. 1, demonstrating the elements. The ADAPT FE head model includes cortical bone, diploë, meninges, cerebrospinal fluid, and distinct anatomy of the brain as a conforming, continuous mesh with hexahedral elements varying in size from 0.5 to 2.5 mm and a minimum Jacobian value of 0.45 [16].
Finite element analysis and material properties
LS-DYNA (v.13: Livermore, CA, USA) and LS-PrePost (v.4.8: Livermore, CA, USA—Ansys LS-DYNA | Crash Simulation Software) were used for FEA and post processed in MATLAB (v2021a: The 251 MathWorks Inc, MA, USA). In the FEA, elements that reached their breaking point were deleted. For details, see Eqs. 1 and 2 in Lindgren et al. [27]. In all cases, the ground was modelled as an elastic material with parameters as specified in Table 3.
The ADAPT finite element model assumed the adult skull bone to be brittle, elastic-plastic, strain-rate dependent, and isotropic [19]. The scalp was modelled locally with two layers, the outer representing skin and the inner representing dense connective tissue with values previously used by Fahlstedt et al. [28]. We assumed neither sex nor age differences in the mechanical properties of tissues once individual thickness and geometry had been accounted for [29], and the sutures were not included in the ADAPT FEM. The material properties are described in detail in a previous publication [19].
Results
3D segmentation and geometrical accuracy of the subject-specific models
The relatively intact skulls were segmented with automatic tools in 3D Slicer in less than 5 h whilst the most damaged skulls required up to 15 h of additional manual segmentation. To quantify how well the subject-specific head models created through morphing represented the geometry of the real skulls (i.e. the segmented 3D PMCT), the point-to-point distance between the 3D PMCT model of each subject and the morphed subject-specific FE head model was calculated and visually demonstrated in a heat-map (see Fig. 2). Besides, DICE values were calculated to further quantify the accuracy, as presented in Table 4. Finally, the mesh quality of the subject-specific FE head models was quantified in terms of minimum Jacobian (Table 4), showing quality of subject-specific FE models comparable with baseline model quality.
FEA of skull fractures for all cases
The finite element analysis of each case took about 6 h to complete on a supercluster with 128 cores. The results varied from correct fracture pattern in the correct location to the correct pattern in the wrong location to the wrong pattern in right location. Figures 3, 4, 5, 6, 7, 8, and 9 depict the fracture lines as seen at autopsy, on PMCT 3D volume rendering technique (VRT), and as simulated with FEA.
In cases 1 and 2, the fracture lines seen at autopsy and those simulated were nearly identical in location and pattern. In case 3, the simulation predicted a short horizontal fracture line at the impact point, and the simulation predicted a fracture line closer to the midline than the fracture observed at autopsy. The overall patterns of a linear fracture originating at the impact point, progressing into the skull base, and terminating in the middle fossae were comparable. In case 4, linear fractures of comparable extend and similar point of origin were predicted by simulation and seen at autopsy, however in different places, as the simulated fracture extended upwards in the calvaria and the fracture observed at autopsy ran in the skull base. In case 5, the simulation was initially identical to the fracture seen at autopsy, but the simulation progressed to a more severe spider-web pattern. FEA was performed in sequential time steps in the order of milliseconds, and if the FEA was stopped early, the initial simulated fracture resembled the actual linear fracture.
Discussion
In this paper, we evaluated the feasibility of FEA of blunt force skull fracture in adults in forensic pathology. We used subject-specific 3D models generated from PMCT data and the information available in routine forensic pathology cases and demonstrated that it was possible to simulate fractures resembling the real fractures in three of five cases. We will discuss the methods, results, and the applicability of FEA in forensic pathology.
FEA in forensic pathology requires PMCT for two reasons: (1) to create the subject-specific FEMs, and (2) to help infer the circumstances of the traumatic event by drawing attention to potential bone fractures in the extremities and of the facial skeleton, which are locations not routinely dissected at autopsy [30]. To further substantiate the circumstances and head kinematics, information available in the standard police reports or documents included in the police reports such as hospital records and autopsy data are necessary, as external lesions such as abrasion, lacerations, and contusions and internal lesions such as fractures or dislocations may provide information that allows estimation of the kinematics and body movements during the traumatic event. For this study, we only included cases where the above-mentioned data were available; thus, the partly subjective inclusion criteria may bias the results favourably to FEA, as only cases assumed to be possible to simulate were included.
The segmentation process was automated as much as possible to obtain some objectivity, repeatability, and documentability. However, as with the subjective nature of input parameters, human decision-making in segmentation will influence the shape and thickness of the 3D head model. This decision-making is evident in dealing with e.g. partial volume effect, as also noted by de Kegel et al. [31].
The creation of subject-specific FE head models with hexahedral elements directly from PMCT data is challenging and time consuming [31]. Alternatively, an automated voxel-based solution may be used, but it results in jagged edges which in turn results in less accurate simulation. In this study, the subject-specific 3D models were created with a semi-automatic approach in 3D Slicer and then morphed with the ADAPT FEM, reducing the needed work time and maintaining relatively good accuracy as quantified with DICE (Table 4) and distance (Fig. 2) and thus potentially making subject-specific FEA more feasible in routine forensic pathology. A weakness of subject-specific head models based on post-injury CT is that intact 3D models without bone loss or foreign objects were necessary for FEA, as the inclusion of either would result in weaknesses causing a self-fulfilling fracture simulation. This makes FEA impossible in cases of severe fracture with displacement of comminuted fractures.
FEA requires a continuous shape to be discretized into a finite number of elements such as hexahedrals. The process of converting the irregular shape of the subjects’ skulls into a FE model into, e.g. hexahedral elements, is called meshing. The minimum Jacobian expresses the quality of the elements that constitute the FE model. Ideally, all elements should have the shape they were intended to, for example brick or hexahedral. When the elements are morphed to the shape of the subject-specific segmentation in the morphing step, some elements are geometrically distorted. The Jacobian ranges from − 1 to 1, where one represents perfectly shaped elements and values below zero indicate severely distorted elements. The DICE coefficient quantifies the difference between the segmented subject-specific images with image representing the ADAPT FE model, thus the resemblance between the subject’s skull and the subject-specific FE model. The DICE ranges from 0 to 1, where one represents a perfect fit between segmentation and subject-specific FEM, and zero represents a subject-specific FEM with no geometrical resemblance to the segmentation [32]. The minimum Jacobian in this study ranged from 0.12 to 0.31, indicating a relatively good quality of the mesh in the generated subject-specific models, helpful for stable running of FEA, and in line with commonly accepted values for “good” morphing and meshing [33]. The DICE varied from 0.87 to 0.90, indicating that the generated models accurately represented the subjects.
The bio-fidelity of the ADAPT FE head model used in this study was previously evaluated by Lindgren et al. against experimental test in uniaxial tension, skullcap indentation loading, and performed well in predicting fractures in terms of fracture initiation and propagation compared to real-world data [19]. This sets the skull model apart from other subject-specific head models [31, 34,35,36] of which only one has been evaluated against experimental data for fracture [35]. The assumptions regarding material properties of head models differ [31, 35], though most are valid and based on experimental testing of human bone. Naturally, the models cannot be expected to behave identically when based on different assumptions. However, this underscores that biological variation and a lack of consensus values may be a challenge to FEA. Subject-specific FE head models may be the first step in overcoming this challenge and subject-specific, heterogeneous bone density a further step.
In cases 1 and 2, and to some extent in case 3, the fractures were simple linear fractures, the event circumstances were well described, and the involved area of the skull had a low point-to-point distance between the subject and FEM. In these cases, fractures were correctly predicted by FEA. In case 4, the direction of fracture propagation in the simulated fracture was not consistent with the actual fracture. However, a linear fracture of comparable dimension was predicted. Skull fractures begin away from the impact due to bevelling and propagate back towards the impact point [37]. In the FEA, we used erosion meaning that elements were deleted as they reached breaking point. This deletion of elements influences the mechanical behaviour of the remaining elements, and the “wrong” fracture propagation may have been a self-fuelling process initiated by the deletion of the first wrongly predicted elements. Uncertainties regarding the initial angular velocities and the assumption of homogeneous skull properties for both cortical bone and diploë may partly explain the wrongful fracture propagation prediction. With only slightly lower bone density in the inferior parts of the occipital bone, the fracture might have propagated in that direction instead. A sensitivity study, substituting case 4 for cases with thinner skull bone for the occipital area, demonstrated fracture propagation inferiorly [19], which supports the speculation that case 4 might have had lower density of the occipital bone than assumed by the material model used. In case 5, the early time steps of the simulated fracture were largely consistent with the real fracture. However, the full simulation overpredicted the fracture and there was difference between the FEA and the real fracture. Based on the crack patterns observed by Gurdjian et al. in their stresscoat studies [38], we speculate that perhaps the force in the FEA was too high. As sensitivity studies showed, lesser force would have resulted in a less extensive fracture pattern [19]. In case 5, the deceased survived for an extended period, potentially masking some fractures as they potentially healed, thus artificially contributing to FEA “overpredicting”. The 3D segmentation assumed bilateral symmetry of the skull; thus, the potential effects of the craniotomy on subject-specific FEM generation could be ignored. The differences in fracture patterns between the simulation and the real fracture may be a result of the uncertainties regarding how much the deceased cushioned the fall and how much force the face and facial bones absorbed. In our simulation, no such absorption by the face was assumed. Cases 3, 4, and 5 underscore the partly subjective nature of the otherwise objective FEA in that segmentation and input parameters are influenced by human decisions. However, these are explicitly documented. But even with access to accurate kinematic measurements from controlled experimental studies, it has proved difficult to correctly predict fracture lines [31]. In this study, the initial head kinematics were derived from subject-specific multi-body models positioned in accordance with information gathered from police reports and autopsy [19]. As such, common for all studies is the approach of an educated guess for initial kinematics [8, 9, 17, 18]. Considering the uncertainty regarding the kinematics in forensic cases, great caution should be taken when using finite element analysis in a forensic setting, as even small changes in model parameters and event kinematics change the outcome of the simulation markedly [27, 31, 39,40,41,42,43], and even though FEA is on the cusp of potentially aiding forensic pathologists, technical challenges still warrant caution when interpreting the results. However, the assumptions and decisions are explicitly documented in the FEA and thus subject to scrutiny, discussion, and revision.
Jia et al. presented the results of the simulations as time-stress curves and values indicated that the stress from contact with the ground could cause fractures whilst the force from contact with the car was insufficient to cause any fractures. Jia et al. did not present the actual fracture seen at autopsy but noted that FEA demonstrated a linear fracture in the occipital bone in “about the same spot” [17]. Gao et al. concluded that FEA may be used for fracture line determination, but did not provide images for comparison of actual fracture and simulated fracture [18]. In Kleiven’s study, the fracture pattern was not investigated per se, and the results were ambiguous, demonstrating that a fracture could occur but would most likely not [9]. Raul et al. noted that “The anatomical distribution of the deleted elements is close to the fracture seen at autopsy, yet is not very accurate”. [8]. The ADAPT FE head model used in this study consists of about 4,950,000 elements, making it one of the FE head models with the most and smallest elements, allowing for very detailed fracture propagation prediction. Additional elements would result in a definite increase in computation time. It has been argued that simplified models could be sufficient [44], though it has also previously been argued that more elements may improve the quality of FEA [45]. Coarse FE head models with fewer and lager elements may be sufficient to predict if fracture occurs, but finer FE models with more and smaller elements are necessary for fracture propagation prediction. The downside to fine models is the need for significant computational capabilities such as the need for high-performance computing facilities. The question remains, given the inherent assumptions regarding event kinematics, whether FEA should be used for fracture pattern prediction or only for predicting fracture occurrence.
Potential applications of FEA in forensic pathology may include cases of multiple head traumas to determine which traumas could cause skull fracture. This was relevant in case 1 where the cause of death was natural, and the skull fracture occurred during the events leading to death. However, the deceased had also fallen prior to death and this first fall had not caused a skull fracture. Raul et al. simulated a comparable scenario, trying to distinguish between two falls as cause of death [8], and Jia et al. had previously investigated whether a motorcycle crash or subsequent collision with a car caused skull fracture [17]. In case 1, other evidence and autopsy findings allowed the determination of which fall had caused the skull fracture, but in cases in which other objective findings do not allow this determination, then FEA could guide further investigation: should the simulation result in either no fracture, extensive fractures, or a markedly different fracture pattern, then the forensic pathologist might have to consider other scenarios than those proposed. In case 2, the speed of the cyclist who struck the deceased was known from the police investigation. However, FEA may be used to approximate the speed of the involved parties in accidents by varying input parameters until the simulated fracture resembles the fracture seen at autopsy. This use is comparable to a study by Deng et al. who determined the angle and velocity necessary to cause skull fracture in falls [39]. Likewise, in case 3, the forensic pathologist was asked to determine whether death was an accidental fall or natural death resulting in a fall. FEA of the skull assuming a “limp” person falling from standing could help demonstrate that the skull fracture could have originated from a fall with an impact to the occipital region due to acute ischemic heart disease, and not from a fall with higher energy or a fall where the person had managed to cushion the blow to the head. It may be difficult for laypersons to understand that a fall from standing can cause skull fracture, despite it being well described [46]. FEA may help close speculations about interpersonal violence and bring closure to the relatives. Though not demonstrating the actual fracture precisely in case 3, FEA indicated that this specific person could have suffered a skull fracture when collapsing from natural death.
Conclusion
In this study on the feasibility of subject-specific FEA in routine cases of blunt force skull fracture in adults, we demonstrated that FEA may be used in select cases to augment the basis for forensic pathologists’ analyses and conclusions. FEA is currently only feasible in cases with well-described events with simple kinematics and relatively intact skulls. As our cases also showed, caution should be taken when using FEA in a forensic setting.
This study was limited by the assumptions regarding the kinematics of the traumatic events and the fact that the ADAPT model has not been evaluated against cadaver studies with known kinematics. Future studies may perform validation against experimental tests or continue to simulate real cases, preferably with known kinematics, of different impact locations and events with different trauma mechanisms. This will help clarify the “error rate” for FEA in forensic pathology. Traumatic events captured by CCTV or other forms of video would provide a means to obtain more certain kinematics.
Data availability
The data on cases are not available due to confidentiality.
Code availability
The code for morphing is available through [24].
References
Benivieni A (1507) De abditis nonnullis ac mirandis morborum et sanationum causis. Florence, Springfield, p 217
Wullenweber R, Schneider V, Grumme T (1977) A computer-tomographical examination of cranial bullet wounds [German]. Z fur Rechtsmedizin J Legal Med 80:227–246. https://doi.org/10.1007/bf02114619
Grabherr S, Egger C, Vilarino R, Campana L, Jotterand M, Dedouit F (2017) Modern post-mortem imaging: an update on recent developments. Forensic Sci Res 2:52–64. https://doi.org/10.1080/20961790.2017.1330738
Gill JR (2022) Adelson’s The pathology of homicide: a guide for forensic pathologists and homicide investigators (2nd edn). Charles C. Thomas Publisher, Limited, p 794
Jacobsen C (2008) Cranial fractures caused by blunt trauma to the skull - a retrospective analysis of medico-legal autopsies in Denmark from 1999–2004. Scand J Forensic Sci 14:64–70
Carson HJ (2009) Brain trauma in head injuries presenting with and without concurrent skull fractures. J Forensic Leg Med 16:115–120. https://doi.org/10.1016/j.jflm.2008.08.013
Puppe G (1903) Traumatische Todesursachen. G. Fischer, Gerichtl Med 12:65–84
Raul JS, Baumgartner D, Willinger R, Ludes B (2006) Finite element modelling of human head injuries caused by a fall. Int J Legal Med 120:212–218. https://doi.org/10.1007/s00414-005-0018-1
Kleiven S (2006) Biomechanics as a forensic science tool: Reconstruction of a traumatic head injury using the finite element method. Scand J Forens Sci 2:73–78
Liu WK, Li S, Park HS (2022) Eighty years of the finite element method: birth, evolution, and future. Arch Comput Methods Eng 29:4431–4453. https://doi.org/10.1007/s11831-022-09740-9
Hrennikoff A (2021) Solution of problems of elasticity by the framework method. J Appl Mech 8:A169–A75. https://doi.org/10.1115/1.4009129
Madhukar A, Ostoja-Starzewski M (2019) Finite element methods in human head impact simulations: a review. Ann Biomed Eng 47:1832–1854. https://doi.org/10.1007/s10439-019-02205-4
Raul JS, Deck C, Meyer F, Geraut A, Willinger R, Ludes B (2007) A finite element model investigation of gunshot injury. Int J Legal Med 121:143–146. https://doi.org/10.1007/s00414-005-0070-x
Willinger R, Kang HS, Diaw BM (1999) Développement et validation d’un modèle mécanique de la tête humaine. C R Acad Sci - Ser IIB - Mechanics-Physics-Astronomy 327:125–31. https://doi.org/10.1016/S1287-4620(99)80021-0
Li X, Sandler H, Kleiven S (2019) Infant skull fractures: Accident or abuse? Evidences from biomechanical analysis using finite element head models. Forensic Sci Int 294:173–182. https://doi.org/10.1016/j.forsciint.2018.11.008
Li X, Zhou Z, Kleiven S (2021) An anatomically detailed and personalizable head injury model: significance of brain and white matter tract morphological variability on strain. Biomech Model Mechanobiol 20:403–431. https://doi.org/10.1007/s10237-020-01391-8
Jia M, Li Z, Zhang J et al (2020) Finite element analysis to determine the cause of ring fractures in a motorcyclist’s head. Leg Med (Tokyo) 45:101697. https://doi.org/10.1016/j.legalmed.2020.101697
Gao W, Bai Z, Li H, Liu Y, Chou CC, Jiang B (2020) A study on cyclist head injuries based on an electric-bicycle to car accident reconstruction. Traffic Inj Prev 21:563–568. https://doi.org/10.1080/15389588.2020.1821882
Lindgren N, Henningsen MJ, Jacobsen C, Villa C, Kleiven S, Li X (2023) Prediction of skull fractures in blunt force head traumas using finite element head models. Biomech Model Mechanobiol. https://doi.org/10.1007/s10237-023-01768-5
Henningsen MJ, Harving ML, Jacobsen C, Villa C (2022) Fractures of the neuro-cranium: sensitivity and specificity of post-mortem computed tomography compared with autopsy. Int J Legal Med 136:1379–1389. https://doi.org/10.1007/s00414-022-02779-0
Hamel A, Llari M, Piercecchi-Marti MD, Adalian P, Leonetti G, Thollon L (2013) Effects of fall conditions and biological variability on the mechanism of skull fractures caused by falls. Int J Legal Med 127:111–118. https://doi.org/10.1007/s00414-011-0627-9
O’Riordain K, Thomas PM, Phillips JP, Gilchrist MD (2003) Reconstruction of real world head injury accidents resulting from falls using multibody dynamics. Clin Biomech (Bristol Avon) 18:590–600. https://doi.org/10.1016/s0268-0033(03)00111-6
Fedorov A, Beichel R, Kalpathy-Cramer J et al (2012) 3D slicer as an image computing platform for the quantitative Imaging Network. Magn Reson Imaging 30:1323–1341. https://doi.org/10.1016/j.mri.2012.05.001
Li X (2021) Subject-specific head model generation by mesh morphing: a personalization framework and its applications. Front Bioeng Biotechnol 9. https://doi.org/10.3389/fbioe.2021.706566
Johnson H (2009) BRAINSDemonWarp: an applicaton to perform Demons Registration. Insight J 1. https://doi.org/10.54294/ib7or9
Fonov VS, Evans A, McKinstry R, Almli CR, Collins D (2009) Unbiased nonlinear average age-appropriate brain templates from birth to adulthood. NeuroImage 47
Lindgren N, Henningsen MJ, Jacobsen C, Villa C, Kleiven S, Li X (2023) Prediction of skull fractures in blunt force head traumas using finite element head models. Biomech Model Mechanobiol. https://doi.org/10.1007/s10237-023-01768-5
Fahlstedt M, Depreitere B, Halldin P, Vander Sloten J, Kleiven S (2015) Correlation between injury pattern and finite element analysis in biomechanical reconstructions of traumatic brain injuries. J Biomech 48:1331–1335
Lynnerup N, Astrup JG, Sejrsen B (2005) Thickness of the human cranial diploe in relation to age, sex and general body build. Head Face Med 1:13. https://doi.org/10.1186/1746-160x-1-13
Leth PM, Ibsen M (2010) Abbreviated injury scale scoring in traffic fatalities: comparison of computerized tomography and autopsy. J Trauma 68:1413–1416. https://doi.org/10.1097/TA.0b013e3181b251b8
De Kegel D, Meynen A, Famaey N, van Harry G, Depreitere B, Sloten JV (2019) Skull fracture prediction through subject-specific finite element modelling is highly sensitive to model parameters. J Mech Behav Biomed Mater 100:103384. https://doi.org/10.1016/j.jmbbm.2019.103384
Dice LR (1945) Measures of the amount of ecologic association between species. Ecology 26:297–302. https://doi.org/10.2307/1932409
Li Z, Hu J, Reed MP et al (2011) Development, validation, and application of a parametric pediatric head finite element model for impact simulations. Ann Biomed Eng 39:2984–2997. https://doi.org/10.1007/s10439-011-0409-z
Ji S, Zhao W, Ford JC et al (2015) Group-wise evaluation and comparison of white matter fiber strain and maximum principal strain in sports-related concussion. J Neurotrauma 32:441–454. https://doi.org/10.1089/neu.2013.3268
Huang J, Raymond DE, Shen W, Stuhmiller JH, Crawford G, Bir C (2011) Development and validation of a subject-specific finite element model for skull fracture assessment. ASME 2011 International Mechanical Engineering Congress and Exposition, pp 31–40. https://doi.org/10.1115/IMECE2011-63682
Tse KM, Tan LB, Lee SJ, Lim SP, Lee HP (2014) Development and validation of two subject-specific finite element models of human head against three cadaveric experiments. Int J Numer Method Biomed Eng 30:397–415. https://doi.org/10.1002/cnm.2609
Lissner HR, Gurdjian ES, Webster JE (1949) Mechanism of skull fracture as studied by the stresscoat. J Mich State Med Soc 48:217
Gurdjian ES, Webster JE, Lissner HR (1950) The mechanism of skull fracture. Radiology 54:313–339. https://doi.org/10.1148/54.3.313
Deng X, Du Z, Feng H, Wang S, Luo H, Liu Y (2022) Investigation on the modeling and reconstruction of head injury accident using ABAQUS/Explicit. Bioeng (Basel) 9. https://doi.org/10.3390/bioengineering9120723
Elliott JR, Simms CK, Wood DP (2012) Pedestrian head translation, rotation and impact velocity: the influence of vehicle speed, pedestrian speed and pedestrian gait. Accid Anal Prev 45:342–353. https://doi.org/10.1016/j.aap.2011.07.022
Alvarez VS, Halldin P, Kleiven S (2014) The influence of neck muscle tonus and posture on brain tissue strain in pedestrian head impacts. Stapp Car Crash J 58:63–101. https://doi.org/10.4271/2014-22-0003
Paas R, Davidsson J, Brolin K (2015) Head kinematics and shoulder biomechanics in shoulder impacts similar to pedestrian crashes–a THUMS study. Traffic Inj Prev 16:498–506. https://doi.org/10.1080/15389588.2014.968778
Giudice JS, Zeng W, Wu T, Alshareef A, Shedd DF, Panzer MB (2019) An analytical review of the numerical methods used for finite element modeling of traumatic brain injury. Ann Biomed Eng 47:1855–1872. https://doi.org/10.1007/s10439-018-02161-5
Kemmoku DT, Serenó L, San J, Ciurana J (2014) A novel simplified 3D skull model to predict cranial fracture patterns. Int J Comput Integr Manuf 27:927–935. https://doi.org/10.1080/0951192X.2013.834470
Asgharpour Z, Baumgartner D, Willinger R, Graw M, Peldschus S (2014) The validation and application of a finite element human head model for frontal skull fracture analysis. J Mech Behav Biomed Mater 33:16–23. https://doi.org/10.1016/j.jmbbm.2013.02.010
Hartshorne NJ, Harruff RC, Alvord EC Jr (1997) Fatal head injuries in ground-level falls. Am J Forensic Med Pathol 18:258–264. https://doi.org/10.1097/00000433-199709000-00006
Acknowledgements
The simulations were performed on resources provided by the Swedish National Infrastructure for Computing (SNIC) at the PDC Center for High Performance Computing at the KTH Royal Institute of Technology. Thank you to Kasper Hansen Aarhus University for assisting in segmentation. We would like to thank the anonymous reviewers for their helpful suggestions and comments.
Funding
Open access funding provided by Copenhagen University. This study was based on funding from the University of Copenhagen.
Author information
Authors and Affiliations
Contributions
CV and CJ conceived the study. MJH and CV wrote the protocol with assistance from SK and XL. MJH identified relevant cases, developed the segmentation algorithm, and performed the segmentation. MJH and CJ analysed the traumatic events leading to skull fracture and determined impact points. SK and XL previously developed the ADAPT head model. XL created the morphing algorithm. MJH and XL morphed the subject-specific masks to the ADAPT model. NL defined and validated material models and properties for finite element analysis. NL performed the finite element analysis under the supervision of SK and XL. MJH wrote the first draft. All authors contributed scientifically to the manuscript and approved it.
Corresponding author
Ethics declarations
Ethics approval
Per Danish law, this study was exempt from ethical approval as it was based on registry data. The University of Copenhagen approved the data plan on behalf of the Danish Data Protection Agency (514–0644/21-3000).
Conflict of interest
The authors declare no competing interests.
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Below is the link to the electronic supplementary material.
ESM 1
(DOCX 22.0 KB)
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Henningsen, M.J., Lindgren, N., Kleiven, S. et al. Subject-specific finite element head models for skull fracture evaluation—a new tool in forensic pathology. Int J Legal Med 138, 1447–1458 (2024). https://doi.org/10.1007/s00414-024-03186-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00414-024-03186-3