Abstract
The automation in fabrication of CFRP (carbon-fiber-reinforced plastics) parts demands efficient and low-cost machining technologies. In conventional cutting technologies, tool-wear and low process speeds are some of the reasons for high costs. Thus, the use of lasers is an attractive option for cutting CF-preforms. A typical effect degrading the quality in laser cutting CF-preform is a bulged cutting edge. This effect is assumed to be caused by interaction of the fibers with the ablated material, which leaves the kerf at high velocity. Hence, a method for measuring the momentum and the velocity of the vapor is presented in this article. To measure the momentum of the ablated material, the CF-preform is mounted on a precision scale while cutting it with a laser. The direction of the momentum was determined by measuring the momentum parallel and orthogonal to the CF-preform surface. A change of the direction of the momentum with different cutting-speeds is assessed at constant laser-power. Averaged velocities of the ablation products of up to 300 m/s were determined by measuring the ablated mass and the momentum.
Similar content being viewed by others
References
W. Hufenbach, W. Biermann, G. Seliger, Serientaugliche Bearbeitung und Handhabung moderner Faserverstärkter Hochleistungswerkstoffe – Untersuchungsbericht zum Forschungs- und Handlungsbedarf (Progressmedia Verlag u Werbeagentur, Dresden, 2008). ISBN/EAN: 978-3-00-026217-3
V. Lopresto, L. Santo, G. Caprino, I. De Iorio, Effect of fiber orientation on cutting forces and cut quality in machining UD CFRP, in 4th AITEM Congress (1999), pp. 451–458
G. Caprino, I. De Iorio, L. Nele, L. Santo, Effect of tool wear on cutting forces in the orthogonal cutting of UD GFRP. Composites, Part A, Appl. Sci. Manuf. 27A, 409–415 (1996)
G. Caprino, V. Tagliaferri, Maximum cutting speed in laser cutting of fiber reinforced plastics. Int. J. Mach. Tools Manuf. 28, 389–398 (1988)
A. Goeke, C. Emmelmann, Influence of laser cutting parameters on CFRP part quality. Phys. Procedia 5, 253–258 (2010)
P.W. French, M. Naeem, J. Clowes, M.C. Sharp, Fiber laser material processing of aerospace composites, in Proceedings of the Fifth International WLT-Conference on Lasers in Manufacturing, Munich (AT-Fachverlag, Stuttgart, 2009)
R. Weber, M. Hafner, A. Michalowksi, T. Graf, Minimum damage in CFRP laser processing. Phys. Procedia 12(2), 302–307 (2011)
A. Wolynski, H. Haloui, P. Mucha, A. Gleite, P. French, R. Weber, T. Graf, Effect of process strategies on thermal load during CFRP processing, in Proc. ICALEO, Los Angeles (2010)
K.T. Voisey, S. Fouquet, D. Roy, T.W. Clyne, Fiber swelling during laser drilling of carbon fiber composites. Opt. Lasers Eng. 44, 1185–1197 (2006)
P. Mucha, Studienarbeit IFSW 10-37 (2010)
P. Mucha, Diplomarbeit IFSW 11-20 (2011)
O. Meyer, Kurzfaser-Preform-Technologie zur kraftflussgerechten Herstellung von Faserverbundbauteilen, Universität Stuttgart, Institut für Flugzeugbau, Dissertation (2008)
C.J. Knight, Theoretical modeling of rapid surface vaporization with back pressure. AIAA J. 17(5), 519–523 (1979)
D. Breitling, A. Ruf, P.W. Berger, F.H. Dausinger, S.M. Klimentov, P.A. Pivovarov, T.V. Kononenko, V.I. Konov, in Laser Processing of Advanced Materials and Laser Microtechnologies: Conf. on Lasers, Applications, and Technologies LAT, Moscow, Proc. SPIE, vol. 5121, ed. by F.H. Dausinger, V.I. Konov, V.Yu. Baranov, V.Ya. Panchenko (SPIE Press, Bellingham, 2002), pp. 24–33
D. Grojo, J. Hermann, A. Perrone, Plasma analysis during femtosecond laser ablation of Ti, Zr and Hf. J. Appl. Phys. 97, 063306 (2005)
E. Hecht, Optik (Addison-Wesley, Bonn, 1989)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Mucha, P., Speker, N., Weber, R. et al. Momentum and velocity of the ablated material in laser machining of carbon fiber preforms. Appl. Phys. A 113, 361–366 (2013). https://doi.org/10.1007/s00339-013-7629-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00339-013-7629-z