Abstract
Electron beam additive manufacturing (EBAM) is an additive manufacturing (AM) technique increasingly used by many industrial sectors, including medical and aerospace industries. The application of this technology is still, however, challenged by many technical barriers. One of the major issues is the lack of process monitoring and control system to monitor process repeatability and component quality reproducibility. Various techniques, mainly involving infrared (IR) and optical cameras, have been employed in previous attempts to study the quality of the EBAM process. However, all attempts lack the flexibility to zoom-in and focus on multiple regions of the processing area. In this paper, a digital electronic imaging system prototype and a piece of macroscopic process quality analysis software are presented. The prototype aims to provide flexibility in magnifications and the selection of fields of view (FOV). The software aims to monitor the EBAM process on a layer-by-layer basis. Digital electronic images were generated by detecting both secondary electrons (SE) and backscattered electrons (BSE) originating from interactions between the machine electron beam and the processing area using specially designed hardware. Prototype capability experiments, software verification and demonstration were conducted at room temperature on the top layer of an EBAM test build. Digital images of different magnifications and FOVs were generated. The upper range of the magnification achieved in the experiments was 95 and the demonstration verified the potential ability of the software to be applied in process monitoring. It is believed that the prototype and software have significant potential to be used for in-process EBAM monitoring in many manufacturing sectors. This study is thought to be the necessary precursor for future work which will establish whether the concept is suited to working under in-process EBAM operating conditions.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Gibson I, Rosen DW, Stucker B (2010) Additive manufacturing technologies. Springer, New York, pp 126–130
Gong X, Anderson T, Chou K (2014) Review on powder-based electron beam additive manufacturing technology. Manufacturing Review 1:2. https://doi.org/10.1051/mfreview/2014001
Harrysson OLA, Cansizoglu O, Marcellin-Little DJ, Cormier DR, West HA (2008) Direct metal fabrication of titanium implants with tailored materials and mechanical properties using electron beam melting technology. Mater Sci Eng C 28(3):366–373, ISSN 0928-4931. https://doi.org/10.1016/j.msec.2007.04.022
Baudana G, Biamino S, Ugues D, Lombardi M, Fino P, Pavese M, Badini C (2016) Titanium aluminides for aerospace and automotive applications processed by electron beam melting: contribution of Politecnico di Torino. Metal Powder Report 71(3):193–199, ISSN 0026-0657. https://doi.org/10.1016/j.mprp.2016.02.058
Jarow JP, Baxley JH (2015) Medical devices: US medical device regulation. Urologic Oncology: Seminars and Original Investigations 33(3):128–132, ISSN 1078-1439. https://doi.org/10.1016/j.urolonc.2014.10.004
Portolés L, Jordá O, Jordá L, Uriondo A, Esperon-Miguez M, Perinpanayagam S (2016) A qualification procedure to manufacture and repair aerospace parts with electron beam melting. J Manuf Syst 41:65–75, ISSN 0278-6125. https://doi.org/10.1016/j.jmsy.2016.07.002
Mani M, Lane B, Donmez A, Feng S, Moylan S, Fesperman R (2015) NISTIR 8036. Measurement science needs for real-time control of additive manufacturing powder bed fusion processes. https://doi.org/10.6028/NIST.IR.8036
Raplee J, Plotkowski A, Kirka MM, Dinwiddie R, Okello A, Dehoff RR, Babu SS (2017) Thermographic microstructure monitoring in electron beam additive manufacturing. Sci Rep 7:43554. https://doi.org/10.1038/srep43554
Cordero PM, Mireles J, Ridwan S, Wicker RB (2017) Evaluation of monitoring methods for electron beam melting powder bed fusion additive manufacturing technology. Progress in Additive Manufacturing 2(1-2):1–10. https://doi.org/10.1007/s40964-016-0015-6
Rodriguez E, Medina F, Espalin D, Terrazas C, Muse D, Henry C, MacDonald E, Wicker R (2012) Integration of a thermal imaging feedback control system in electron beam melting. Proceedings from the Solid Freeform Fabrication Symposium, pp 945–961
Price S,Cooper K, Chou K (2012) Evaluations of temperature measurmnets by near-infrared thermography in powder-based electron-beam additive manufacturing. Proceedings from the Solid Freeform Fabrication Symposium, pp 761–773
Price S, Lydon J, Cooper K, Chao K (2013) Experimental temperature analysis of powder-based electron beam additive manufacturing. Proceedings from the Solid Freeform Fabrication Symposium, pp 162–173
Zalameda JN, Burke ER, Hafley RA, Taminger KMB, Domack CS, Brewer A, Martin RE (2013) Thermal imaging for assessment of electron-beam freeform fabrication additive manufacturing deposits. Proceeding of SPIE, Volume 8705, Thermosense: Thermal Infrared Applications XXXV, 87050M. https://doi.org/10.1117/12.2018233
Scharowsky T, Bauereiß A, Singer RF, Körner C (2012) Observation and numerical simulation of melt pool dynamic and beam powder interaction during selective electron beam melting. Proceedings from the Solid Freeform Fabrication Symposium, Austin, pp 815–820
Ridwan S, Mireles J, Gayton SM, Espalin D, Wicker RB (2014) Automatic layerwise acquisition of thermal and geometric data of the electron beam melting process using infrared thermography. Proceedings from the Solid Freeform Fabrication Symposium, pp 343–352
Mireles J, Ridwan S, Motron PA, Hinojos A, Wicker RB (2015) Analysis and correction of defects within parts fabricated using powder bed fusion technology. Surface Topography: Metrology and Properties 3(3). https://doi.org/10.1088/2051-672X/3/3/034002
Dinwiddie RB, Dehoff RR, Lloyd PD, Lowe LE, Ulrich JUB (2013) Thermographic in-situ process monitoring of the electron-beam melting technology used in additive manufacturing. Proceeding of SPIE, Thermosense: Thermal Infrared Applications XXXV, 87050K. https://doi.org/10.1117/12.2018412
Schwerdtfeger J, Singer RF, Körner C (2012) In situ flaw detection by IR-imaging during electron beam melting. Rapid Prototyp J 18(4):259–263. https://doi.org/10.1108/13552541211231572
Mireles J, Terrazas C, Gaytan SM, Roberson DA, Wicker RB (2015) Closed-loop automatic feedback control in electron beam melting. Int J Adv Manuf Technol 78:1193–1199. https://doi.org/10.1007/s00170-014-6708-4
Mireles J, Terrazas C, Medina F, Wicker R (2013) Automatic feedback control in electron beam melting using infrared thermography. Proceedings from the Solid Freeform Fabrication Symposium, Austin, pp 708–717
Hobbs N (2017) Arcam EBAM, SE region aerospace supplier and advanced manufacturing summit presentation
National Institute of Standards and Technology U.S. Depeartment of Commerce (2013) Measurement science roadmap for metal-based additive manufacturing. Workshop Summary Report, pp 71
Tapia G, Elwany A (2014) A review on process monitoring and control in metal-based additive manufacturing. ASME Journal of Manufacturing Science and Engineering 136(6):060801-060801-10. https://doi.org/10.1115/1.4028540
Everton SK, Hirsch M, Stravroulakis P, Leach RK, Clare AT (2016) Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing. Mater Des 95:431–445, ISSN 0264-1275. https://doi.org/10.1016/j.matdes.2016.01.099
Grasso M, Colosimo BM (2017) Process defects and in situ monitoring methods in metal powder bed fusion: a review. Meas Sci Technol 28(4):044005. https://doi.org/10.1088/1361-6501/aa5c4f
Everton S (2015) In-process metrology for AM, Presentation
Oltean SE (2018) Strategies for monitoring and control with seam tracking in electron beam welding, Proceeding from 11th International Conference Interdisciplinary in Engineering, INTER-ENG 2017, Procedia Manufacturing 22(2018):605–612
Trushnikov D, Krotova E, Koleva E (2016) Use of a secondary current sensor in plasma during electron-beam welding with Forus scanning for process control. Journal of Sensors 2016:5302681. https://doi.org/10.1155/2016/5302681
Oltean SE, Abrudean M (2008) Advanced control of the electron beam welding. Journal of Control Engineering and Applied Informatics 10(1):40–48
Trushnikov D, Belenkiy V, Shchavlev V, Piskunov A, Abdullin A, Mladenov G (2012) Plasma charge current for controlling and monitoring electron beam welding with beam oscillation. Sensors 12(12):17433–17445. https://doi.org/10.3390/s121217433
Koleva EG, Mladenov GM, Trushnikov D, Belenkiy V (2014) Signal emitted from plasma during electron-beam welding with deflection oscillations of the beam. J Mater Process Technol 214(9):1812–1819. https://doi.org/10.1016/j.jmatprotec.2014.03.031
Trushnikov D, Belenkiy V, Mladenov G, Portnov N (2012) Secondary-emission signal for weld formation monitoring and control in electron beam welding (EBW). Materialwissenschaft und Werkstofftechnik (Materials Science and Engineering Technology) 43(10):892–897. https://doi.org/10.1002/mawe.201200933
Watt IM (1997) The principles and practice of electron microscopy. Cambridge University Press, Cambridge, pp 89–90. https://doi.org/10.1017/CBO9781139170529
Oatley CW (1972) The scanning electron microscope. Cambridge University Press, Cambridge, pp 1–2
Wong H (2017) Pilot investigation of feedback electronic image generation in electron beam melting and its potential for in-process monitoring. Elsevier Journal of Materials Processing Technology, in-press
Petrovic V, Haro JV, Blasco JR, Portolés L (2012) Additive manufacturing solutions for improved medical implants, Biomedicine, Dr. Chao Lin (Ed.), ISBN: 978-953-51-0352-3, InTech, pp 173
Tan X, Kok Y, Tor SB, Chua CK (2014) Application of electron beam melting (ebam) in additive manufacturing of an impeller, Proceeding of the 1st International Conference on Progress in Additive Manufacturing. https://doi.org/10.3850/978-981-09-0446-3_076
Gonzalez RC, Woods RE (2008) Digital image processing, Pearson Education, Inc, pp 122–127, 322-327
Arcam A1 EBAM machine specification: http://www.arcam.com/wp-content/uploads/Arcam-A1.pdf
Acknowledgements
The EBAM machine was purchased, in part from a grant received for the EPSRC Centre for Innovative Manufacturing in Additive Manufacturing.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no conflict of interest.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Wong, H., Neary, D., Jones, E. et al. Pilot capability evaluation of a feedback electronic imaging system prototype for in-process monitoring in electron beam additive manufacturing. Int J Adv Manuf Technol 100, 707–720 (2019). https://doi.org/10.1007/s00170-018-2702-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-2702-6