Abstract
Dimensional analysis is a simple, clear and intuitive method for determining the functional dependence of physical quantities that are of importance to a certain process. Buckingham’s pi theorem is used to derive a dimensionally homogeneous equation for predicting the discharge of the microtube as a function of gravitational acceleration (g), microtube diameter (D), operating pressure head (H) and microtube length (L). Experimental investigations were conducted at College of Agricultural Engineering and Technology, Junagadh, to determine (a) the variation in Q with L, D and H and (b) the coefficients (K, y and z) of the developed model. The L and D of microtube were varied from 5 to 250 cm and 1.2 to 2 mm. The operating pressure was varied from 0 to 1.5 m. The L, H and D combinations selected in the study suit most of the manufacturer’s recommendations for microtube drip irrigation systems. The discharge of microtube decreased with increase in microtube length for particular microtube diameter and operating pressure. The discharge increased with increase in the microtube diameter for a particular operating pressure and microtube length. The values of K, y and z are 4.476, 1 and 0.5, respectively. Goodness of fit and efficiency coefficient reduced with increase in the microtube diameter. The dimensionally homogeneous equation (Eq. 25) developed for all flow regimes can predict discharge with good accuracy for less than 2-mm microtube diameter. The microtube diameter was found to be 1.2 mm based on the dominance of viscous forces over inertial forces.
Similar content being viewed by others
References
Allen RG (1996) Relating the Hazen-Williams and Darcy-Weisbach friction loss equations for pressurized irrigation systems. Appl Eng Agric 12:685–693
Anyoji H (1986) Comprehensive design of drip irrigation lines in a submain unit. Bull Natl Res Inst Agric Eng 25:153–209 (Japan)
Boswell MJ (1985) Design characteristics of line-source drip tubes. In: Proceedings of the third international drip/trickle irrigation congress, vol I. California, USA, pp 306–312
Bralts VF, Wu IP (1979). Emitter flow variation and uniformity for drip irrigation. ASAE Paper No. 79-2099, p 34 ASAE, St. Joseph, MI
Bralts VF, Wu IP, Gitlin HM (1981) Manufacturing variation and drip irrigation uniformity. Trans ASAE (N.S.) 24(1):119–133
Braud HJ, Soon AM (1980) Trickle irrigation lateral design on sloping fields. Trans ASAE 24:941–944, 950
Buckingham E (1914) On physically similar systems: illumination of the use of dimensional equations. Phys Rev 4(4):345
Demir V, Yurdem H (2002) Ayni damlaticiya sahip damla sulama borularinda boru capinin en uygun boru uzunluguna etkisi. Ege Universitesi Ziraat Fakultesi Dergisi 39:120–127
Demir V, Uz E (1999) A research on the determination of the technical properties and frictional losses of the components used in micro irrigation systems. In: Proceedings of 7th international congress on mechanization and energy in agriculture, pp 84–89, Adana
Dogan E, Kirnak H (2010) Water temperature and system pressure effect on drip lateral properties. J Irrig Sci 28(5):407–419
Dov N (2000) Drip irrigation. In: Finkel HJ (ed) CRC Handbook of irrigation technology. CRC Press Inc, Boca Raton, FL, USA
Hezarjaribi A, Dehghani A, Helghi MM, Kiani A (2008) Hydraulic performance of various trickle irrigation emitters. J Agron 7(3):265–271
Howell TA, Barinas FA (1980) Pressure losses across trickle irrigation fittings and emitters. Trans ASAE 23:928–933
Howell TA, Aljibury FK, Gitlin HM, Wu IP, Warrick AW, Raats PAC (1983) Design and operation of trickle (Drip) systems. In: Jensen ME (ed) Design and operation of farm irrigation systems. ASAE Monograph, No. 3, St. Joseph, Michigan
Kadale AS, Narda NK, Singh A (1992) Discharge rate of microtube emitters as influenced by water temperature variation. J Res Punjab Agric Univ 29(2):245–248
Karmeli D (1977) Classification and flow regime analysis of drippers. J Agric Eng Res 22:165–173
Khatri KC, Wu IP, Gitlin HM, Philips AL (1979) Hydraulics of microtube emitters. J Irrig Drain Eng ASCE 105(2):163–173
Langhaar HL (1987) Dimensional analysis and theory of models. Robert E Kreiger Publisher Company Inc., NY
Liang GC, O’Connor KM, Kachroo RK (1994) A multiple inlet single output variable gain factor model. J Hydrol 155:185–198
Mallikarjuna P, Suresh Babu Ch, Mohan Reddy JA (2009) Simulation of monthly stream flow using linear regression and ANN models. ISH J Hydraulic Eng 15(2):131–144
Nash JE, Sutcliffe JV (1970) River flow forecasting through conceptual models Part 1-A discussion of principles. J Hydrol 10:282–290
Solomon K, Bezdek JC (1980) Simulated flow rate requirements for some flushing emitters. ASAE and CSAE national meeting on trickle (drip) irrigation, paper no. 79-2571, Winnipeg, Canada
Vekariya PB (2000) Studies on high discharge drip irrigation system for summer groundnut. Thesis submitted for partial fulfillment of M Tech to Gujarat Agricultural University, Junagadh
Watters GZ, Keller J (1978) Trickle Irrigation Tubing Hydraulics. ASAE Paper No. 78-2015, p 18. ASAE, St. Joseph, Michigan
Wu IP, Gitlin HM (1977) Drip irrigation system design. Trans ASAE 2:3–19
Wu IP, Gitlin HM, Solomon KH, Saruwatari CA (1986) Design principles-system design. In: Nakayama GS, Bucks DA (eds) Trickle irrigation for crop production. Elsevier Science Publishers, Netherlands
Wu IP, Feng J, Yabusaki K (1989) Emitter spacing and uniformity of irrigation application. ASAE Paper No. 89-2080, P 16, St. Joseph, MI
Acknowledgments
The authors are thankful to the anonymous reviewers for their valuable comments on improving the quality of paper.
Author information
Authors and Affiliations
Corresponding author
Additional information
Communicated by A. Kassam.
Rights and permissions
About this article
Cite this article
Vekariya, P.B., Subbaiah, R. & Mashru, H.H. Hydraulics of microtube emitters: a dimensional analysis approach. Irrig Sci 29, 341–350 (2011). https://doi.org/10.1007/s00271-010-0240-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00271-010-0240-6