Abstract
Food contact materials (FCM) may contain complex mixtures of estrogenic chemicals. A yeast estrogen screen performed on high performance thin-layer chromatography plates (planar-YES, P-YES) is promising for analysis of such mixtures, as it could allow for better elucidation of effects compared with established methods in microtiter plates. However, the P-YES has not been directly compared with established methods. We compared the performance of a microtiter plate YES (lyticase-YES, L-YES) to P-YES on silica gel HPTLC plates using 17β-estradiol (E2), 20 chemicals representative of migrants from plastic FCM, and three migrates of coated metal food cans. Effective doses (ED10, ED50) and estradiol equivalencies were calculated for each chemical. Thirteen chemicals had calculable EDs in the L-YES or P-YES, with average EDs 13-fold (range 0.63–36) more potent in P-YES than in the L-YES. Normalized to E2, the median estrogenicity was within 1.5-fold (0.43–8.8) between the assays. Therefore, P-YES was as or more sensitive than L-YES but potencies relative to E2 were comparable between assays. With chromatography, the P-YES detected estrogenicity in coated metal cans, effects that were unmeasurable in L-YES. With the sample preparation methods used in this study, both YES assays are sufficiently sensitive to detect bisphenol A below the specific migration limit for plastic packaging (0.05 mg/kg food). This study demonstrates that P-YES outperforms L-YES because it is more sensitive, provides comparable estradiol equivalents, and circumvents confounding mixture effects. The P-YES will be useful for routine monitoring of FCM and toxicant identification in problematic materials.
![](http://media.springernature.com/lw685/springer-static/image/art%3A10.1007%2Fs00216-020-02701-w/MediaObjects/216_2020_2701_Figa_HTML.png)
Graphical abstract
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
Food packaging can contribute potentially toxic chemicals to food. In the European Union, chemicals known to be reproductive toxicants are not allowed to be used in plastic food packaging [1], although some endocrine-disrupting chemicals are still associated with plastic packaging [2]. Food contact materials (FCM) used in packaging products can be a source of estrogenic chemicals to food [3]. Migration of known chemicals into food can be monitored with target chemical analysis. However, unintentional chemicals can also be present in the final packaging and may migrate to food. Therefore, methods to detect and identify toxic non-intentionally added substances (NIAS) are necessary beyond target analysis for known chemicals.
Bioassays are used to measure chemical mixtures for biological effects, so do not target specific chemicals. Bioassays for dioxin-like chemicals are allowed for screening of certain foodstuffs [4]. Bioassays are therefore potential tools to monitor for bioactive NIAS that can migrate from FCM [3, 5]. For samples with bioactivity, a combination of chemical fractionation and (bio)analysis, i.e., effect-directed analysis (EDA), is useful to elucidate the responsible toxicants [6, 7]. One important class of chemicals potentially coming from FCM is (xeno)estrogens, for which there are several types of bioassays. Commonly used are in vitro reporter gene assays that measure the activation of an estrogen receptor [8]. One such assay is the yeast estrogen screen (YES).
The YES employs yeast containing a plasmid with the human estrogen receptor, h-ERα, linked to lacZ gene that codes for β-galactosidase [9]. The response to a chemical or mixture is then measured with a substrate for β-galactosidase whose product results in a colored or fluorescent signal. A standardized 96-well plate format of the YES performed with enzyme (lyticase)-assisted digestion is referred to here as the L-YES [10]. In such reporter gene assays, mixture components can cause cytotoxicity which can mask transactivation [5]. To handle interfering cytotoxicity, Escher et al. recommend running parallel cell viability assays and limiting dose-response modeling to low, non-cytotoxic concentrations [11]. This is successful if cytotoxicity only occurs at concentrations greater than observable target effects, e.g., h-ERα induction.
Bioassays are also possible on high performance thin-layer chromatography (HPTLC) plates. Such methods may first perform chromatographic separation of a chemical mixture using TLC. Then, an in vitro bioassay is performed on the HPTLC plate where it can be possible to distinguish target effects from cytotoxicity [12,13,14,15]. This combination of sample separation and bioassay is well suited to an EDA framework [6, 12, 16]. For example, the retention factor of bioactive zones can be matched with those of known chemicals to help identify responsible toxicants, and active zones can be extracted for further evaluation with mass spectrometry. The yeast estrogen screen is one of the most established assays in HPTLC format [12,13,14, 17, 18]. Referred to here as planar-YES (P-YES, and specifying with or without chromatography), it has been used for analyses including wastewater [14, 15], river sediment [14], herbal extracts [19], and personal care products [12], but until recently is still undergoing development in data collection [17, 18] and evaluation [20, 21].
Previous work comparing P-YES to other assays has focused on steroidal estrogens. Könemann et al. found that results of P-YES correlated well to human cell-based transactivation assays for surface and wastewater samples [22], although a 96-well plate YES was not included in their comparisons. The study focused on three steroidal estrogens commonly detected in surface and waste water samples, for which predicted effects (based on chemical analysis of three target estrogens) matched the bioassay results well. Klingelhöfer and Morlock also compared the potency (relative to 17β-estradiol, E2) of 17α-ethinyl estradiol in P-YES to literature values of a microtiter well plate version of YES with good agreement (0.3 to 0.47, respectively) [18]. It is still unknown how P-YES differs from microtiter plate assays for a broader range of chemicals, specifically those that are relevant to FCM. Differences in assay details, such as silica or polystyrene plate material, could have chemical-specific effects on bioassay results [23].
With the aim of further establishing P-YES for bioassay screening and EDA of FCM, this study compares the P-YES to a 96-well plate-based L-YES. Our specific goals were to (1) define the relative sensitivities of P-YES and L-YES to several estrogenic chemicals related to FCM, (2) understand any discrepancies between the assays by evaluating assay parameters, and (3) evaluate the performance of these two assays for migrates from real FCM. Results from this work will help to establish the P-YES as a tool for analysis of single chemicals and complex mixtures such as FCM.
Materials and methods
Materials
HPLC-grade ethanol, methanol, n-hexane, acetone, petroleum ether, chloroform, and silica gel 60 HPTLC plates were purchased from Merck (Darmstadt, Germany). Lyticase, dithiothreitol, chlorophenol red-β-d-galactopyranoside (CPRG), and 4-methylumbelliferyl-β-d-galactopyranoside (MUG) were obtained from Sigma-Aldrich (St. Louis, Mo, USA). A solution (lacZ buffer) was prepared with 10.67 g/L Na2HPO4-2H2O, 0.75 g/L KCl, 0.25 g/L MgSO4-7H20, and 1 g/L sodium dodecyl sulfate (all from Sigma-Aldrich). We selected chemicals for screening based on their reported presence in food packaging materials and for their potential estrogenicity [24,25,26]. Table 1 lists the test chemicals, and their sources and purity, which include four phenols, three bisphenols, three phthalates, and two benzophenones.
Estrogen screening
Yeast (S. cerevisiae of “McDonnell” [27] or “Sumpter” [28] strains) was stored as concentrated stock cultures, at 900–1400 formazine attenuation units (FAU, a measure of cell density), in 20% glycerol at − 80 °C until bioassays were performed. Yeast stock cultures were used to inoculate growth media 22 ± 1 h before starting the bioassays. Cell density was measured with a microtiter plate absorbance reader (BioTek Synergy 2, Winooski, VT, USA) at 600 nm. Yeast were prepared for L-YES and P-YES in exposure media according to an ISO standard [10] and Schönborn et al. [17].
L-YES
The L-YES procedure followed an ISO standard [10] in 96-well plates. Ethanolic solutions of test chemicals were serial diluted over eight wells, then evaporated to dryness. Eighty microliters of nanopure water was added to each well and shaken for 5 min at 500 rpm. Then, 40 μL of yeast at a density of 25 FAU was added to each well; the plates were covered with breathable seals and incubated at 30 °C for 18 ± 1 h. After incubation, the cells were re-suspended and cell density was recorded. Aliquots (30 μL) of yeast were transferred from the wells of the test plate to a new 96-well plate and 50 μL of 0.4 mg/mL CPRG solution with 250 U/mL lyticase and 1 mM dithiothreitol in lacZ buffer was added to each well. After an incubation of 1 h at 30 °C, absorbance was measured at 580 nm.
High performance thin-layer plate preparation and chromatography
HPTLC plates (20 × 10 cm, or 10 × 10 cm in some tests without chromatography) were prepared by developing them with methanol in a twin-trough chamber then drying in an oven at 110 °C for 30 min. Chemicals, prepared in ethanol, were applied in up to 20 μL per band to HPTLC plates with an Automated TLC Sampler 4 (CAMAG, Muttenz, CH) as 6 mm bands starting 20 mm from the left edge, and track distance at least 18 mm. Additional plate layout and application parameters are given in Electronic Supplementary Material (ESM) Tables S1 and S2. For tests without chromatography, application of chemicals was randomly assigned along three rows at 15, 42.5, and 70 mm on each plate. We used chromatography only in experiments to compare its effect on the potency of E2, the reference chemical for both YES assays and bisphenol A (BPA), as described in the ESM (Fig. S8), and when testing migrates of FCM. In these cases, HPTLC plates were developed to 80 mm with an Automated Multiple Development 2 (AMD2, CAMAG) using preconditioning with 1.2% NH3, isocratic chromatography with a solvent mixture of chloroform:acetone:petroleum ether 11:5:5 [17, 29], and dried under vacuum for 2 min. For experiments described in this study, P-YES was performed without chromatography unless otherwise specified (as “P-YES with chromatography”).
P-YES
Performance of the P-YES was based on Schönborn et al. [17]. Yeast was adjusted to 1000 ± 200 FAU in fresh exposure medium. With an automated spraying chamber, Derivatizer (CAMAG) with red nozzle and spraying level six, 2 mL of yeast culture was sprayed onto HPTLC plates before or after chromatography. The HPTLC plates were incubated for 3 h at 30 °C in plastic boxes with water-saturated paper towels to maintain humidity above 80%. After incubation, the plates were dried with a hair dryer set on low heat and fan speed for 3–5 min. The indicator, 2 mL 0.5 mg/mL MUG in lacZ buffer, was then sprayed onto the plates with the Derivatizer (blue nozzle, level six) and plates were incubated at 37 °C for 20 min. The plates were dried again with a hair dryer. For cases in which fluorescent signal on a plate was uniformly less than expected, plates were exposed to NH3 vapor, which enhanced the signal of the fluorescent product of MUG, 4-methylumbelliferone (4-MU) [13, 30]. Images were collected with the TLC Visualizer (CAMAG) with illumination at 366 nm for 550 ms and processed for peak height and area with VisionCats v2.4 (CAMAG).
Chemical testing
Twenty chemicals were evaluated in duplicate in 10-fold dilution series for range-finding in L-YES and P-YES. The highest concentrations were 1 mM in L-YES. The moles of chemical in 1 mM in L-YES (final volume 120 μL) were applied as the highest level in P-YES. Fourteen chemicals were determined active in range-finding tests. To capture the full dose-response curves, these chemicals were tested again in the L-YES and P-YES with 2-fold dilutions in suitable concentration ranges (ESM Table S3) based on the range-finding tests.
The effect of chromatography on sensitivity of the assays was evaluated for E2 and BPA. Briefly, E2 and BPA concentration series were applied, with randomized tracks, to part of an HPTLC plate, and developed in the AMD2. Then, the chemicals were applied in randomized tracks to the remaining part of the HPTLC plate. The P-YES proceeded on the HPTLC plates as described above, and analyzed as described below.
Sample preparation
Food contact articles were donated by the Cantonal Laboratory of Zurich and Swiss Quality Testing Services (SQTS). All samples were metal cans with internal coating. From SQTS, a fish can was selected because it had previously displayed estrogenic activity in P-YES with chromatography [31]. Duplicate cans received 95% ethanol:water and were sealed with the original lids and PTFE tape (Sigma-Aldrich), with no internal standards added. The duration of the migrations lasted for 10 days at 60 °C. Two glass beakers, sealed and handled in the same way, were used as migration controls. Food can migrates were concentrated 20-fold by evaporation with constant stream of nitrogen in a 40 °C water bath using Turbovap LV (Biotage, Uppsala, SWE), to a final volume of 1 mL. They were tested up to 2.4 mL migrate equivalents (120 μL concentrated migrate) in L-YES and up to 0.8 mL migrate equivalents (40 μL concentrated migrate) in P-YES with chromatography. The bioassay and detection were performed as described above.
Quality control and data analysis
The potency of E2 was monitored over time and was stable for experiments included in this study (see ESM Figs. S1 and S2). Solvent and migration controls were inactive in both bioassays. The format of P-YES (chemical application to HPTLC plates and solvent evaporation) prohibits calculation of a concentration-based dose. Therefore, for both assays, the number of moles per replicate, i.e., moles per application zone or moles per well in P-YES and L-YES respectively, was used as a dose metric.
Dose-response modeling of P-YES results was performed with R using the package drc 3.0-1 [32]. P-YES dose-response modeling consisted of the following. Peak height of E2 was modeled as a 4-parameter log logistic regression (Eq. 1) for each replicate plate. Then, height of E2 and test chemicals was normalized to the modeled top E2 response for each plate. Replicates were combined and modeled again with Bottom constrained to zero (Eq. 2). Based on examination of model residuals, logarithm of response was used to comply with the modeling assumption of constant variance, and a constant was added to allow log transformation of zero values. Absorbance at 580 nm measured in triplicate wells in the L-YES was corrected for the average absorbance of ethanol controls. The data were normalized to the modeled top E2 value (Eq. 1) and modeled with Eq. 2, without log-transformed response (GraphPad Prism 7, San Diego, CA, USA). Treatments that caused less than 80% of the average cell growth of ethanol controls, as measured with absorbance at 600 nm, were omitted from analysis.
Median or 10% effective doses (ED50 or ED10, respectively) and 95% confidence intervals were determined from interpolation of dose-response curves at 50 and 10% of normalized E2, e.g., at y = log(50 + 1) using Eq. 2. Estradiol equivalency factors (EEFs) were determined when possible as the ratio of ED50s of E2 to corresponding test chemicals for each experiment (Eq. 3). ED10 was used to calculate chemical EEF when ED50 from at least one bioassay was incalculable, e.g., due to low maximum response.
Results and discussion
P-YES is more sensitive than L-YES
Based on previous publications [17, 33] and our own preliminary work, the most sensitive methods, i.e., appropriate yeast strain, for performing L-YES and P-YES were used to analyze chemicals associated with FCMs. The reference compound, E2, was more potent in P-YES than L-YES by about 10-fold (Fig. 1 and ESM Fig. S2).
Example dose-response curves used in the calculation of ED50 and ED10, which are indicated by vertical dashed lines. The responses are peak height for P-YES and optical density at 580 nm for L-YES. Replicates are three HPTLC plates (one replicate concentration series per plate) or three wells of a microtiter plate (three replicate concentration series per plate) for P-YES and L-YES, respectively. E2, 17β-estradiol; BPA, bisphenol A
Thirteen chemicals had calculable effect concentrations for at least the 10% level in either L-YES or P-YES (Fig. 2, ESM Table S4). Full dose-response curves are shown in ESM Fig. S3. Diisobutyl phthalate, which is not shown in Fig. 2, showed slight induction in the L-YES but below ED10. An ED10 was calculable from both assays for 11 chemicals, and an ED50 was calculable in both assays for six chemicals. Benzyl butyl phthalate and 2,2′-dihydroxy-4-methoxybenzophenone had poor responses in L-YES, with a maximum induction of less than 50% of the E2 maximum.
Estrogenicity of chemicals related to FCM in the L-YES and P-YES. (a) Ten percent, and (b) median, effect concentrations (ED10 and ED50, respectively) with 95% confidence intervals (n = 3–4). Error bars are often hidden by the data marker. (c) Relative potency as normalized to the reference compound E2 (17β-estradiol equivalency factor, EEF). Center values are shown for only chemicals for which EEFs in both assays could be calculated. EEFs in gray shading were calculated with ED10 instead of ED50 for chemicals that did not reach 50% effect level
The active chemicals were on average 13-fold (range 0.63–36) more potent in P-YES than L-YES. Previous testing of single chemicals showed similar findings in yeast-based assays. Our determined ED50s of 2,4-bis(1-methyl-1-phenylethyl) phenol and benzene, 1,1′-(1,3-propanediyl)bis- in the L-YES were very similar to previous values determined in a YES performed in microtiter plates, while the P-YES produced EDs closer to those determined with ERα-CALUX [34]. Harris et al. found an EEF of 1 × 10−6 and 1 × 10−7 for benyzl butyl phthalate and diisobutyl phthalate, respectively [35]. In comparison, we found the L-YES EEF for butyl benzyl phthalate to be about 5 × 10−6, and the modeled top values of these phthalates were 50% or less of the modeled E2 top, as has also been previously observed [35, 36]. Compounds that were inactive in both L-YES and P-YES also corroborate previous findings, for example, 2,4-tert-butylphenol, butylated hydroxytoluene, and diethylhexyl adipate were not active at concentrations tested by Mertl et al. [34] or Simon et al. [37].
The variability of the P-YES was always greater than the L-YES. The dose-response curves of E2 and BPA had larger confidence intervals in the P-YES than the L-YES (Fig. 1). The variability of P-YES results is also apparent for the other test chemicals in the ED10 and ED50 confidence intervals (Fig. 2) and full dose-response models (ESM Fig. S3). However, we challenged the P-YES by using three HPTLC plates as replicates compared with the ISO L-YES, in which replicates were on the same microtiter plate. In this way, some, but probably not all, of the variability differences can be explained.
EEFs are similar despite different assay formats
In general, we observed good agreement in EEF between L-YES and P-YES. The assays produced similar results when normalized to the reference chemical, E2, as EEF (Fig. 2c). The median EEF was 1.2 (range 0.43–8.8) times greater in the L-YES than for P-YES. The Pearson correlation of EEFs between the P-YES and L-YES was 0.89 (Fig. 3). This suggests that differences between tested chemicals and assay format do not have a big effect on quantification of estrogenicity. This is surprising as the availability to yeast cells could depend on the plate materials and format of the bioassay. Both the microtiter and HPTLC plate assays include a similar step in which test chemicals and samples are applied to a plate in organic solvent and dried. The test substance is then re-dissolved in water or medium when a solution is added to the microtiter wells or the yeast suspension is sprayed onto the HPTLC plate, respectively. However, plate materials (polystyrene in L-YES, silica in P-YES) have different affinities for test chemicals which could affect their availability in exposure medium [38]. The clearest trend in chemical responses was decreasing agreement in EEF between L-YES and P-YES with decreasing potency (Fig. 2). Effect concentrations were not easily modeled for chemicals with lower potency due to low maximum responses (e.g., benzyl butyl phthalate) or reduced cell growth (e.g., 2,2′-dihydroxy-4-methoxybenzophenone). Correlation between estrogenic activity and Henry’s law, octanol-air, or octanol-water coefficients was poor (Pearson’s correlation ≤ 0.5). A larger suite of chemicals might be able to elucidate subtle differences between assays. However, we did notice that the agreement between P-YES and L-YES seems to hold until potency approaches water solubility in the L-YES (ESM Fig. S4). Water solubility in P-YES is not calculable because the volume in which chemicals are dissolved is unknown. A specific case is for 2,2′-dihydroxy-4-methoxybenzophenone which has similar water solubility and L-YES potency as 2-hydroxy-4-methoxybenzophenone but did not produce a response at 10% effect in P-YES. This is possibly explained by greater inhibitory effects (halo in P-YES or reduced cell growth in L-YES) of 2,2′-dihydroxy-4-methoxybenzophenone than 2-hydroxy-4-methoxybenzophenone. Overall, while P-YES and L-YES show good consensus, the agreement might break down as one or both assays reach physical limits such as water solubility.
Estradiol equivalency factors (EEF) for chemicals that tested positive in the L-YES and P-YES. Dashed line represents 1:1. Based on EDs as described in Fig. 2. P value for Pearson correlation (r) = 0.00031
Many assay parameters do not explain different sensitivities
This study used two different yeast strains for the P-YES (“McDonnell”) [27] and L-YES (“Sumpter”) [28]. This difference was based on established protocols [10, 17], and we investigated the performance of the strains in both assays. The ED50 of the reference chemical, E2, was lower for Sumpter than McDonnell yeast in the L-YES. The background response was also lower for Sumpter yeast than McDonnell (ESM, Fig. S5). Both strains produced similar responses to 20 food contact chemicals tested in the L-YES (ESM, Fig. S6). Therefore, the strains do not have major inherent differences in their response to different chemicals. In the P-YES, Sumpter yeast produced a much weaker response than McDonnell, so was not used to evaluate the whole suite of chemicals. Sumpter yeast requires media enriched with more amino acids than McDonnell. It is possible that nutrients are not as available on HPTLC plates as when dissolved in wells of a microtiter plate. This would allow the more self-sufficient McDonnell yeast to thrive better than Sumpter yeast on HPTLC plates.
As mentioned in the previous section, some chemicals produced a “halo” or “corona” effect in P-YES (see ESM, Fig. S7). The halo is characterized by a ring of fluorescence around an inactive zone (or activity below baseline). This has been attributed to cytotoxicity [12], and to fluorescence quenching [39]. The two benzophenones were among those that produced halos in P-YES. Benzophenones are used as blockers of ultraviolet (UV) light in consumer products, and other chemicals naturally fluoresce under UV. Because detection of 4-MU, the fluorescent product in the P-YES, requires illumination at 366 nm, these chemical properties may interfere with the results of the test. Therefore, the benzophenones were also tested with CPRG as an indicator solution. The same degree of halo was observed with CPRG as with MUG (e.g., ESM, Fig. S7) so there was no obvious effect of UV blocking causing the differences observed between P-YES and L-YES. Müller et al. observed a 20-fold smaller lowest observed effect level with MUG than CPRG as indicators for YES on HPTLC plates [13]. To test how these indicators affect sensitivity, the L-YES was performed with MUG as well as CPRG. The ED50 of E2 was an average of 1.3 (SD = 0.35, n = 3) times lower for a 1 h incubation with MUG or CPRG (ESM Table S5). Thus, indicator solution alone does not explain the differences observed for greater sensitivity in the P-YES.
Samples, including migrates from FCM, can contain chemicals that have native fluorescence at wavelengths that could interfere with MUG fluorescence. With HPTLC, estrogenic chemicals can be separated from native fluorescence, elucidating bioactivity in a sample that might be hidden when testing the whole sample, as with the L-YES. Samples can also have color which could affect measurement with CPRG. An alternative is resorufin-β-d-galactopyranoside, producing an orange fluorescent signal, which has been used on HPTLC plates to detect E2 down to 3.5 pg/zone (1.3 × 10−14 mol/zone) [21].
Chromatography, which is used in most cases before bioassays on HPTLC plates, may affect the quantitative results, for example, through diffusion of chemicals into the plate. Because this study focuses on effects of the bioassay format (microtiter vs HPTLC plates) between L-YES and P-YES, most experiments were done without chromatography. We also evaluated the effect of one chromatography method on quantitation of E2 and BPA as model chemicals (described in ESM for Fig. S8). The ED50s of E2 and BPA (moles with 95% confidence interval) were 1.1 × 10−15 (9.1 × 10−16–1.4 × 10−15) and 2.0 × 10−11 (1.5 × 10−11–2.6 × 10−11) without chromatography (P-YES), and 2.0 × 10−15 (1.7 × 10−15–2.4 × 10−15) and 2.5 × 10−11 (1.9 × 10−11–3.3 × 10−11) with chromatography. In this direct comparison, the confidence intervals for E2 with and without chromatography do not overlap, suggesting a significant difference. However, both ED50s, E2 with and without chromatography, are within the variability of values measured in the rest of this study (ESM Figs. S1 and S8) and consistently lower than the E2 ED50 in L-YES. Spira et al. [14] and Riegraf et al. [40] observed higher effective doses with chromatography than without, for a P-YES and an HPTLC-based algae bioassay, respectively. These studies used similar, isocratic, chromatography methods as in the current work. They differed, however, in the application method of cells, test species, and/or measurement of effect, any of which might contribute to seeing effects of chromatography [14, 40]. In this study, we intended to focus on the intrinsic differences between the microtiter and HPTLC plate formats of the two yeast assays. There may be combinations of target analyte, sample matrix, chromatography, and bioassay detection that affect the sensitivity of an HPTLC bioassay. Our results show that the P-YES is intrinsically more sensitive than the L-YES, and chromatography will not universally reduce the sensitivity of the bioassay.
Quantifying with area instead of height does not affect the test outcome
To comply with modeling assumptions, we evaluated P-YES data in this study using peak height [20]. However, area under the curve might be more appropriate to compare chemicals if they have different peak shapes. Therefore, we investigated the effect of using area on this study’s outcome. Possibly from diffusion of chemicals on HPTLC plates, we observed continuously increasing areas which is a problem for defining top values of the reference compound E2. Others have observed the same, including on reverse phase-wettable HPTLC plates and with multiple yeast densities [20]. This also leads to violation of modeling assumptions of constant variance. Although if we ignore the modeling violations, the same conclusions are reached with area as with height: P-YES is more sensitive but yields similar EEF when compared with L-YES (ESM Fig. S9).
P-YES reveals estrogenicity of food contact materials where L-YES does not
Three migrates of coated metal cans were evaluated in the L-YES and P-YES with chromatography. Images of P-YES with chromatography for the sample with the strongest response (fish can) are highlighted in Fig. 4, showing bands of native (unknown) and spiked (xeno)estrogen. In L-YES, these migrates produced only slight induction (below 10% of the maximum E2 response), if at all. The highest concentrations of two samples resulted in reduced cell density compared with controls (ESM Fig. S10 and Fig. S11). The same samples showed zones of estrogenicity in P-YES with chromatography (ESM Fig. S12). Fish can migrates showed a strong induction in a band near the solvent front. Therefore, we conclude that the detection of xenoestrogens in the fish can was obscured by low cell growth in the L-YES.
Detection of native and spiked (xeno)estrogens in a migrate of lined metal can (fish can). Lane 1: positive control mixture of (bottom to top) 17β-estradiol (1 pg), 17α-ethinyl estradiol (1 pg), and estrone (10 pg). Retention factor shown on the left. Lane 2: native fish can migrate, 0.4 mL migrate equivalents. Lane 3: fish can migrate spiked with three (xeno)estrogens. Lane 4: Control migrate spiked with three (xeno)estrogens. Zones marked with (a) native fluorescence of chemicals (i.e., not estrogenicity), (b) native estrogenicity, (c) co-retained spiked chemicals estrone (0.2 ng) and 2-hydroxy-4-methoxybenzophenone (140 ng), (d) bisphenol A (27 ng)
We have not determined the identity(ies) of the estrogenic substance(s) in the migrates. Although not the purpose of this study, we could further investigate toxicants detected with P-YES by extracting them for chemical analysis such as non-target high-resolution mass spectrometry [41]. Then, retention factors of standards (if available) from P-YES with chromatography can be used for confirmation. Toxicant identification can be time and resource intensive in the effort to determine the structure of one unknown estrogenic chemical [6]. An alternative, if the chemical’s identity remains unknown, is to quantify the bioassay effect relative to a reference compound. Bioassays to determine bioanalytical equivalents are allowed in determination of dioxin-like activity in food [4]. Similarly, estradiol equivalencies (EEQs) have been applied toward threshold-based screening of water samples [42]. EEQs derived using a version of P-YES with chromatography were shown to correlate well with EEQs from human cell line assays [22].
The specific migration limit for BPA was recently lowered from 0.6 to 0.05 mg/kg food [43]. We used the migration conditions for the fish cans in this study to determine if the L-YES and P-YES are sufficiently sensitive to detect BPA at the updated limit. We assumed a contact ratio of 6 dm2/kg food [1] and used 1.9 dm2 as the estimated internal surface area of the cans, which contacted 80 mL of solvent during migration. Using these assumptions, we calculated a necessary detection limit of BPA as 0.2 mg/L migrate. When we applied 0.8 mL migrate equivalents to the HPTLC plates (40 μL of 20× concentrated migrate) and assuming 100% recovery during sample preparation, we needed to therefore be able to detect 0.2 μg (9 × 10−10 mol) in the bioassay. Both L-YES (BPA ED10, 2.0 × 10−10 mol) and P-YES (BPA ED10, 9.8 × 10−12 mol) are sufficiently sensitive to detect BPA under these conditions. In addition, we demonstrate that BPA was detected when spiked in the fish can migrate at a level of 1.2 × 10−10 mol (27 ng) per band (Fig. 4). However, it should be considered that sample matrix could impact band shape, ultimately affecting quantitation.
Conclusions and recommendations
The P-YES was more sensitive than the L-YES, and is capable of revealing estrogenic effects which might be concealed when testing the whole complex mixture, as in the L-YES. The L-YES was more precise than the P-YES in measuring the dose-response curves of individual chemicals, but both assays produced similar relative potencies, EEFs. We expect these findings will be relevant for other in vitro bioassays performed on HPTLC plates. However, with the relatively small number of test chemicals, range of physicochemical parameters occupied by estrogens, and the variability in methods used for HPTLC bioassays, more data will be needed to confirm our results in other tests and analyte combinations. The L-YES may be easier to implement for laboratories already performing microtiter assays and little experience with HPTLC. Standardization of HPTLC bioassay methods would support transferability of P-YES methods. Our aim was not an easy assay but one that reveals toxicity in complex mixtures. For this, and greater sensitivity, our experience demonstrates that HPTLC bioassays are worth considering for incorporation into routine analysis of NIAS in FCM and other complex mixtures.
Data availability
The datasets generated during the current study are available from the corresponding author on request, and will be available at https://opendata.eawag.ch/.
References
European Commission. Commission Regulation (EU) No 10/2011 on plastic materials and articles intended to come into contact with food. Official Journal of the European Union. 2011.
Groh KJ, Backhaus T, Carney-Almroth B, Geueke B, Inostroza PA, Lennquist A, et al. Overview of known plastic packaging-associated chemicals and their hazards. Sci Total Environ. 2019;651(Pt 2):3253–68.
Kirchnawy C, Mertl J, Osorio V, Hausensteiner H, Washüttl M, Bergmair J, et al. Detection and identification of oestrogen-active substances in plastic food packaging migrates. Packag Technol Sci. 2014;27(6):467–78.
European Commission. Commission Regulation (EU) 2017/644 laying down methods of sampling and analysis for the control of levels of dioxins, dioxin-like PCBs and non-dioxin-like PCBs in certain foodstuffs and repealing Regulation (EU) No 589/2014 Official Journal of the European Union. 2017.
Groh KJ, Muncke J. In vitro toxicity testing of food contact materials: state-of-the-art and future challenges. Compr Rev Food Sci Food Saf. 2017;16(5):1123–50.
Brack W, Ait-Aissa S, Burgess RM, Busch W, Creusot N, Di Paolo C, et al. Effect-directed analysis supporting monitoring of aquatic environments--an in-depth overview. Sci Total Environ. 2016;544:1073–118.
Rosenmai AK, Bengtstrom L, Taxvig C, Trier X, Petersen JH, Svingen T, et al. An effect-directed strategy for characterizing emerging chemicals in food contact materials made from paper and board. Food Chem Toxicol. 2017;106(Pt A):250–9.
Kunz PY, Simon E, Creusot N, Jayasinghe BS, Kienle C, Maletz S, et al. Effect-based tools for monitoring estrogenic mixtures: evaluation of five in vitro bioassays. Water Res. 2017;110:378–88.
Routledge EJ, Sumpter JP. Structural features of alkylphenolic chemicals associated with estrogenic activity. J Biol Chem. 1997;272(6):3280–8.
ISO. 19040-1. Water quality -- determination of the estrogenic potential of water and waste water -- part 1: Yeast estrogen screen (Saccharomyces cerevisiae). Geneva, Switzerland. 2018.
Escher BI, Neale PA, Villeneuve DL. The advantages of linear concentration-response curves for in vitro bioassays with environmental samples. Environ Toxicol Chem. 2018;37(9):2273–80.
Buchinger S, Spira D, Broder K, Schlusener M, Ternes T, Reifferscheid G. Direct coupling of thin-layer chromatography with a bioassay for the detection of estrogenic compounds: applications for effect-directed analysis. Anal Chem. 2013;85(15):7248–56.
Müller MB, Dausend C, Weins C, Frimmel FH. A new bioautographic screening method for the detection of estrogenic compounds. Chromatographia. 2004;60(3–4):207–11.
Spira D, Reifferscheid G, Buchinger S. Combination of high-performance thin-layer chromatography with a specific bioassay - a tool for effect-directed analysis. J Planar Chromatogr – Modern TLC. 2013;26(5):395–401.
Schönborn A, Grimmer A. Coupling sample preparation with effect-directed analysis of estrogenic activity - proposal for a new rapid screening concept for water samples. J Planar Chromatogr – Modern TLC. 2013;26(5):402–8.
Brack W. Effect-directed analysis: a promising tool for the identification of organic toxicants in complex mixtures? Anal Bianal Chem. 2003;377(3):397–407.
Schoenborn A, Schmid P, Bram S, Reifferscheid G, Ohlig M, Buchinger S. Unprecedented sensitivity of the planar yeast estrogen screen by using a spray-on technology. J Chromatogr A. 2017;1530:185–91.
Klingelhofer I, Morlock GE. Sharp-bounded zones link to the effect in planar chromatography-bioassay-mass spectrometry. J Chromatogr A. 2014;1360:288–95.
Moricz AM, Ott PG, Habe TT, Darcsi A, Boszormenyi A, Alberti A, et al. Effect-directed discovery of bioactive compounds followed by highly targeted characterization, isolation and identification, exemplarily shown for Solidago virgaurea. Anal Chem. 2016;88(16):8202–9.
Schick D, Schwack W. Logit-log evaluation of planar yeast estrogen screens. J Chromatogr A. 2017;1509:147–52.
Schick D, Schwack W. Planar yeast estrogen screen with resorufin-beta-d-galactopyranoside as substrate. J Chromatogr A. 2017;1497:155–63.
Könemann S, Kase R, Simon E, Swart K, Buchinger S, Schlüsener M, et al. Effect-based and chemical analytical methods to monitor estrogens under the European Water Framework Directive. TrAC Trends Anal Chem. 2018;102:225–35.
Beresford N, Routledge EJ, Harris CA, Sumpter JP. Issues arising when interpreting results from an in vitro assay for estrogenic activity. Toxicol Appl Pharmacol. 2000;162(1):22–33.
Muncke J. Exposure to endocrine disrupting compounds via the food chain: is packaging a relevant source? Sci Total Environ. 2009;407(16):4549–59.
Muncke J, Backhaus T, Geueke B, Maffini MV, Martin OV, Myers JP, et al. Scientific challenges in the risk assessment of food contact materials. Environ Health Perspect. 2017;125(9):095001.
Ogawa Y, Kawamura Y, Wakui C, Mutsuga M, Nishimura T, Tanamoto K. Estrogenic activities of chemicals related to food contact plastics and rubbers tested by the yeast two-hybrid assay. Food Addit Contam. 2006;23(4):422–30.
McDonnell DP, Nawaz Z, Densmore C, Weigel NL, Pham TA, Clark JH, et al. High level expression of biologically active estrogen receptor in Saccharomyces cerevisiae. J Steroid Biochem Mol Biol. 1991;39(3):291–7.
Routledge EJ, Sumpter JP. Estrogenic activity of surfactants and some of their degradation products assessed using a recombinant yeast screen. Environ Toxicol Chem. 1996;15(3):241–8.
Cimpoiu C, Hosu A, Hodisan S. Analysis of some steroids by thin-layer chromatography using optimum mobile phases. J Pharm Biomed Anal. 2006;41(2):633–7.
Briciu-Burghina C, Heery B, Regan F. Continuous fluorometric method for measuring beta-glucuronidase activity: comparative analysis of three fluorogenic substrates. Analyst. 2015;140(17):5953–64.
Baumgartner V, Schoenborn A, Grimmer A, Mainetti T, Pfändler I, Gude T. planar-YES: analysing food contact materials with an estrogen screen assay. International Life Sciences Institute, Barcelona. Poster Presentation. 2016.
Ritz C, Baty F, Streibig JC, Gerhard D. Dose-response analysis using R. PLoS One. 2015;10(12):e0146021.
Wagner M, Schlusener MP, Ternes TA, Oehlmann J. Identification of putative steroid receptor antagonists in bottled water: combining bioassays and high-resolution mass spectrometry. PLoS One. 2013;8(8):e72472.
Mertl J, Kirchnawy C, Osorio V, Grininger A, Richter A, Bergmair J, et al. Characterization of estrogen and androgen activity of food contact materials by different in vitro bioassays (YES, YAS, ERa and AR CALUX) and chromatographic analysis (GC-MS, HPLC-MS). PLoS One. 2014;9(7).
Harris CA, Henttu P, Parker MG, Sumpter JP. The estrogenic activity of phthalate esters in vitro. Environ Health Perspect. 1997;105(8):802–11.
Yu H, Caldwell DJ, Suri RP. In vitro estrogenic activity of representative endocrine disrupting chemicals mixtures at environmentally relevant concentrations. Chemosphere. 2019;215:396–403.
Simon C, Onghena M, Covaci A, Van Hoeck E, Van Loco J, Vandermarken T, et al. Screening of endocrine activity of compounds migrating from plastic baby bottles using a multi-receptor panel of in vitro bioassays. Toxicol in Vitro. 2016;37:121–33.
Fischer FC, Cirpka OA, Goss KU, Henneberger L, Escher BI. Application of experimental polystyrene partition constants and diffusion coefficients to predict the sorption of neutral organic chemicals to multiwell plates in in vivo and in vitro bioassays. Environ Sci Technol. 2018;52(22):13511–22.
Morlock GE, Klingelhofer I. Liquid chromatography-bioassay-mass spectrometry for profiling of physiologically active food. Anal Chem. 2014;86(16):8289–95.
Riegraf C, Reifferscheid G, Becker B, Belkin S, Hollert H, Feiler U, et al. Detection and quantification of photosystem II inhibitors using the freshwater alga Desmodesmus subspicatus in combination with high-performance thin-layer chromatography. Environ Sci Technol. 2019;53(22):13458–67.
Habe TT, Jamshidi-Aidji M, Macho J, Morlock GE. Direct bioautography hyphenated to direct analysis in real time mass spectrometry: chromatographic separation, bioassay and mass spectra, all in the same sample run. J Chromatogr. 2018;1568:188–96.
Escher BI, Aїt-Aїssa S, Behnisch PA, Brack W, Brion F, Brouwer A, et al. Effect-based trigger values for in vitro and in vivo bioassays performed on surface water extracts supporting the environmental quality standards (EQS) of the European Water Framework Directive. Sci Total Environ. 2018;628–629:748–65.
European Commission. Commission Regulation (EU) No 2018/213 on the use of bisphenol A in varnishes and coatings intended to come into contact with food and amending Regulation (EU) No 10/2011 as regards the use of that substance in plastic food contact materials. Official Journal of the European Union. 2018.
Acknowledgments
The implementation of this work was facilitated by Inge Werner (Swiss Centre for Applied Ecotoxicology) and Juliane Hollender (Department of Environmental Chemistry, Eawag). The analytical committee of Eawag and the Swiss Federal Office for the Environment supported purchase of equipment. Gregor McCombie (Cantonal Laboratory Zurich) and Vera Baumgartner (Swiss Quality Testing Services) supplied FCMs. Ali Kizgin (Swiss Centre for Applied Ecotoxicology) provided E2 results from L-YES for CPRG and MUG comparison. Sina Hasler helped with laboratory operations. Bernd Spangenberg (University of Offenburg), Sebastian Buchinger (The German Federal Institute of Hydrology), Stefan Weiss, and Wolfgang Schultz (both at Langenau State Water Supply, Germany) provided helpful advice regarding HPTLC and bioassays. Jane Muncke (Food Packaging Forum) provided resources regarding FCM. Tamara Mainetti (Zurich University for Applied Sciences) performed preliminary FCM and P-YES work.
Funding
Food Safety and Veterinary Office of Switzerland project number 4.17.05. The analytical committee of Eawag and the Swiss Federal Office for the Environment supported purchase of equipment.
Author information
Authors and Affiliations
Contributions
A. Bergmann designed and performed experiments, analyzed and interpreted the data, and drafted the manuscript. E. Simon designed experiments, interpreted data, and revised the manuscript. A. Schifferli collected and analyzed data for the L-YES and reviewed the manuscript. A. Schönborn conceived of the project, interpreted data, and revised the manuscript. E. Vermeirssen conceived of the project, designed experiments, interpreted data, and revised the manuscript.
Corresponding author
Ethics declarations
Conflict of interest
A. Schönborn is co-founder of a university spin-off company offering services related to this research. A. Bergmann, E. Simon, A. Schifferli, and E. Vermeirssen declare that they have no conflict of interest.
Code availability
R code used in the current study is available from the corresponding author on request, and will be available at https://opendata.eawag.ch/.
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
ESM 1
(PDF 967 kb)
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Bergmann, A., Simon, E., Schifferli, A. et al. Estrogenic activity of food contact materials—evaluation of 20 chemicals using a yeast estrogen screen on HPTLC or 96-well plates. Anal Bioanal Chem 412, 4527–4536 (2020). https://doi.org/10.1007/s00216-020-02701-w
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00216-020-02701-w