Abstract
The thermal effects of the “keyhole” full penetration welding mode, which is characteristic of high-power CO2 laser, are simulated introducing a multipoint-line thermal source model based on heat conduction, parameterized by the distribution of the laser beam power, and the setting of the source system layout, and to be fitted on experimentally detected cross sections of the heat-affected or fusion zones of the weld. The proposed model allows to express the thermal field according to the moving reference system fixed on the overall heat source, and to analyze the temperature profiles that develop in some detection points fixed on the workpiece, as time varies during the welding process. By this way, it can be useful in evaluating the thermal effects that result from the variation of the main welding parameters (beam power, welding speed, plate thickness), with the aim of simplifying the selection of the optimal process conditions. As an application, reference is made to a cross section of a joint between plates of AISI 304 L austenitic steel. The fitting procedure allows to set the power distribution and layout parameters of the most suitable source combination (obtained by superposition of a line and two point sources). The value of the absorption coefficient also is assumed as fitting variable, so to overcome the complex problem of evaluating the beam power actually absorbed by the material on keyhole mode welding. Finally, the fitted model is applied to carry out a detailed thermal field analysis in the welded plates.
Similar content being viewed by others
Data availability
The raw data and processing aids required to reproduce the findings cannot be shared at this time as they form the basis for an ongoing study.
References
Syahroni N, Hidayat MIP (2012) 3D finite element simulation of T-joint fillet weld: effect of various welding sequences on the residual stresses and distortions. In: Andriychuk M (ed) Numerical Simulation - From Theory to Industry, edn., IntechOpen, chap. 24, pp 583–606. https://www.intechopen.com/books/numerical-simulation-from-theory-to-industry/3d-finite-element-simulation-of-t-joint-fillet-weld-effect-of-various-welding-sequences-on-the-resid
Islam M, Buijk A, Rais-Rohani M, Motoyama K (2014) Simulation-based numerical optimization of arc welding process for reduced distortion in welded structures. Finite Elem Anal Des 84:54–64
Sajek A (2019) Application of FEM simulation method in area of the dynamics of cooling AHSS steel with a complex hybrid welding process. Weld World 63:1065–1073
Nezamdost MR, Nekouie Esfahani MR, Hashemi SH, Mirbozorgi SA (2016) Investigation of temperature and residual stresses field of submerged arc welding by finite element method and experiments. Int J Adv Manuf Technol 87:615–624
Tomashchuk I, Bendaoud I, Sallamand P, Cicala E, Lafaye S, Almuneau M (2016) Multiphysical modelling of keyhole formation during dissimilar laser welding. Proceedings of the 2016 COMSOL Conference, October 12-14, Munich. https://www.comsol.it/paper/download/361001/tomashchuk_paper.pdf
Lankalapalli KN, Tu JF, Leong KH, Gartner M (1999) Laser weld penetration estimation using temperature measurements. ASME J Manuf Sci Eng 121:179–188
Anca A, Cardona A, Risso J, Fachinotti VD (2011) Finite element modeling of welding processes. Appl Math Model 35:688–707
Rosenthal D (1946) The theory of moving sources of heat and its application to metal treatments. Trans ASME 68:849–866
Carslaw HS, Jaeger JC (1959) Conduction of heat in solids. Oxford University Press, London
Ashby MF, Easterling KE (1984) The transformation hardening of steel surfaces by laser beam. Acta Metall 32:1935–1948
Mackwood AP, Crafer RC (2005) Thermal modelling of laser welding and related processes: a literature review. Opt Laser Technol 37:99–115
Missori S, Costanza G, Sili A, Tata ME (2015) Metallurgical modifications and residual stress in welded steel with average carbon content. Weld Int 29(2):124–130
Missori S, Sili A (2018) Prediction of weld metal microstructure in laser beam weld metal clad steel. Metallurgist 62:84–92
Svenungsson J, Choquet I, Kaplan AFH (2015) Laser welding process: a review of keyhole welding modelling. Phys Procedia 78:182–191
Volpp J, Vollertsen F (2016) Keyhole stability during laser welding-part I: modeling and evaluation. Prod Eng Res Dev 10:443–457
Steen WM, Dowden J, Davis M, Kapadia P (1988) A point and line source model of laser keyhole welding. J Phys D Appl Phys 21:1255–1260
Akhter R, Davis M, Dowden J, Kapadia P, Ley M, Steen WM (1989) A method for calculating the fused zone profile of laser keyhole welds. J Phys D Appl Phys 21:23–28
Dowden J, Kapadia P (1998) Point and line sources: models of power absorption in the theory of welding. Proceedings of ICALEO ’98 Laser Materials Processing Conference, November 16-19, Orlando, Florida. https://lia.scitation.org/doi/abs/10.2351/1.5059194
Dowden JM (2001) The mathematics of thermal modelling: an introduction to the theory of laser material processing. Chapman & Hall/CRC, Boca Raton
Metzbower EA (1990) Laser beam welding: thermal profiles and HAZ hardness. Weld J 7:272 s–278 s
Kaplan A (1994) A model of deep penetration laser welding based on calculation of the keyhole profile. J Phys D Appl Phys 27:1805–1814
Dowden JM, Ducharme R, Kapadia PD (1998) Time dependent line and point sources: a simple model for time-dependent welding processes. Lasers Eng 7:215–228
Postacioglu N, Kapadia P, Dowden J (1993) A mathematical model of heat conduction in a prolate spheroidal coordinate system with applications to the theory of welding. J Phys D Appl Phys 26:563–573
Van Elsen M, Baelmans M, Mercelis P, Kruth J-P (2007) Solutions for modelling moving heat sources in a semi-infinite medium and applications to laser material processing. Int J Heat Mass Transf 50:4872–4882
Franco A, Romoli L, Musacchio A (2014) Modelling for predicting seam geometry in laser beam welding of stainless steel International. J Therm Sci 79:194–205
Mościcki T, Hoffman J, Szymański Z (2006) Modelling of plasma plume induced during laser welding. J Phys D Appl Phys 39:685–692
Zhou J, Tsai HL, Wang PC (2006) Transport phenomena and keyhole dynamics during pulsed laser welding. J Heat Transf 128:680–690
Missori S, Murdolo F, Sili A (2004) Single-pass laser beam welding of clad steel plate. Weld J 83:65 s–71 s
Mills KC (2002) Recommended values of thermophysical properties for selected commercial alloys. Woodhead Publishing, Cambridge
Hoffman J, Szymanski Z (2002) Absorption of the laser beam during welding with CO2 laser. Opt Appl 32:129–145
Ricciardi G, Cantello M (1994) Laser material interaction: absorption coefficient in welding and surface treatment. Ann CIRP 43:171–175
Rai R, Elmer JW, Palmer TA, DebRoy T (2007) Heat transfer and fluid flow during keyhole mode laser welding of tantalum, Ti-6Al-4 V, 304 L stainless steel and vanadium. J Phys D Appl Phys 40:5753–5766
Myiamoto I, Maruo H, Arata Y (1986) Beam absorption mechanism in laser welding. Proceedings of Symposium on Laser Processing: Fundamentals, Applications, and Systems Engineering, November 12th Quebec City, Canada, vol 668, pp 11–18. https://www.spiedigitallibrary.org/conference-proceedings-of-spie/0668/1/Beam-Absorption-Mechanism-In-Laser-Welding/10.1117/12.938878.short
Weman K (2003) Welding processes handbook, vol chap. 14. Woodhead Publishing Ltd, Cambridge, p 143
Khan MMA, Romoli L, Ishak R, Fiaschi M, Dini G, De Sanctis M (2012) Experimental investigation on seam geometry, microstructure evolution and microhardness profile of laser welded martensitic stainless steel. Opt Laser Technol 44:1611–1619
Author information
Authors and Affiliations
Contributions
Fabio Giudice: conceptualization, methodology, data curation, writing—original draft, validation, formal analysis, visualization, and supervision.
Severino Missori: conceptualization, investigation, resources, data curation, and visualization.
Andrea Sili: conceptualization, methodology, data curation, writing—original draft, formal analysis, investigation, visualization, and supervision.
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no conflict of interest.
Ethics approval
Not applicable.
Consent to participate
Not applicable.
Consent for publication
Not applicable.
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Giudice, F., Missori, S. & Sili, A. Parameterized multipoint-line analytical modeling of a mobile heat source for thermal field prediction in laser beam welding. Int J Adv Manuf Technol 112, 1339–1358 (2021). https://doi.org/10.1007/s00170-020-06479-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-020-06479-0