Abstract
The relative vibration displacement between the tool tip and workpiece will inevitably affect the machined surface topography during the machining process of the ultra-precision fly cutting machine tool. The dynamic performance of the rotational component consisting of the spindle, the fly cutting head, and tool holders needs to be comprehensively investigated because of its significant influences on the waviness generation on the workpiece surface. In this paper, the finite element method is adopted to establish the dynamics model of the rotational component, and then the dynamics analysis proves that the deformation of the fly cutting head and tool holders significantly affects the tool tip displacement, which is validated by a modal test and a machining test. Subsequently, three optimization schemes of the fly cutting head and three optimization schemes of the tool holder are proposed and analyzed. According to the analysis and comparison results of the dynamics response, the optimization scheme of the fly cutting head 2 and the tool holder 3 is selected as the final optimization scheme, which effectively decreases the tool tip displacement by 16.97%. The simulation results of the optimization scheme are validated by the modal test.
Similar content being viewed by others
Data availability
Not applicable.
Code availability
Not applicable.
References
Lucca DA, Klopfstein MJ, Riemer O (2020) Ultra-Precision Machining: Cutting With Diamond Tools. ASME J Manuf Sci Eng 142(11):110817. https://doi.org/10.1115/1.4048194
Yuan ZJ, Wang XK (2016) The Technology of Precision Machining and Ultra-Precision Machining, 3rd edn. China Machine Press, Beijing (in Chinese)
Yuan JL, Lyu BH, Hang W, Deng QF (2017) Review on the progress of ultra-precision machining technologies. Front Mech Eng 12(2):158–180. https://doi.org/10.1007/s11465-017-0455-9
Kosc TZ, Huang H, Kessler TJ, Demos SG (2022) Angular dependence of the transverse Raman scattering in KDP and DKDP in geometries suitable for beam polarization control. Opt Express 30(8):12918–12928. https://doi.org/10.1364/OE.448388
Zhang Y, Hou N, Zhang LC (2020) Effect of ultra-precision fly-cutting on the surface integrity of potassium dihydrogen phosphate crystals. Opt Mater Express 10(4):971–980. https://doi.org/10.1364/OME.390276
Chen WQ, Lu LH, Liang YC, Sun YZ, Chen GD, An CH (2015) Flatness improving method of KDP crystal in ICF system and its implementation in machine tool design. Proc IMechE Part E: J Process Mechanical Engineering 229(4):327–332. https://doi.org/10.1177/0954408914528323
Xia H, Han CQ, Xiao H (2014) Research on single-point diamond fly-cutting machining of large size thin aluminum plates. Modular Mach Tool Automatic Manuf Technol 6: 106–108 (in Chinese) https://doi.org/10.13462/j.cnki.mmtamt.2014.06.029
Wei W, Li JS, Chen Y, Huang XJ (2020) Analysis of characteristics of arc shape caused by intermittent cutting force and dynamic vibration in ultra-precision cutting processes. Proc IMechE Part B: J Engineering Manufacture 234(14):1742–1751. https://doi.org/10.1177/0954405420928738
Wang BR, Ji F, Zhao WY, Chen DS (2011) Development of DFC-600A ultra-precision single-point diamond fly cutting machine tool. Opto-Electronic Eng 38(12): 81–84 (in Chinese) https://doi.org/10.3969/j.issn.1003-501X.2011.12.015
Hatefi S, Abou-El-Hossein K (2020) Review of single-point diamond turning process in terms of ultra-precision optical surface roughness. Int J Adv Manuf Technol 106:2167–2187. https://doi.org/10.1007/s00170-019-04700-3
Zhang SJ, To S, Zhu ZW, Zhang GQ (2016) A review of fly cutting applied to surface generation in ultra-precision machining. Int J Mach Tools Manuf 103:13–27. https://doi.org/10.1016/j.ijmachtools.2016.01.001
Zhang SJ, To S, Zhang GQ, Zhu ZW (2015) A review of machine-tool vibration and its influence upon surface generation in ultra-precision machining. Int J Mach Tools Manuf 91:34–42. https://doi.org/10.1016/j.ijmachtools.2015.01.005
Liang YC, Chen WQ, Sun YZ, Chen GD, Wang T, Sun Y (2012) Dynamic design approach of an ultra-precision machine tool used for optical parts machining. Proc IMechE Part B: J Engineering Manufacture 226:1930–1936. https://doi.org/10.1177/0954405412458998
Chen WQ, Sun YZ, An CH, Su H, Yang K, Zhang Q (2015) Modelling and simulation of the interaction of manufacturing proces and machine tool structure in flycutting maching. Proc IMechE Part C: J Mechanical Engineering Science 229(15):2730–2736. https://doi.org/10.1177/0954406214563962
An CH, Zhang Y, Xu Q, Zhang FH, Zhang JF, Zhang LJ, Wang JH (2010) Modeling of dynamic characteristic of the aerostatic bearing spindle in an ultra-precision fly cutting machine. Int J Mach Tools Manuf 50:374–385. https://doi.org/10.1016/j.ijmachtools.2009.11.003
Deng CY, An CH, Wei B, Miao JG (2019) Investigation on the influence of aerostatic pressure upon surface generation in flycutting. Proc IMechE Part B: J Eng Manuf 233(4):1136–1143. https://doi.org/10.1177/0954405418780164
Rui XT, Zhang JS, Wang X, Rong B, He B, Jin Z (2022) Multibody system transfer matrix method: The past, the present, and the future. Int J Mech Syst Dyn 2:3–26. https://doi.org/10.1002/msd2.12037
Ding YY, Rui XT, Chen GL, Liu XB, Zeng XY (2018) Study on the Natural Vibration Characteristics of Single-Point Diamond Fly Cutting Machine Tool Based on Transfer Matrix Method for Multibody Systems. C. ASME 2018 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference, Quebec City, Canada.https://doi.org/10.1115/DETC2018-85545
Ding JG, Chang Y, Chen P, Zhuang H, Ding YY, Lu HJ, Chen YH (2020) Dynamic modeling of ultra-precision fly cutting machine tool and the effect of ambient vibration on its tool tip response. Int J Extrem Manuf 2:025301. https://doi.org/10.1088/2631-7990/ab7b59
Lu HJ, Ding YY, Chang Y, Chen GL, Rui XT (2020) Dynamics modelling and simulating of ultra-precision fly-cutting machine tool. Int J Precis Eng Manuf 21(2):189–202. https://doi.org/10.1007/s12541-019-00239-1
Lu HJ, Rui XT, Ding YY, Chang Y, Chen YH, Ding JG, Zhang XP (2022) A hybrid numerical method for vibration analysis of linear multibody systems with flexible components. Appl Math Model 101:748–771. https://doi.org/10.1016/j.apm.2021.09.015
Lu HJ, Rui XT, Ma ZY, Ding YY, Chen YH, Chang Y, Zhang XP (2022) Hybrid multibody system method for the dynamic analysis of an ultra-precision fly-cutting machine tool. Int J Mech Syst Dyn 2(3):290–307. https://doi.org/10.1002/msd2.12051
Ma JL, Yang W, An CH, Tang HY, Luo XY (2021) CGHMM basd fault identification for single point diamond flycutting machines. Optiks 239:166860. https://doi.org/10.1016/j.ijleo.2021.166860
Chen DJ, Li SP, Zhang X, Fan JL (2022) Relationship between dynamic characteristics of air film of aerostatic spindle and mid-frequency of surface topography. Adv Manuf 10:428–442. https://doi.org/10.1007/s40436-022-00391-4
Miao JG, Yu DP, An CH, Ye FF, Yao J (2017) Investigation on the generation of the medium-frequency waviness error in flycutting based on 3D surface topography. Int J Adv Manuf Technol 90:667–675. https://doi.org/10.1007/s00170-016-9404-8
Zhang FH, Wang SF, An CH, Wang J, Xu Q (2017) Full-band error control and crack-free surface fabrication techniques for ultra-precision fly cutting of large-aperture KDP crystals. Front Mech Eng 12:193–202. https://doi.org/10.1007/s11465-017-0448-8
Gao Q, Zhao H, Lu LH, Chen WQ, Zhang FH (2020) Investigation on the formation mechanism and controlling method of machined surface topography of ultra-precision flycutting machining. Int J Adv Manuf Technol 106:3311–3320. https://doi.org/10.1007/s00170-019-04869-7
Wei RC, An CH, Wang ZZ, Xu Q, Lei XY, Zhang JF (2020) Dynamic performance analysis and quantitative evaluation for ultraprecision aerostatic spindle. Proc IMechE Part B: J Eng Manuf 234(1–2):218–228. https://doi.org/10.1177/0954405419855239
Chang Y, Ding JG, He ZF, Shehzad A, Ding YY, Lu HJ, Zhuang H, Chen P, Zhang Y, Zhang XX, Chen YH (2020) Effect of joint interfacial contact stiffness on structural dynamics of ultra-precision machine tool. Int J Mach Tools Manuf 158:103609. https://doi.org/10.1016/j.ijmachtools.2020.103609
An CH, Wei RC, Wang ZZ, Xu Q, Lei XY, Zhang JF (2021) Investigation on dynamic performance of ultra-precision flycutting machine tool based on virtual material method. Proc IMechE Part B: J Eng Manuf 235(9). https://doi.org/10.1177/0954405421990134
Funding
This work was supported by the Science Challenge Project (Grant No. JDZZ2016006-0102), National Natural Science Foundation of China (Grant No. 11902158), National Natural Science Foundation of China (Grant No. 52105129) and Natural Science Foundation of Jiangsu Province (Grant No.BK20190438).
Author information
Authors and Affiliations
Contributions
All authors contributed to the study conception and design. Material preparation, data collection and analysis were performed by Yuanyuan Ding and Yu Chang. The first draft of the manuscript was written by Yuanyuan Ding, and all authors commented on previous versions of the manuscript. Supervisions and revisions were performed by Xiaoting Rui. Experiments were performed by Hanjing Lu, Yiheng Chen, Jianguo Ding, Adeel Shehzad, Gangli Chen and Junjie Gu. All authors read and approved the final manuscript.
Corresponding author
Ethics declarations
Ethical approval
Not applicable.
Consent to participate
Not applicable.
Consent to publish
Depending on the ownership of the journal and its policies, my co-authors and I either grant the Publisher an exclusive license to publish the article or will be asked to transfer copyright of the article to the Publisher.
Conflict of interest
The authors have no relevant financial or non-financial interests to disclose.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Ding, Y., Rui, X., Chang, Y. et al. Optimal design of the dynamic performance of the ultra-precision fly cutting machine tool. Int J Adv Manuf Technol 124, 567–585 (2023). https://doi.org/10.1007/s00170-022-10502-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-022-10502-x