Abstract
The extreme temperatures in weld zone during friction stir welding (FSW) directly affect the welding quality of the joints. Therefore, characterization of the maximum and minimum temperatures in weld zone is essential to ensure welding quality. However, direct measurement or prediction based on simulation is difficult due to the occlusion of the tool shoulder and the severe plastic deformation of the weldment under thermo-mechanical effects during the welding process. To solve the problem, this paper presents a method for prediction of extreme temperatures in weld zone based on infrared thermography. Firstly, a 3D temperature field simulation model of FSW is established based on DEFORM, and the experiments are conducted to verify the validity of the simulation model. The data sets of temperature of surface feature points and the maximum and minimum temperatures in weld zone are obtained. Then, support vector regression (SVR) is used to establish a temperature prediction model, which represents the correlation between the temperature of surface feature point and the extreme temperatures in weld zone. In practical FSW process, an infrared thermal imager is used to measure the temperature of the surface feature point. Combined with the built temperature prediction model, the prediction of the extreme temperatures in the weld zone is achieved. The research provides references for temperature-based process control of FSW.
Similar content being viewed by others
Data availability
All data generated or analysed during this study are included in this manuscript.
Code availability
The code is available on request.
References
Khan NZ, Siddiquee AN, Khan ZA, Mukhopadhyay AK (2017) Mechanical and microstructural behavior of friction stir welded similar and dissimilar sheets of AA2219 and AA7475 aluminium alloys. J Alloys Compd 695:2902–2908. https://doi.org/10.1016/j.jallcom.2016.11.389
Rouhi S, Mostafapour A, Ashjari M (2016) Effects of welding environment on microstructure and mechanical properties of friction stir welded AZ91C magnesium alloy joints. Sci Technol Weld Joining 21(1):41–47. https://doi.org/10.1179/1362171815Y.0000000058
Lu X, Zhou Y, Sun S, Luan Y, Qiao J, Qian J (2022) Temperature field measurement and analyses of friction stir welding 18mm thick 2219 aluminum alloy. Exp Techniques 47(3):579–590. https://doi.org/10.1007/s40799-022-00556-7
Li JP, Cao FJ, Shen YF (2020) Effect of welding parameters on friction stir welded Ti-6Al-4V joints: temperature, microstructure and mechanical properties. Metals-Basel 10(7):940. https://doi.org/10.3390/met10070940
Ambrosio D, Wagner V, Garnier C, Jacquin D, Tongne A, Fazzini M, Cahuc O, Dessein G (2020) Influence of welding parameters on the microstructure, thermal fields and defect formation in AA7075-T6 friction stir welds. Weld World 64(5):773–784. https://doi.org/10.1007/s40194-020-00869-4
Ma ZS, Hou XY, Chen SR (2018) Effects of sizes of stirring head shoulder on performance of 2219 aluminum alloy friction stir welding joint. Hot Working Technol 47(5):194–198+202
Ajri A, Rohatgi N, Shin YC (2020) Analysis of defect formation mechanisms and their effects on weld strength during friction stir welding of Al 6061–T6 via experiments and finite element modeling. Int J Adv Manuf Technol 107(11–12):4621–4635. https://doi.org/10.1007/s00170-020-05353-3
Bocchi S, D’Urso G, Giardini C (2021) The effect of heat generated on mechanical properties of friction stir welded aluminum alloys. Int J Adv Manuf Technol 112(5):1513–1528. https://doi.org/10.1007/s00170-020-06462-9
Zhai M, Wu CS, Su H (2020) Influence of tool tilt angle on heat transfer and material flow in friction stir welding. J Manuf Process 59:98–112. https://doi.org/10.1016/j.jmapro.2020.09.038
Magalhaes A, De Backer J, Martin J, Bolmsjo G (2019) In-situ temperature measurement in friction stir welding of thick section aluminium alloys. J Manuf Process 39:12–17. https://doi.org/10.1016/j.jmapro.2019.02.001
Magalhaes A, De Backer J, Bolmsjo G (2019) Thermal dissipation effect on temperature-controlled friction stir welding. Soldagem Insp 24:e2428. https://doi.org/10.1590/0104-9224/SI24.28
Hynes NRJ, Jebaraj DJJ, Selvaraj M, Ali MA, Raza MH, Pruncu CI, Velu PS, Vignesh NJ (2022) Thermal behavior analysis and mechanical characterization of friction stud welded AISI 304/AA6063 joints. J Braz Soc Mech Sci 44(4):114. https://doi.org/10.1007/s40430-022-03412-2
Pandian V, Kannan S (2020) Numerical prediction and experimental investigation of aerospace-grade dissimilar aluminium alloy by friction stir welding. J Manuf Process 54:99–108. https://doi.org/10.1016/j.jmapro.2020.03.001
Salloomi KN (2019) Fully coupled thermomechanical simulation of friction stir welding of aluminum 6061–T6 alloy T-joint. J Manuf Process 45:746–754. https://doi.org/10.1016/j.jmapro.2019.06.030
Sibalic N, Vukcevic M (2019) Numerical simulation for FSW process at welding aluminium alloy AA6082-T6. Metals-Basel 9(7):747. https://doi.org/10.3390/met9070747
Raju S, Jagadish RC, Aadapa SK, Yanda S (2022) Predication of temperature distribution and strain during FSW of dissimilar aluminum alloys using deform 3D. Mater Today-Proc 59:1760–1767. https://doi.org/10.1016/j.matpr.2022.04.371
Wan XY, Hu ZL, Pang Q, Zhan BY (2019) Thermal model and peak temperature in high-travel velocity friction stir welding of aluminum alloy. Rare Metal Mat Eng 48(6):1990–1995
Zhang YC, Cui Y, Fu XB, Sun SX (2019) Temperature measurements using an infrared camera in the core area of a stirring tool. Insight 61(8):440–447. https://doi.org/10.1784/insi.2019.61.8.440
Zhang ZQ, Jiang ZL, Wei QY (2017) Dynamic mechanical properties and constitutive equations of 2219 aluminum alloy. J Mater Eng 45(10):47–51. https://doi.org/10.11868/j.issn.1001-4381.2016.000859
Tutunchilar S, Haghpanahi M, Givi MKB, Asadi P, Bahemmat P (2012) Simulation of material flow in friction stir processing of a cast Al–Si alloy. Mater Design 40:415–426. https://doi.org/10.1016/j.matdes.2012.04.001
Xu WF, Liu JH, Zhu HQ (2010) Numerical simulation of thermal field of friction stir welded 2219 aluminum alloy thick plate. Trans China Weld Inst 124(1):5–13
Cortes C, Vapnik V (1995) Support-Vector Networks. Mach Learn 20(3):273–297. https://doi.org/10.1007/BF00994018
Funding
The research was supported by the National Key Research and Development Program of China (Grant No. 2019YFA0709003) and Natural Science Foundation of Liaoning Province of China(2023-MS-101).
Author information
Authors and Affiliations
Contributions
Xiaohong Lu: conceptualization, supervision, methodology, funding acquisition, project administration.
Guochuan Sui: conceptualization, methodology, software, validation, writing—original draft, investigation, writing—review and editing.
Weisong Zhang: formal analysis, data curation.
Shixuan Sun: investigation, formal analysis.
Steven Y. Liang: resources.
Corresponding author
Ethics declarations
Ethics approval
Not applicable.
Consent to participate
Not applicable.
Consent for publication
The authors consent that the work entitled as Prediction of extreme temperatures in weld zone of friction stir welding for possible publication in International Journal of Advanced Manufacturing Technology.
Competing interests
The authors declare no competing interests.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Lu, X., Sui, G., Zhang, W. et al. Prediction of extreme temperatures in weld zone of friction stir welding. Int J Adv Manuf Technol 131, 505–514 (2024). https://doi.org/10.1007/s00170-024-13102-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-024-13102-z